350W 36V Electric Bike Bicycle Front Hub motor DIY Conversion Kit
350W 36V Hub Motor for Electric Bike Bicycle Front
N20 Model – 500 RPM DC 12V Torque Gearbox Micro Gear Box Motor
- Reduction ratio - 1:30.
- Nominal Voltage - 6v
- Voltage Range - 3v to 12v
- RPM - 500
- No-load Current - 40mA
- Stall Current - 550mA
- Stall Torque - 400 g-cm
- Ideal for making robots
- Lightweight, high torque and low RPM.
- Fine craftsmanship, long-lasting, not easy to wear.
- Can easily mount a wheel on the motor’s output shaft.
N20 Model – 300 RPM DC 12V Torque Gearbox Micro Gear Box Motor
- Reduction ratio: 1:50.
- Nominal Voltage: 6v
- Voltage Range: 3v to 12v
- RPM: 300
- No load Current: 40mA
- Stall Current: 550mA
- Stall Torque: 700 g-cm.
- Ideal for making robots
- Lightweight, high torque and low RPM.
- Fine craftsmanship, long-lasting , not easy to wear.
- Can easily mount a wheel on the motor’s output shaft.
N20 Model – 40 RPM DC 12V Torque Gearbox Micro Gear Box Motor
- Reduction ratio: 1:380.
- Nominal Voltage: 6v.
- Voltage Range: 3v to 12v.
- RPM: 40.
- No-load Current: 40mA.
- Stall Current: 550mA.
- Stall Torque: 7500 g-cm.
- Ideal for making robots
- Lightweight, high torque, and low RPM.
- Fine craftsmanship, long-lasting, not easy to wear.
- Can easily mount a wheel on the motor’s output shaft
Leadshine DMA860E Stepper Motor Driver
- Model: DMA860E.
- Control Mode: Step & Direction.
- Max Input Frequency: 200 kHz.
- Input Voltage Range: 18 - 80 VAC / 24 - 110 VDC.
- Suggested Power Supply Voltage Range: 36-90 VDC /24-60 VAC.
- Number of DIP Switch Resolution Configurations: 16.
- 16 selectable micro-step resolutions of 400-51,200 via DIP switches.
- 8 selectable output current settings of 2.4 – 7.2A via DIP switches.
- Logic Current Range: 7-16mA (10mA typical).
- Logic Voltage Range: 4-5 VDC for pulse active high (default), or 0-0.5V for pulse active low.
- Pulse enabled at: Rising edge.
- Idle Current Percentage: 50 %.
- Number of Digital Inputs: 3.
- Step Width: 2,500 ns.
- Minimal Direction Setup Time: 5,000 ns.
- Isolation Resistance: 500M Ohm..
- Ambient Temperature: 0-50°C.
- Humidity: 40–95% RH.
- Operating Temperature: 0-70°C.
- Vibration: 5.9 m/s2 Max.
- Motor auto-identification and parameter auto-configuration for optimal torque from wide-range motors.
- Step & direction (PUL/DIR) and CW/CCW (via internal jumper set) control. Step & direction by default Multi-Stepping for smooth motor movement.
- Opto Isolation for input control signals.
- Soft-start with no “jump” when powered on.
- Protections for over-voltage and over-current.
- Dimension: 5.94 X 3.82 X 2.24 Inches.
- Weight: 1.13 lbs.
Wemos D1 Mini ESP8266 NodeMCU WIFI board for Arduino
- Microcontroller: ESP-8266EX
- Operating Voltage: 3.3 V
- Digital I/O Pins: 11
- Analog Input Pins 1(Max input: 3.2V)
- Clock Speed: 80MHz/160MHz
- Flash: 4M bytes
- Length: 34.2mm
- Width: 25.6mm
- Use BRT (Bias Resistor Transistor)
- Easier into flash mode.
- 30% increase in radiating area
- Good stability.
- 11 digital input/output pins, all pins have interrupt/PWM/I2C/one-wire supported(except for D0)
- 1 analog input(3.2V max input)
- Micro USB connection
- Compatible with Arduino
- Compatible with Node MCU
- Support OTA wireless uploading
- 11 x I/O pins,1 x ADC pin
EMAX BLHELI 12Amp ESC for Quadcopter / Drones
- Based on BL Heli firmware.
- ESC Type: Brushless.
- Built in linear or switched BEC.
- Constant Current: 12A
- Burst Current: 15A
- BEC Mode: Linear BEC : 5v / 1A
- Lipo Cells: 2-4
- Constant Current: 12A.
- Support: One-shot 125 Protocol.
- Includes low voltage protection, over heat protection, and self-check functions.
- Separate power supply for MCU and BEC, helping eliminate magnetic interference.
- Fully programmable by any standard programming card or directly from your transmitter.
- Customisable throttle range.
- Weight: 11g
- Dimension: 42x20x8mm
Dual Monster Moto Shield VNH2SP30 Motor Driver 2x14A (Peak 30A)
- Driver Model: VNH3ASP30
- Current sensing available to Arduino analogue pin
- Operating Voltage: 12 V to 16V DC
- Peak Current: 14A
- Continuous Current: 30A
- of Channels: 2
- Maximum PWM frequency: 20 kHz
- MOSFET on-resistance: 19 m (per leg)
- Thermal Shutdown protection
- Under-voltage and Overvoltage shutdown.
- LED Indicator
- Dimensions: 60 x 54 x 12mm
- Weight: 19gm
AVR-ISP 10Pin to 6pin Adapter PCB for USBASP Programmer
FlexiForce Tekscan A502 Sensor
- Thickness - 0.203 mm (0.008 in.).
- Length - 81.3 mm (3.20 in.)**.
- Width - 55.9 mm (2.20 in.).
- Sensing Area - 50.8 mm x 50.8 mm (2 in. x 2 in.).
- Connector - 2-pin Male Square Pin.
- Substrate - Polyester.
- Pin Spacing 2.54 mm (0.1 in.).
- Standard Force: 222 N.
- Temperature Range (Low): -40 °C.
- Temperature Range (High): 60 °C.
- Thin and flexible.
- Ideal for prototyping and integration.
- Easy to use.
FlexiForce Tekscan A401 Sensor
- Thickness - 0.203 mm (0.008 in.).
- Length - 56.9 mm (2.24 in.)**.
- Width - 31.8 mm (1.25 in.).
- Sensing Area - 25.4 mm (1 in.) diameter.
- Connector - 2-pin Male Square Pin.
- Substrate - Polyester.
- Pin Spacing - 2.54 mm (0.1 in.).
- Standard Force Ranges - 111 N (0 - 25 lb) ; 31,138 N (0 - 7,000 lb).
- Ideal For Prototyping And Integration
- Available with Enhanced Stability Series (ESS) pressure-sensitive ink for high-temperature and High-humidity environments
- Thin and flexible
- Easy to use