Anti-Corrosion Water Level Sensor with Ball Float Switch
- Rating Contract (Max.): 10 W
- Switching Power Supply (Max.): 110VDC
- Pulse current (Max.): 0.5A
- Breakdown Voltage (Max.): 220VDC
- Current (Max.): 1A
- Resistance Contract (Max.): 100 Ω
- Operating Temperature: -10 to 60degree C
- Cable length: 40cm
- Shipment Weight: 0.02 kg
- Float Ball Size : 24×17mm
- Body Total Length: 85mm
- Total Float opening: 70°
- Float Switch ON/OFF angle: Approx. between 15° to 20°
Brass G1/4″ BSP Hall Effect Flow Sensor Water 0.35-3.0L/min OD12 WaterTurbine Flowmeter SEN-HZ41WC
- Water quality requirement: Drinking water health standards, 0-80℃.
- Flow range: 0.35 -0 Liter/min.
- Withstand hydraulic pressure: ≤1.75 MPa.
- Operating voltage: DC 4.5 - 18 Volt
- Operating current: ≤15mA.
- Insulation resistance: >100MΩ.
- Electrical strength: AC500V, 50HZ.
- Output level: Rated voltage DC5V, high level ≥4.5 Volt, low level ≤0.5 Volt.
- Pulse duty cycle: 50%.
- Flow characteristic: F=73Q, F: HZ, Q: L/min，±10%.
- Cumulative flow conversion: 1 Litre water=1780 pulse, accuracy: 8%.
SEN-HZ21WI DN15 1/2 Copper Water Flow Sensor Output Flow Sensor Switch
- Model: SEN-HZ21WI
- Material: Copper
- Colour: Gold
- Type: 1/2(External Thread Diameter)
- Water quality requirement: ≤60℃
- Flow range: 1-30L/min
- Maximum water pressure: 1.75MPa
- Three-wire connection: Red for positive pole, black for negative pole, yellow for pulse signal
- Lightweight, reasonable size, stable performance, low water pressure start, easy to install, safe to use
- Weight: approx. 95g
APDS-9930 Gesture Sensor Digital Proximity And Ambient Light Sensor For Arduino
- Working voltage:2.8-3.8V
- ALS, IR LED, and Proximity Detector in an Optical Module
- Approximates Human Eye Response
- Programmable Interrupt Function with Upper and Lower Threshold
- Programmable range from 2.7 ms to more than 8 seconds
- Up to 16-Bit Resolution
- High Sensitivity Operates Behind Darkened Glass
- Low Lux Performance at 0.01 lux;
- Ambient Light Sensing (ALS)
- Proximity detection
- I2C interface is compatible up to 400kHz (I2C fast mode) –
OV7670 Camera Module
- Model: OV7670 640X480 VGA CMOS CAMERA
- I/O Voltage: 2.5V to 3.0V
- Operating Power: 60mW/15fpsVGAYUV
- Sleeping Mode: <20μA
- Operating Temperature: -30 to 70 degrees Celsius
- Pixel Coverage: 3.6um x 3.6um
- Lens Size: 1/6″
- Vision Angle: 25 degrees
- Frame Rate: 30fps VGA
- Sensitivity: 1.3V / (Lux-sec)
- Signal to Noise Ratio: 46 dB
- Dynamic Range: 52 dB
- Browse Mode: By row
- Electronic Exposure: 1 to 510 row
- Duck Current: 12 mV/s at 60℃
- PCB Size (L x W): Approx. 1.4 x 1.4 inch / 3.5 x 3.5 cm
- Support VGA, CIF and from CIF to 40 x 30 format
- Various Pixel methods for sub-sampling; Auto Image Control: AEC, AGC, AWB, ABF, ABLC;
- Image Quality Control: Colour saturation, hue, gamma, sharpness, and anti-blooming;
- DSP includes noise reduction and defect correction; Support image scaling; Lens shading correction;
- Flicker 50/60Hz auto-detection
- Colour saturation level auto adjust
- Edge enhancement level auto adjust
- De-noise level auto adjust
- High sensitivity for low light applications
- Low voltage suitable for embedded applications
- Standard SCCB interface, compatible with I2C interface
Square MAX7219 8×8 LED Dot Matrix Display Module
- Driver Chip: MAX7219
- Input Voltage: 3.7 to 5.3 V
- Input Current: 320 mA
- Display Dimensions: 32x32x6 mm
- PCD Dimensions: 50×32 mm
- A single module can drive an 8 * 8 common cathode lattice
- Requires only 3 communication wires of MCU
- Cascading multiple Matrix LED Module is very easy
- The size of the display is very compact
- The PCB features M3 holes for mounting.
KA2284 Audio level Indicator
- Chip: KA2284.
- Wide operating supply voltage: 3.5V-16V
- `Level amplitude can be adjusted.
- AC/DC signal can be controlled through the jump line.
- High gain rectifying amplifier included(Gv=26dB)
- Low radiation noise when LED turns on
- Logarithmic indicator for 5-dot LED of bar type.
- Constant current output( 15mA)
- Minimum number of external parts required
- PCB board size: 29 x 21 mm
Attiny 85
- High Performance, Low Power AVR® 8-Bit Microcontroller
- Non-volatile Program and Data Memories
- 8K Bytes of In-System Programmable Program Memory Flash
- Endurance: 10,000 Write/Erase Cycles
- 512 Bytes In-System Programmable EEPROM
- Endurance: 100,000 Write/Erase Cycles
- 512 Bytes Internal SRAM
- Peripheral Features
- High-Frequency PWM Outputs with Separate Output Compare Registers
- USI – Universal Serial Interface (12C, SPI, 1-wire) with Start Condition Detector
- 10-bit ADC
- Single-Ended Channels
- 2 Differential ADC Channel Pairs with Programmable Gain (1x, 20x)
- Speed Grade: 0 – 10 MHz @ 2.7 – 5.5V, 0 – 20 MHz @ 4.5 – 5.5V
- Low Power Consumption
- Active Mode:1 MHz, 1.8V: 300 µA
Plastic Power Lock/Ignition Key Switch – 2 pin Female
- Comes with 2 pins male connector (white) and includes 2 keys.
- Applicable for MY1016 controllers.
- Wire Length: 270mm
- Total lock Length: 325mm
- Plug is 11mm x 6mm.
- Durable, convenient to use.
- Easy installation, with 2 keys.
- Designed with a reliable ignition switch locking mechanism.
- Fitment: Fit for electric bicycle, Carting.
- ​Material: Plastic.
XH-W3001 DC 12V 120W Digital Microcomputer Thermostat Switch
- Rated Current: 10 Amp Max.
- Measurement Input: NTC10K
- Temp Probe Cable Length: 1 Meter
- Power Supply: DC12V
- Load Power: 120W
- Easy to install
- Output type: Direct output
- Output capacity: max 10A
- Temperature setting upper and lower limits
- Temperature measuring range: -50~110°C
- Temperature control range: -50~110°C
- Control precision: up to 0.1°C
- Up key: Press once to display the start temperature. Long press to set start temperature.
- Down key: Press once to display the stop temperature. Long press to set stop temperature.
- Temperature setting upper and lower limits
- Simple operation, suitable for seafood machines.
- Dimensions 60 x 45 x 31 (mm)
- Weight: 55gm
Single Phase Voltage Mutual Inductor AC Active Output Module ZMPT101B 2mA
- Supply voltage: 5-30v
- Product model: ZMPT101B
- Rated input current: 2mA
- Rated output current: 2mA
- Change ratio: 1000:1000
- Phase difference: ≤20′
- Linear range: 0~1000V 0~10mA
- Linearity: ≤0.2%
- Allowable error: -0.3≤f≤0.2%
- Isolation withstand voltage: 4000V
- Uses: accurate measurement of voltage and power
- Sealing material: epoxy resin
- Installation method: printed board installation
- Working temperature: -40 to +60 degrees
- Shell material: ABS
- Voltage up to 250 volts can be measured
- Lightweight with on-board micro-precision voltage transformer
- High precision on-board op-amp circuit
- Good consistency, for voltage and power measurement
- Very efficient and accuracy