FlexiForce Tekscan A301 Sensor
- Thickness 0.203 mm (0.008 in.)
- Length 25.4 mm (1 in.)**
- Width 14 mm (0.55 in.)
- Sensing Area 9.53 mm (0.375 in.) diameter
- Connector 2-pin Male Square Pin
- Substrate Polyester
- Pin Spacing 2.54 mm (0.1 in.)
- Small size is ideal for prototyping and integration
- Available with Enhanced Stability Series (ESS) pressure-sensitive ink for high-temperature and high-humidity environments
- Thin and flexible
- Easy to use
ESP8266 ESP – 03 WIFI Transreceiver Wireless Module
- Communication interface voltage: 3.3V
- Working current: 240mA(MAX)
- 802.11 b/g/n
- Wi-Fi Direct (P2P), soft-AP
- Integrated TCP/IP protocol stack
- Integrated TR switch, balun, LNA, power amplifier and matching network
- Integrated PLLs, regulators, DCXO and power management units
- +19.5dBm output power in 802.11b mode
- Power down leakage current of <10uA
- Integrated low power 32-bit CPU could be used as application processor
- SDIO 1.1/2.0, SPI, UART
- STBC, 1×1 MIMO, 2×1 MIMO
- A-MPDU & A-MSDU aggregation & 0.4ms guard interval
- Wake up and transmit packets in < 2ms
- Standby power consumption of < 1.0mW (DTIM3)
- SDIO 2.0, SPI, UART
- 32-pin QFN package
- Integrated RF switch, balun, 24dBm PA, DCXO, and PMU
- Integrated RISC processor, on-chip memory and external memory interfaces
- Integrated MAC/baseband processors
- Quality of Service management
- I2S interface for high fidelity audio applications
- On-chip low-dropout linear regulators for all internal supplies
- Proprietary spurious-free clock generation architecture
- Integrated WEP, TKIP, AES, and WAPI engines
10D OF 9-AXIS GY-87
- Power supply: DC 3.3V TO 5V
- 3 Axis Gyro+ Acceleration+ Magnetic field
- Air pressure module
- Inbuilt ultra-low noise linear LDO voltage regulator
- Inbuilt onboard filters. which reduce noise from motor and another high current
- Communication: I2C protocol
- Power LED
- Designed for 5V logic
- Can easily select two I2C addresses for MPU6050 by soldered jumper
- Dimension: 2.2*1.7cm
- Size: 6gm
Arduino Pro Mini
UV Sensor Module Ml8511 Analog Output UV Sensor Breakout
HC-05 Bluetooth Shield for Arduino
- Bluetooth serial port Profile
- Bluetooth protocol: Bluetooth Specification v2.0+EDR
- Frequency: 2.4GHz ISM band
- Communication Range: 10M
- Serial Bluetooth module for Arduino
- Can operate in Master, Slave or Master/Slave mode
- UART interface (TTL) with programmable baud rate (SPP firmware installed)
- Default baud rate: 38400(CMD MODE) / 9600(DATA MODE), data bits: 8, stop bit: 1, Parity: No parity
- Onboard PCB antenna
- FCC ID certificated
SanDisk Ultra Dual 64GB USB 3.0 OTG Pen Drive
- Compatible with Micro USB Type 'B' Android based Smartphones & Tablets
- Free up space on your OTG-enabled Android phone
- Back up your mobile photos, videos and contacts
- Retractable design with dual micro-USB and USB 3.0 connectors
- SanDisk Memory Zone application (available on Google Play) lets you easily manage your photos and videos
- High-speed USB 3.0 performance with up to 130mbps file transfer from drive to computer
- For any queries, please contact_us on: [18001205899/18004195592]
800S Analog Timer
Product Description
800S analog timer, which is an on-delay timer used to control the activation of a circuit after a set amount of time has passed. It is housed in a compact DIN rail mount and can be powered by AC or DC power options. Its designed for industrial applications and offers accurate and reliable switching. A103675
Wemos D1 WiFi Esp8266 Development Board Uno Compatible Program
- Microcontroller: ESP-8266EX
- Operating Voltage: 3.3 V
- Digital I/O Pins: 11
- Analog Input Pins 1(Max input: 3.2V)
- Clock Speed: 80MHz/160MHz
- Flash: 4M bytes
- Good stability.
- 11 digital input/output pins, all pins have interrupt/PWM/I2C/one-wire supported(except for D0)
- 1 analog input(3.2V max input)
- Micro USB connection
- Compatible with Arduino
- Support OTA wireless uploading
- On-Board Switching Power Supply:
- Micro USB connection
- Compatible with Arduino
- Support OTA wireless uploading
Solid Relay Module 4 channel 5v low level trigger for Arduino
- Operating Voltage: 5V
- Operating Current: 12.5mA
- Maximum Load: 2A @ 240VAC
- Static Current: 0mA
- Channels: 4 Channel.
- Switch Max frequency: 5KHz.
- Trigger Voltage Range:
- Separate LEDs showing the status of each Solid-State Relay
- Strong anti-interference ability and stable performance
- Dimension: :57 x 55 x 25mm
PL2303 6 pin USB to TTL RS232 convert serial cable
• Supports RS-232 serial interface with Programmable baud rate from 75 bps to 12 Mbps
• Compatible with the RS422/RS485 interface
• Extensive flow control mechanism like adjustable high/low watermark level, automatic hardware or software flow control, and inbound data buffer overflow detection.
• The cables provide a fast, simple way to connect devices with a TTL level serial interface to USB
• The TTL-232R cables are a family of USB to TTL serial UART converter cables incorporating FTD’s FT232RQ USB to Serial
• Cables are FCC, CE, RoHS compliant and are available at TTL levels 3.3V
• It is USB 2.0 full speed compatible. The USB side of the cable is USB powered.
Ethernet Shield
- Based on the W5100Based on the Wiznet W5100 allows an Arduino board to connect to the internet.
- Stackable Design, can directly be supported by Arduino official Ethernet Library.
- Supports up to four simultaneous socket connections
- Can be used to store files for serving over the network.
- Compatible with the Arduino Duemilanove (168 or 328), Uno as well as Mega (1280/2560).
- Can be accessed using the Mini SD TF library.
- The current shield has a Power over Ethernet (PoE) module designed to extract power from a conventional twisted-pair Category 5 Ethernet cable.
- IEEE802.3af compliant
- Low output ripple and noise (100mVpp)
- Overload and short-circuit protection
- 1500V isolation (input to output)