3/4″ Brass Electric Solenoid Valve 12VDC N.C. Air Water Fuel
- Size: 3/4"
- Flow Aperture: 20 mm
- Body Material: Brass
- Gasket / Diaphragm / Seal: VITON
- Rated voltage: DC 12 V, ± 10%
- Current: 1.667 A
- Power rating: 20 W
- Operation Type: Semi-direct Lift Valve
- Operation Mode: Normally Closed
- Operational pressure range: 0 to 101 PSI / 0-0.7 Mpa (for Air, Water); 0 to 72 PSI / 0-0.5 Mpa (for Oil)
- Flow capacity: 7.6 gallons per minute (GPM) of water at 60oF with a pressure drop of 1 PSI
- Flow value: 7.6 Cv
- Minimum operational temperature: 14 degrees Fahrenheit (-10 degrees Celsius)
- Maximum operational temperature: 248 degrees Fahrenheit (120 degrees Celsius)
- Suitable Media: Air, water, oil, natural gas, diesel fuel, kerosene etc. Can not be used in strong acid, strong base, waste water, industrial gas and other media containing many impurities.
- Quality assurance: CE Certified
MH1210W 72V 250V 10A Digital Temperature Controller
- Working voltage: DC 9-72V/AC90-250V ± 10%, 50/60 HZ
- Rated current: 10 A
- Power consumption: ≤3 W
- Measurement range: -50~110 °C
- Measurement precision: 0.1 °C
- Measurement error: ±0.3 °C
- A mini temperature controller.
- Large and clear LED display for better readability
- Wide temperature measuring range
- Heating and cooling control
- Temperature calibration
- Delay protection function
- All parameters reset to default settings after short circuit
L293D Motor Driver Board for ESP8266 WiFi NodeMcu Lua ESP12E
- Motor power supply Range: 4.5V ~ 36V
- Control power Range: 4.5V ~ 9V (10VMAX)
- Logic Operating current: ≤60mA
- Drive part of the work current Io: ≤1.2A
- Maximum power dissipation: 4W
- Drive Type: Dual high-power H-bridge driver
- Working temperature: -25 ℃ ~ + 125 ℃
- ESP12 DEV KIT development board expansion module
- Lead ESP12 DEV KIT all the features of pins: SPI, UART, GPIO, AI, and 3.3V power connector
- Extend two-way motor-driven, two-way direct-drive motor
- on board power switch
- Motor power, control power separation
- Dimension: 60 x 45 x 13mm
AZDS2-0XDQSA4 Hex Drive Power Drill Socket Extension Bit Adaptor Set – Pack of 3 Pieces
- Material: Chrome Vanadium steel
- Shank Type: Hex Shank
- Size- 1/4, 3/8,1/2-inch.
- Pack of 3.
- Available in multicolour.
- Good quality product.
- Can be used for prolonging different kinds of screwdrivers.
- Built-in magnetic, fast, fastening, greatly improve work efficiency.
- Suitable for electric drill, screwdriver, wind batch transfer using to play the role of releasing bit holder.
- Interface comes with a locking function
YF-S402 High Precision Flow Meter Water Flow Sensor
- Model: YF-S402
- Minimum rated working voltage: DC 5~24V;
- working current: 15mA (DC 5V);
- Working voltage range: DC 5~18V;
- Load capability: <= 10mA (DC 5V);
- Working temperature: <= 80'C;
- Humidity range: 35%~90%RH (no frost);
- Water pressure: <1.75Mpa;
- Storage temperature: -25~80'C; Storage humidity: 25~95%RH;
- Flow range: 1~5L/min'; Frequency: 4380 pulse for 1L through the sensor
- Dimensions: 2.28 in x 1.38 in x 1.06 in (5.8 cm x 3.5 cm x 2.7 cm)
- Thread Size : G1/4"
6V 12V 24V 8A PWM DC Motor Speed Controller CCM5D Digital Display LED Motor Controller Speed Regulator
- Input Supply Voltage: 6V-30VDC
- Continuous Current (A): Rated current 5A (8A MAX, cannot be prolonged)
- Maximum Output Power: 240W
- LED display the duty ratio: 0-100%
- PWM Frequency: 16khz
- Duty Cycle adjustable: 0%-100%
- Dimensions: 78*42*25mm
- The display range of 3-digit LED display is "000"-"100".
- Adjustable speed range is 0%-100%
- Fine workmanship and good performance.
- Easy to use.
- Long service life.
- Suitable for the DC motor (or DC load) within 5A, Peak current 8A.
- Incorporate a push key. Push closed, and then push open
SMA Pigtail Cable To Ufl Extension Cable 1.13 Cable
TP5100 4.2v 8.4v Single Double Lithium Battery Charge Management Li-ion Battery Compatible 2A Charging Board
- Input voltage: 5-15V DC power supply.
- Charge status: full and unloaded blue lights, charging red.
- Double 8.4v / 4.2v lithium rechargeable single .
- Programmable charge current. 0. 1A-2A .
- Programmable steady precharge current 10% -100%.
- Wide operating voltage, maximum reach I8V.
- Red and green LED charge status indicator.
- Chip temperature protection, overcurrent protection, under voltage protection.
- Battery temperature protection, reverse battery shutdown, short circuit protection.
- Switching frequency 400Khz, usable inductance 20uH and more.
- PWR_ON Power battery for switching control.
Mh13001 220V Digital Air Humidity Control Controller Range 1% – 99%
- Model Name: MH 13001
- Voltage: 220 Volt
- Accuracy: +-3% RH
- Type: Digital
- Color: Black
- Display Type: LCD
- Input Sensor: Humidity Sensor
- Humidity: 1% ~ 99% RH\humidity measuring
- Error: ±3 percent rh
- Control range: 1 percent RH
- Power consumption:3w
- Output load: Ac 10a/220v
- Working temperature: 0°c - 80 °c
- Dimensions: 8 x 5 x 3cms
- Usage/Application: Air Humidity Controller Hygrostat Humidistat Humidification Dehumidification
Worm Gear Box Reduction Motor 12V 350rpm 22 kg-cm Torque – WGM5551212000-34K
Worm Gear Box Reduction Motor 12V 85rpm 6 kg-cm Torque – WGM370128500-100K
- Motor Type: DC Carbon Brush Motor.
- Gear Ratio:100: 1.
- Operating Voltage: 12.V DC
- Rated Current: 0.220A
- Rated Base Motor RPM: 8500.
- Rated Speed: 85RPM
- Rated Torque: 6kg-cm
- Operating Temperature: (°C) - -40 °C ～ +100°C.
- Relative Humidity(RH): 20% ～ 85% .
- Housing Material: Metal.
- Shaft Type: D-type.
- Motor Height: 25mm
- Motor Width: 32mm.
- Motor Length:Â 81mm
- Shaft Diameter: 6mm
- Shaft Length: 13mm
- Shaft Type: D-type. Motor
- Weight(gm): 170.
