A3144 Hall Effect Sensor
- Digital Output Hall-effect sensor
- Operating voltage: 4.5V to 28V (typically 5V)
- Output Current: 25mA
- Can be used to detect both the poles of a magnet
- The output voltage is equal to operating voltage
- Operating temperature: -40°C to 85°C
- Turn on and Turn off time is 2uS each
- Inbuilt reverse polarity protection
- Suitable for Automotive and Industrial Applications
HX711–24 Bit Analog to Digital Converter (ADC)
- It is an ADC converter with two differential input channels
- An active-low noise PGA is integrated inside the chip which provides the gain of 32, 64 and 128
- It has a power-on-reset capability which simplifies digital interface initialization.
- All controls to the IC are made through the pins. Programming is not needed.
- You can select a data rate of 10SPS or 80SPS at the output.
- Provides simultaneous supply rejection of 50Hz and 60Hz supply.
- Built-in analog power supply regulator
- The voltage supply range is from 2.6V to 5.5V
- The temperature range is from -40 °C to +85℃
ACS712 20A Hall Current Sensor Module SMD SOP8 SOIC8
- Low-noise analog signal path
- Device bandwidth is set via the new FILTER pin
- 5 µs output rise time in response to step input current
- 80 kHz bandwidth
- Total output error 1.5% at TA= 25°C
- Small footprint, low-profile SOIC8 package
- 2 mΩ internal conductor resistance
- 1 kVRMS minimum isolation voltage from pins 1-4 to pins 5-8
- 0 V, single supply operation
- 66 to 185 mV/A output sensitivity
- Output voltage proportional to AC or DC currents
- Factory-trimmed for accuracy
- Extremely stable output offset voltage
- Nearly zero magnetic hysteresis
- Ratiometric output from supply voltage
Motor Driver IC – L293D
- Can be used to run Two DC motors with the same IC.
- Speed and Direction control is possible
- Motor voltage Vcc2 (Vs): 4.5V to 36V
- Maximum Peak motor current: 1.2A
- Maximum Continuous Motor Current: 600mA
- Supply Voltage to Vcc1(vss): 4.5V to 7V
- Transition time: 300ns (at 5Vand 24V)
- Automatic Thermal shutdown is available
- Available in 16-pin DIP, TSSOP, SOIC packages
- Featuring Unit rode L293 and L293D
- Wide Supply-Voltage Range: 4.5 V to 36 V
- Separate Input-Logic Supply
- Internal ESD Protection
- Thermal Shutdown
- High-Noise-Immunity Inputs
- Output Current 1 A Per Channel (600 mA for L293D)
- Peak Output Current 2 A Per Channel (1.2 A for L293D)
- Output Clamp Diodes for Inductive Transient Suppression
ADXL 335 Accelerometer IC
- 3-axis sensing
- Small, low profile package
- 4 mm × 4 mm × 1.45 mm LFCSP
- Low power : 350 μA (typical)
- Single-supply operation: 1.8 V to 3.6 V
- 10,000 g shock survival
- Excellent temperature stability
- BW adjustment with a single capacitor per axis
- RoHS/WEEE lead-free compliant
- 8V- 3.6V single-supply operation
- Integrated X, Y, and Z axis accelerometer on a single chip
- X and Y axis has a 0.5Hz to 1600Hz bandwidth
- Z axis has a 0.5Hz to 550Hz bandwidth
- Hermetically sealed for temp and humidity resistance
SW520 ball switch angle Tilt switch vibration switch
- Model: SW-520D
- Type: Ball
- Material: Housing and cover: PE heat shrinkable tubing
- Ball Material: Stainless steel, gold-plated
- Guide pin: Brass, gold-plated / Copper tube: Brass
- Shape: Round
- color:Black / Gray
- Contact Rating:12V
- Differential angle:
- Contact Resistance: <10 ohm
- Insulation Resistance:>10M ohm
- Capacitance:5Pf
- SW-520 two balls type single direction tilt sensitive trigger switch
- The switch is completely airtight, waterproof, dustproof
- In the normal, switch life span can reach 10,0000 cycles
- Switches material comply with the ROHS and can replace the mercury switches.
- Switch signals simple, the circuit is simple in design, economic price.
HDMI Male to VGA Female Converter Adapter 1080P For PC, Rspberry Pi
- Support HD resolution, super clear picture, fast transmission speed
- The maximum signal range up to 1920 X 1200, 1080p;
- Video input signal: 5Volts p-p(TTL) ;
- Support VGA video bandwidth: 10 bit, 162MHz
- Video amplifier bandwidth: 162MHz
- Support resolution up to 1920 X 1200, reduce blank signal during transmit.
- No external power supply, plug, and play.
USB 2.0 Type A Male to USB A Male Cable
- USB 2.0
- Length:1m
- A-A male cable type
- Blue colored cable
- Standard USB 2.0 cable assembly, Type A male to type A male
- signaling rate: 480 Mbit/s (60 MB/s) Connector Type: USB 2.0 Type A Male to Type A Male
- High quality USB 2.0 high speed cable. Usually used for some external drive enclosures or cameras.
- Fully Compatible with USB 1.0,1.1 , Supports data transfer rate at up to 480Mbps
- Supports plug play connections for devices such as external hard drives, modems, printers, scanners, VOIP devices other USB peripherals.
- It is plug & play and hot swappable (no need to turn off your PC to plug a device in or out).
A-Male to A-Female USB 2.0 Extension Cable (150cm)
- Hi-Speed 480 mbps With 3g Dongle Support.
- Easy to operate, bring you great convenience.
- Made of high-quality Material
- USB 2.0 A Male to A Female Extension Cable.
- A-male to A-female USB cables are typically used to extend the reach of your existing USB A/B cable, or to use USB device such as memory stick on your desk instead of inserting it to the back of PC
- Left connector type: USB 2.0.
- Left connector gender: Male.
- Right connector type: USB 2.0.
- Right connector gender: Female
A-to-Mini B USB-2.0 Cable for Arduino Nano
- USB Type: Type-A to Mini-B
- Weight: 100 gm.
- Length: 1.35 m.
- Nickel-Plated Connector
- Exclusively designed for Arduino boards.
- Exclusively designed for Arduino boards.
- Mini-USB cables are designed to connect from the USB port on a hub, PC or Mac to a USB device, including digital cameras, mobile phones, and PDAs.
Serial RS-232 9 Pin Cable Male to Male
- Connector Type: DB9 Male to DB9 Male.
- Cable diameter: 6mm
- Cable length:1.5m
- Fully shielded to prevent unwanted EMI/RFI interference.
- Fully molded connectors with thumbscrews provide quick and easy connection.
- All lines wired straight through.
- Used for extending a 9 pin serial male to male cable, or connect it to an old serial port device along with a serial to USB converter
- Shielded with standard Foil-Al layer shielding as in most cables
Serial RS-232 9 Pin Cable Male to Female
- Connector Type: DB9 Male to DB9 Female.
- Cable diameter: 6mm
- Cable length:
- Fully shielded to prevent unwanted EMI/RFI interference.
- Fully molded connectors with thumbscrews provide quick and easy connection.
- All lines wired straight through.
- Used for extending a 9 pin serial male to male cable, or connect it to an old serial port device along with a serial to USB converter
- Shielded with standard Foil-Al layer shielding as in most cables