Showing 1–12 of 245 results

WS2812 LED BREAKOUT BOARD

  • Input Voltage: -0.5~VDD+0.5V
  • Supply voltage: 5v
  • Operating voltage: 4v -7v
  • Integrating control circuit and RGB chip
  • Built-in signal reshaping circuit
  • Built-in electric reset circuit and power lost reset circuit
  • 256 brightness and 16777216 colour display
  • Viewing angle: 120 degree
  • Cascading port transmission signal
  • Red Vf: 1.8~2.2V
  • Green Vf: 3.0~3.2v
  • Blue Vf: 3.2~3.4V
  • Red Wavelength: 620~630 nm
  • Green Wavelength: 515~530 nm
  • Blue Wavelength: 465~475 nm
  • Red luminous intensity(20mA): 550~700mcd
  • Green luminous intensity(20mA): 1100~1400mcd
  • Blue luminous intensity(20mA): 200~400mcd
  • Dimension: 1.8*1.3*0.8mm

TB6560 4 Axis Stepper Motor Driver

  • Driver Chip: TB6560AHQ
  • Operating Voltage: 10-35V
  • Nominal Voltage: 24V
  • Stepper motor drive current: 1.5A - 3A/phase
  • With the large heat sink to ensure good heat dissipation
  • Double-pole constant flow PWM actuation output
  • 6N137 high-speed OptoCoupler, to ensure a high speed without stepping out.
  • Compatible Stepper motors: 2/4 Phase, 4/6/8 leads stepper motors within 3.5A
  • 1 - 1/16 micro step setting - higher accuracy, smoother operation
  • Full closed-type optical isolation to protect the user's computer and equipment
  • Professional design, two-stage signal processing, super anti-jamming
  • Bipolar constant current chopper drive motor low-speed non-creeping phenomenon, noise, non-resonant region
  • Four input control
  •  

4-axis Flight Control Sensor HMC5883L BMP085 MWC GY-651

  • Model: GY-651
  • Use the chip: HMC5883L + BMP085
  • Power supply:3-5v (internal low dropout regulator)
  • Size: 13.5mm * 15.8mm (pin spacing standard 2.54mm)
  • Communication modes: standard IIC communication protocol
  • Magnetic field range: ± 1.3 to ± 8.1 gauss
  • Pressure range: 300-1100hPa
  • Chip 12bit AD converter, 16-bit data output Machine welding process to ensure quality
  • Size: 18mmx14mm

Infrared Ir Obstacle Avoidance Detector Sensor Module Adjustable 2-180cm

  • Power requirements: 5 VDC
  • Communication: Digital High/Low Output
  • A variety of welding methods, vertical and horizontal, to expand the scope of application
  • Add precision potentiometer to adjust infrared 38KHz detection range
  • Sensor detection with enabling the port, convenient signal line as bus application line
  • Power-on enable port default level, the sensor enables the detection output signal
  • Detection range up to 1.2 meters
  • Software enhancement, setting can avoid infrared light interference of the same module or other kinds of infrared remote control devices
  • Working condition of each module recorded with EEPROM, reduce the probability of mutual interference of the same paragraph to 1%
  • Signal low output
  • Pin SIP header, applied in breadboard or through-hole project
  • On-board set jumper JP, the signal output has a latch function when shorted, otherwise, it is jog output
  • Operating temperature: 32 to 158 ° F (0 to +70 ° C)
  • Size: 2.4cm × 2.8cm

Leap Motion Controller

  • Power supply: 5V DC via USB connector (minimum 0.5A)
  • Data connection: USB 2.0
  • Interaction zone: Depth of up to 60cm (24”) preferred, up to 80cm (31”) maximum;
  • 140×120° typical field of view.
  • 3 LEDs spaced on either side and between the cameras, baffled to prevent overlaps.
  • Construction: Aluminium and scratch-resistant glass
  • Operating temperature: 32º to 113º F (0º to 45ºC)
  • Storage temperature: 14º to 122º F (-10º to 50º C)
  • Relative Humidity: 5% to 85% (non-condensing)
  • Two 640x240-pixel near-infrared cameras; spaced 40 millimetres apart infrared-transparent window, operate in the 850 nanometre +/-25 spectral range; typically operates at 120Hz; capable of image capture within 1/2000th of a second.
  • Highly accurate hand and finger tracking with near-zero latency
  • 135° field of view extending above the device
  • Orion SDK compatible with Windows 7 or newer
  • Updated V4 tracking

Bluetooth TTL HC05 HC06 Compatible Module

  • Bluetooth protocol: Bluetooth Specification v2.0+EDR
  • Frequency: 4GHz ISM band
  • Profiles: Bluetooth serial port TTL out
  • Sensitivity: ≤-84dBm at 0.1% BER
  • Modulation: GFSK(Gaussian Frequency Shift Keying)
  • Security: Authentication and encryption
  • Working temperature: -20 ~ +75 Centigrade
  • Power supply: +3.3V-5V DC 50mA
  • Profiles: Bluetooth serial port
  • 3 mm screw drive hole, easy to mount it on somewhere
  • UART interface with programmable baud rate
  • Push switch for issuing AT command
  • VCC GND OUT uses 2.54mm standard pins to ease the connections.
  • 2 No LED for Communication and Status
  • With integrated antenna
  • With edge connector
Has output status indication led, when output high TTL LED off, and vice versa

HC-05 Bluetooth Bee Master BEE05

  • Power supply: 3.3V
  • A power supply of more than 3.3V will destroy the module.
  • Paring user’s name: HC-05
  • Default baud rate: 38400
  • Default slave model
  • Default pairing password: 1234
  • This module was designed for XBEE so it’s compatible with the XBEE expansion base. This module was designed for XBEE so it’s compatible with the XBEE expansion base.
  • It can be used for an MCU system whose voltage is 3.3V.
  • Users can set master-slave model, baud rate, paring password, and user’s information by AT command.
  • Bluetooth adapter pairs with Bluetooth Bee salve device.
  • With an efficient onboard antenna, the exposed antenna qualifies the transmit signal and makes it farther.
  • Dimension: : 3.3 x 2.5 x 0.9 cm
  • Weight: 5g

BeagleBone Rev C with 4GB Flash Memory

  • Beaglebone black is a development kit based on an AM3359 processor which integrates an ARM Cortex A8 core and has abundant peripheral devices.
  • The beagle bone rev is designed to satisfy the different requirements of various fields including game devices, home, industrial automation, and consumer medical devices.
  • It comes with a 4GB flash memory and is preloaded with Debian Linux.
  • Beaglebone black provides lots of expansion interfaces such as Ethernet, USB Host, OTG, TF card, serial, HDMI D type, I2C, SPI, PWM, and LCD.

JQ6500 Voice Sound Module 16Mbit Music MP3 Play MCU Serial Control Module UART SPI Flash

  • Input voltage: Power supply is at 3.2V-5V, 4.2V Power supply is the best
  • Rated current: 20ma
  • Standard DIP16 package.
  • 30 level adjustable volume, 10 adjustable EQ
  • Working temperature: -40~70°C
  • Humidity: 5%~95%
  • Support sampling rate (KHz): 8 / 11.025 / 12/16 / 22.05 / 24/32 / 44.1 / 48
  • 24-bit DAC output,
  • dynamic range support 90dB, SNR support 85dB
  • Full support FAT16, FAT32 file system, the largest support 32G TF card, support 32G U disk, 64M bytes NOR FLASH
  • A variety of control mode, parallel port control mode, serial port mode, AD button control mode
  • The audio data sorted by folder, up to 100 folders, every folder can be assigned 1000 songs
  • You can plug in SPI flash, connect the computer can display spi flash letter to update the content;
  • Controlled through the microcontroller serial port to play the specified music;
  • Can be interrupted: that is, in the process of playing, press the button will interrupt the current state to perform the new;
  • MP3 file format: supports all bit rates 11172-3 and ISO13813-3 layer3 audio decoding

AMS1117 5V POWER SUPPLY MODULE

• Input: DC 6.5V – 12V (input voltage must be more than the output voltage (more than 1V)) • Output: 5V, 800mA (load current cannot exceed 800mA) • Onboard AMS1117 chip. • Onboard power indicator to indicate power is turned on: Red LED. • Output voltage interface, connection to facilitate the experimental. • Specially designed two pin mounting holes, can be directly fixed on the whole expansion board for experiments. • Small Compact Size, 4Pin Type, Breadboard Friendly. • 2P single row pin input and output for easy connection • Dual-panel design, the layout is nice

KY-036 Metal Touch Sensor Module

  • Main chip: LM393
  • Working voltage: for DC 5V
  • Single-channel signal output
  • Low-level output signal used for human body touch sensor alarm
  • Adjustable sensitivity
  • Pin Connector to board: 4 Pins
  • Dimensions: 43 x 16 x 15 mm / 1.69 x 0.63 x 0.59 inch
  • Single-channel signal output
  • Low-level output signal used for human body touch sensor alarm
  • Adjustable sensitivity
  • Long life
  • High reliability

3W LED Module High-Power with PCB Chassis for Arduino STM32 AVR

₹30.00 inc. GST
  • Type: LED High Power Board
  • Forward voltage: 3.3 – 3.6 V
  • Reverse voltage: 5V
  • Power: 3W
  • Viewing angle: 180°
  • Mainly Compatible with: Arduino
  • 3W LED High Power Board for Indoor / Outdoor Display
  • Colour temperature: Warm White 3000-3200K / white 6000-6500K
  • Forward current: 700MA
  • Luminous flux: White 180-200LM (lumens) , Red 90-100LM (lumens) , Green 80-90LM (lumens)
  • Long life
  • small size
  • Material: PCB