6 PIN 128*64 OLED 0.96” BLUE-YELLOW
- Resolution: 128*64
- Driver IC: SSD1306
- Visual angle>160
- Input voltage: 3.3V to 5V
- Power: 0.04W
- Pixel color: Yellow(16 Rows) and Blue
- No backlight, OLED self light
- Communication via I2C
- Works with ESP8266, Arduino, Raspberry Pi, 8051, MSP420, STM32
- Module volume: 27*27*4.1mm
- Working temperature: -30 degree to 80 degree
- Configured for SPI protocol and can be easily changed to IIC
4 PIN 128*64 OLED 0.96” BLUE
- Super high brightness and high contrast
- Driver IC: SSD1306
- Input voltage: .3v to 6 v
- Ultra-wide viewing angle >160 degree
- Low power consumption with 0.04 W
- Support wide range of Voltage: 3.3V to 5V
- OLED self-lights, no backlight required
- Fully compatible with Arduino
- Communication via IIC, only two I/O ports
- Working temperature: -30 degree to 80 degree
- Dimension: 27*27*4.1mm
- Supported platform: Arduino, 51 series, MSP430, SCR chips
- No font is required, software takes the word MODULO
4 WIRE RESISTIVE TOUCH SCREEN MUX BREAK OUT BOARD
5 Channel Infrared Reflective Sensor promixity sensor
- High-Quality Tracker Sensor
- The module is a convenient carrier for eight IR emitter and receiver pairs evenly paced.
- Distance between each IR Sensor: 15mm
- Uses 5 sensors for best resolution
- Great useful in building fast line following and grid navigating robots
- Comes with easy to use digital outputs with a direct connection to microcontrollers
- The array has mounting holes of 3mm diameter for easy mounting
- Status LED on each sensor for the detection of black line
USBASP PROGRAMMER
- No special USB controller required
- Programming speed is up to 5Kbytes/sec
- Working platform: Linux, Windows, Mac OS X
- Allows to read or write the microcontroller EEPROM, firmware, fuse bits, and lock bits
- No special controllers or SMD components are needed.
- Target is supported by the SCK option with a low clock speed (<1.5MHz)
- Programming status and Bus status are easily identified
- The easy interface is achieved by Header pins for various ISP header pins
- Dimension: 63.3*20.5*10.5mm
- Weight: 15gm
NOKIA DISPLAY MODULE
- Display technology: dot matrix LCD
- MCU interface: SPI
- Screen size: 1.5 inch
- Resolution: 84*48 pixels
- Operating voltage: 2.7v-3.3v
- Operating current: 50mA
- Current consumption: 6mA
- Consist of a Philips PCD8544 interface chip for easy interfacing
- Support decent graphics of bitmap images
- Available in green and blue backlight
- Viewing angle: 180 degree
- supports different types of MCU, such as Arduino, AVR, SPI, M, CS51
- Transfer rate up to 4Mbps, can full speed write data without waiting time
- Dimension:10.16*7.62*1.27cm
- Weight: 10gm
Solar Panel 6V 200mA
- Polycrystalline solar cell
- Max output power: 1.1W
- Max working voltage: 6.6V
- Max charging current: 110mA
- Min output power: 0.6W
- Min working voltage: 6V
- Min charging current:200mA
- Small Epoxy Solar Panels are simple to install or add to your existing product
- Construction requires no frame or special modifications
- Small space required for installation.
- Has 2 to 3 times the power of amorphous thin-film solar panels
- Ready to use, they require no frame or special modifications.
- For connection, just solder or crimp to the copper tape.
- Laser cut to proper size and encapsulated in special sun and weather resistant materials;
- Weight 33 Gms
12v 200mA Solar panel
- Output voltage：12V
- Output current: 200mA
- Service life: more than 5 years
- High transfer efficiency
- Non-pollution and reproducible
- 2.4-watt polycrystalline solar panel
- High conversion speed, high-efficiency output.
- Excellent low light effect.
- High transmittance tempered glass.
- Small Epoxy Solar Panels are simple to install or add to your existing product.
- Construction requires no frame or special modifications
- Small space required for installation.
- Has 2 to 3 times the power of amorphous thin-film solar panels
- Ready to use, they require no frame or special modifications.
- For connection, just solder or crimp to the copper tape
- Size: 213 x 92mm
- Weight：70g
HC-06 4Pin Bluetooth Module Without Reset Switch
- Working current: matching for 30 mA, matching the communication for 8 mA.
- Dormancy current: no dormancy.
- Used for a GPS navigation system, water, and electricity gas meter reading system.
- With the computer and Bluetooth adapter, PDA, seamless connection equipment.
- Bluetooth module HC-08 Master and slave Two in one module.
- Use the CSR mainstream Bluetooth chip, Bluetooth V2.0 protocol standards.
- Potter default rate of 9600, the user can be set up.
- Bluetooth protocol: Bluetooth Specification v2.0+EDR
- Speed: Asynchronous: 2.1Mbps(Max) / 160 kbps, Synchronous: 1Mbps/1Mbps.
- Security: Authentication and encryption.
- Profiles: Bluetooth serial port.
