Mini DC 5A Motor PWM Speed Controller 3-35V Speed Control Switch LED Dimmer
Mini Disc Vibrating Motor
Mini Electric Drill Chuck 0.3-4mm Jto Taper-Mounted Lathe PCB Drill Press
- High precision screw thread and tapered hole.
- Strong impact resistance.
- Compatible with impact drill and different power electric drill.
- jt0 taper the biggest end of diameter: 6. 350mm
- jt0 taper the smallest end of diameter: 5. 800mm
- Outer diameter: 21. 5mm
- Drill Clip aperture: 6mm
- Taper type outside diameter drill chuck: 21mm
- Clamping range: 0. 3mm-4mm drill,
- Maximum clamping: 4.2mm
- Fit motor shaft diameter 3. 17mm
- Connection size: jt0 (inner hole diameter is 6 mm) for milling machine, lathe, drilling machine, woodworking machine
Mini ESP-M2 ESP8285 Serial Wireless WiFi Transmission Module SerialNET MODE Fully Compatible With ESP8266
ESP8285 M2 WiFi IoT Module :
- SOC characteristics.
- Built-in Tensilica L106 ultra-low power 32-bit CPU, main frequency supports 80MHz and160MHz and RTOS.
- Built-in TCP/IP protocol.
- Built-in one-channel 10-bit high precision ADC.
- Outboard interface: HSPI, UART, I2C, I2S, IR Remote Control, PWM, GPIO.
- The deep sleep current is 10uA, the cut-off current is smaller than 5uA.
- Wake, connect and transmit data package within 2ms.
- The consumer power is smaller 1.0Mw (DTIM3) when at standby status.
- Built-in 1M byte for SPI Flash.
- Ultra-small size.
- Support serial to WiFi.
- Wireless transparent transmission.
- Long-distance transmission with ultra-low power.
- Support outboard antenna.
- Bearing high temperature to 125 °C, compared to the 85°C for ESP8266.
- Support 802.11 b/g/n/e/I.
- Support Station, Soft AP, Soft AP+STA mode.
- Support WiFi Direct (P2P).
- Support CCMP (CBC-MAC, computation mode), TKIP (MIC, RC4), WAPI (SMS4), WEP (RC4), CRC etc., for hardware acceleration.
- P2P finding, P2P GO mode/ GC mode and P2P power management.
- WPA/PA2PSK and WPS.
- 11securitycertification: pre-certification and TSN.
- Support 802.11n (2.4GHz).
- 1h/RFC1042 frame encapsulation.
- Support seamless roaming.
- Support AT remote update and cloud update (OTA).
- Support Smart Config function (including Android and Ios device
MINI L293D Motor Drive Module
Mini LCD Digital Thermometer Sensor Wired for Room Temperature
- Temperature Range: -50 to +110°C
- Temperature Display Resolution: ±0.1
- Temperature Measurement Accuracy: 1°C
- Cable Length: 1 Meter
- Easy to use, small, and handy module.
- Module powered by a pair of LR44 button batteries.
- Display Size: 34 x 15 mm
- Dimension: 46 x 26 x 15 mm
- LCD Digital Thermometer for Aquarium Freezer H155 New modelling is simple, elegant.
- LCD panels connections online, moisture-resistant, strong anti-interference
Mini Micro SD Card Reader module
Mini Microwave Radar Motion Sensor
Specifications
-
Sensor Type: Microwave / Radar Motion Sensor
-
Operating Voltage: 220–240V AC
-
Detection Angle: 360°
-
Detection Range: 5–8 meters (approx.)
-
Installation: Ceiling / Surface Mount
-
Load Compatibility: LED, CFL, Incandescent (via relay/module)
-
Working Frequency: 5.8 GHz
-
Material: ABS Plastic
-
Color: White
Applications
✔ Smart Lighting Systems
✔ Automatic Corridor & Staircase Lights
✔ Washrooms & Parking Areas
✔ Security & Surveillance Systems
✔ Home Automation Projects
✔ Industrial & Commercial Automation
MINI NODEMCU ESP8266 WIFI DEVELOPMENT BOARD BASED ON ESP-12F
- Communication interface voltage: 3.3V
- Working current: 240mA(MAX)
- Serial port baud rate: 115200 (default), can be modified to other values by AT command
- Serial communication format: 8N1
- Wireless Network Mode: station / softAP / SoftAP + station
- Wireless criteria: 802.11 b / g / n
- WIFI @ 2.4 GHz, support for WPA / WPA2 security mode
- +19.5dBm output power
- Compatible with ESP-12（ESP-202）
- It is very easy to develop projects with AT commands
- Surface Mount Package with 2mm Pitch Pads
- Multiple GPIO’s for all your sensor needs
- Integrated TCP/IP protocol stack
- Integrated TR switch, balun, LNA, power amplifier and matching network
- Integrated PLL, regulators, DCXO and power management unit
- Power down leakage current of <10uA
Mini OSD W/ KV Team MOD For Racing F3 Naze32 Flight Controller RC Drone
- NO DC/DC converter, hence less heating
- FTDI cable compatible pinout
- Standard 6-pin ISP header
- Two LED indicators
- ATmega328P with Arduino bootloader
- MAX7456 monochrome on-screen display
- Pad for an Analog or Digital PWM RSSI signal
- Pad for the connection of a Current Sensor
- ATmega328P with Arduino bootloader
- Standalone, or with APM / Flip / Flip32+ flight controllers
- These modifications allow direct connection of two batteries (up to 4S)
- This hardware takes the hardware mods for this firmware and builds them into an RTF solution.
- This Board can be used just as a normal OSD for APM or it can be used with MWC KV Team Mod.
- Two independent power sections with an LED indicator on each.
- Solder jumpers for combining the power sections
- Solder jumper for PAL video option
- +5V 500mA regulator for up to +12V supply input
- Exposed test points for HSYNC and LOS ATmega328P with Arduino bootloader.
- Dimension: 16 x 16mm
Mini Portable Virtual Laser Projection Keyboard and Mouse Wireless Bluetooth
- Compatible with Android, iOS, Windows and Mac all kinds of operation systems that can be used with any phone, tablet, PC and laptop for a smooth and fast way of text input.
- Built-in Bluetooth for connecting to other devices without complex wired troubles
- More stable and smarter
- Can change the mini USB port to micro USB port.Â
- With mini Bluetooth speakers, which support voice reporting and music playing
- 3 in 1 Function: Laser keyboard,Mouse and bluetooth speaker
- Good touch sensitivity
- The BEEP sound and brightness can be adjusted on the laser keyboard
Mini SMD NRF24L01 2.4G Wireless Data Transmission Module
- Maximum operating speeds up to 2Mbps
- GFSK modulation efficiency, Anti-interference ability,
- Built-in hardware CRC error detection, Multipoint communication address control.
- Low-power 1.9 to 3.6V, only 1uA on Power-down mode
- Built-in 2.4Ghz antenna
- Built-in voltage regulator
- 125 Channels, Multi-point communication, and frequency hopping to meet the communication needs
- Wireless transceiver including Frequency generator, enhanced type, SchockBurstTM, mode controller, power amplifier, crystal amplifier, modulator, demodulator
- The output power channel selection and protocol settings can be set extremely low current consumption, through the SPI interface
- In the transmit mode, the transmit power is 6dBm, the current is 9.0mA, the accepted mode current is 12.3mA, the current consumption of the power-down mode and standby mode are lower
- Standard DIP Pitch Interface for embedded applications.NRF24L01 SPI interface: hardware SPI port, MCU I/O ports
- Internal FIFO compatible with a variety of microprocessor interface, micro-controller is convenient