74LS540 High-Speed CMOS Logic Octal Buffer and Line Driver IC
7806 6V Positive Voltage Regulator IC
- Output current up to 1A
- Output Voltage: 6V
- Line Regulation (max): 120mV
- Load Regulation (max): 120mV
- Dropout Voltage: 2V
- Output Resistance: 19mΩ
- Output Voltages of 5, 6, 8, 9, 12, 15, 18, 24
- Internal thermal overload protection
- No external components required
- Output transistor safe area protection
- Internal short circuit current limit
- Available in the aluminium TO-3 package
- Thermal Overload Protection
- Short Circuit Protection
- Output Transistor Safe Operating Area Protection
Soldering Iron Stand
36V/48V/60V Lithium battery case 400*165*90mm ABS Plastic material
- Dimensions: 400*165*90mm.
- Suitable for battery type: 36/48/60V.
- Battery standard: 18650 lithium battery.
- Charging voltage: 42V/54.6V.
- Used to install an electric vehicle lithium battery.
- Suitable for electric bicycles, electric bicycles, and folding electric vehicles.
- Made up of plastic, which is sturdy and durable.
- The product has a charging socket and an output port.
36V/48V/60V Lithium battery case 360*160*100MM APS Plastic Material
- Dimensions: 360*160*100mm.
- Suitable for battery type: 36/48/60V.
- Battery standard: 18650 lithium battery.
- Charging voltage: 42V/54.6V.
- Used to install an electric vehicle lithium battery.
- Suitable for electric bicycles, electric bicycles, and folding electric vehicles.
- Made up of plastic, which is sturdy and durable.
- The product has a charging socket and an output port.
36V/48V Fold bike Lithium Battery Case 410*100*42mm Aluminum Alloy Material
- Dimensions: 410*100*42mm.
- Suitable for battery type: 36/48V.
- Battery standard: 18650 lithium battery.
- Charging voltage: 42V/54.6V
- Used to install an electric vehicle lithium battery.
- Suitable for electric bicycles, electric bicycles, and folding electric vehicles.
- Made up of aluminium alloy and plastic, which is sturdy and durable.
- The product has a charging socket and an output port.
HC-05 Bluetooth Shield for Arduino
- Bluetooth serial port Profile
- Bluetooth protocol: Bluetooth Specification v2.0+EDR
- Frequency: 2.4GHz ISM band
- Communication Range: 10M
- Serial Bluetooth module for Arduino
- Can operate in Master, Slave or Master/Slave mode
- UART interface (TTL) with programmable baud rate (SPP firmware installed)
- Default baud rate: 38400(CMD MODE) / 9600(DATA MODE), data bits: 8, stop bit: 1, Parity: No parity
- Onboard PCB antenna
- FCC ID certificated
2.4″ Inch Touch Screen TFT Display Shield for Arduino
- 4″ Touch LCD TFT display module for Arduino
- 240*320 pixels resolution
- Ability to display 262000 different colours
- The shield comes equipped with a microSD card slot.
- SPFD5408 controller with built-in video RAM buffer
- 8-bit digital interface, plus 4 control lines
- 5V compatible. Use with 3.3V or 5V logic
- On-board 3.3V 300mA LDO regulator
- Uses digital pins 5-13 and analogue 0-3. That means you can use digital pins 2, 3, and analog 4 and 5. Pin 12 is available if not using the microSD
- Works with any Arduino Uno and mega compatible boards
- Resolution: 240320 pixels
- Supply voltage: 5V
- Working temperature: -30C ~ 70C
- Dimension: 72*52*12mm
ESP8266 WIFI Shield
- Operating voltage 5V (supplied from the Arduino Board)
- Connection via: 802.11b/g networks
- Encryption types: WEP and WPA2 Personal
- Connection with Arduino on SPI port
- on-board micro SD slot
- ICSP headers
- FTDI connection for serial debugging of WiFi shield
- Mini-USB for updating WiFi shield firmware
- 32-bit RISC architecture
- The processor can operate at 80MHz / 160MHz
- 32MB flash memory
- 64kB for instructions
- 96kB for data
- Operates in AP, Station or AP + Station mode
- It has 11 digital pins
- It has 1 analogue pin with 10-bit resolution
- Digital pins except the D0 have interrupts, PWM, I2C and one wire
- Programmable through USB or WiFi (OTA)
- Compatible with Arduino IDE
- Compatible with modules and sensors used in Arduino
PN532 NFC/RFID Controller Shield for Arduino
- PN532 chip-set
- Operating Voltage : 3.3V ~ 5v
- Support I2C, SPI
- I2C: 3.3V ~ 24V TTL
- SPI: 3.3V TTL with 100-ohm resistors in series
- Plug and play, Arduino compatible
- Built-in PCB Antenna
- Communication distance:10cm
- Easy to change mode
- NFC/RFID PN532 shield including a tuned 13.56MHz stripline antenna
- 36-pin 0.1" header for attaching the shield to an Arduino.
- Compatible with Arduino Mega 1280 & 2560, Diecimila, Duemilanove, and UNO
16×2 (1602) LCD Keypad Shield
- Operating Voltage:5V
- 5 Push buttons.
- RST button to reset Arduino program.
- Integrate a potentiometer for adjusting the backlight.
- Expanded available I/O pins.
- Blue light with white characters.
- Uses 4 Bit Arduino LCD Library
- Screen contrast adjustment
- Arduino Reset button
- The keypad consists of 6 keys select, up, right, down, left and reset.
- To save the digital IO pins, the keypad interface only uses one ADC channel.
- The key value is read out through a 5 stage voltage divider.
L293D Motor Driver Shield
- L293D motor driver chip & 74HC595 shift register
- Four H-bridges
- Terminal blocks and jumper to connect external power, for separate logic/motor supplies
- Up to 4 bi-directional DC motors with individual 8-bit speed selection
- Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil or interleaved stepping.
- 2 connections for 5V ‘hobby’ servos connected to the Arduino’s high-resolution dedicated timer
- 4 H-Bridges: L293D chipset provides 0.6A per bridge (1.2A peak) with thermal shutdown protection, internal kickback protection diodes. Can run motors on 4.5VDC to 25VDC.
- Pull-down resistors keep motors disabled during power-up
- Big terminal block connectors to easily hook up wires (18-26AWG) and power
- Arduino reset button brought up top
- Tested compatible with Arduino Mega 1280 & 2560, Diecimila, Duemilanove, and UNO
- PCB Size: 69 x 53 mm