434MHz/315Mz TX & RX
Transmitter
- Working voltage: 3V - 12V for max. power use 12V
- Working current: max Less than 40mA max , and min 9mA
- Modulation mode: ASK
- Working frequency: 433MHz
- Transmission power: 25mW
Receiver
- Working voltage: 5.0VDC
- Working current:≤5.5mA max
- Modulation method: OOK/ASK
- Working frequency: 433.92MHz
- Bandwidth: 2MHz
- Sensitivity: excel –100dBm (50Ω)
- Transmitting velocity: <9.6Kbps (at 315MHz and -95dBm)
BMP280 Pressure Sensor module High Precision Arduino
- Chip:BMP280
- Operating Voltage: 1.71V to 3.6V
- Communication method: Standard IIC/SPI communication protocol
- Pin pitch: 2.54mm
- Operating Temperature: -40 to +85 deg. Celsius
- Operating Pressure: 300 hPa to 1100 hPa
- Peak current: 1.12mA
- Current consumption: 2.7µA @ 1 Hz sampling rate
- Accuracy between( 700 to 900hPa and 25 to 40 deg. C): ±0.12hPa and ±1.0m
- Package 8-pin LGA metal-lid
- Relative accuracy(950 … 1050hPa @25°C): ±0.12 hPa, equiv. to ±1 m
- RoHS compliant, halogen-fre
- Module size: 11.5mm*15mm
Delay Timer Switch Adjustable 0-10sec With NE555 Electrical Input 12V 10A
- Module based on the NE555 chip.
- Input voltage: DC 12V
- Adjustable time: 0-10 s
- AC Control voltage: 250V/max. 10A
- DC Control Voltage: 30V/max. 10A
- load: 2200W
- Precision Pulse Generation / Timing.
- Monostable Operation.
- Standby no power consumption
- Excellent temperature stability of 0.005%/°
- Time can be adjusted by a potentiometer, the default is 0-25 seconds
Double Analog Potentiometer Module With Slide Potentiometer Slip Adjustable Resistance For Arduino
- Dual analogue output, output 0-VCC analogue voltage signal.
- Voltage: 3.3V, 5V.
- Port: Analog.
- Resistance: 10K.
- Slide potentiometers module
- Two analogue outputs, analogue outputs 0-VCC voltage signals
- Stable and reliable performance with high-quality sliding appliances
- Platform: Arduino, MCU, ARM, and other microcontroller platforms
- Application: Raspberry Pi projects, DIY projects, Arduino projects.
- Dimensions: 91 x 21 x 30 mm
- Weight: 18 gm.
Protosheild For Arduino
- Standard 0.1"x0.1" prototyping grid with big pads
- Comes with Stacking headers and plain header, choose whichever you want when soldering together
- IC pattern for adding DIP ICs up to 20 pins
- Power rails down the middle and sides
- Reset button and an extra general use button
- 2 3mm general use LEDs, red and green, as well as 2 matching resistors
- A pass-thru ICSP stacking header so you can stack any kind of shield on top, and/or use an AVR programmer
- A surface-mount chip area for up to 14 SOIC size parts
- Compatible with tiny breadboards
- Every pin is brought out
- Gold plated pads
- 2 x 0.1uF capacitors on either side for extra power stability
Attiny 5 Version 1
- High Performance, Low Power AVR® 8-Bit Microcontroller
- Non-volatile Program and Data Memories
- 8K Bytes of In-System Programmable Program Memory Flash
- Endurance: 10,000 Write/Erase Cycles
- 512 Bytes In-System Programmable EEPROM
- Endurance: 100,000 Write/Erase Cycles
- 512 Bytes Internal SRAM
- Peripheral Features
- High-Frequency PWM Outputs with Separate Output Compare Registers
- USI – Universal Serial Interface (12C, SPI, 1-wire) with Start Condition Detector
- 10-bit ADC
- Single-Ended Channels
- 2 Differential ADC Channel Pairs with Programmable Gain (1x, 20x)
- Speed Grade: 0 – 10 MHz @ 2.7 – 5.5V, 0 – 20 MHz @ 4.5 – 5.5V
- Low Power Consumption
- Active Mode:1 MHz, 1.8V: 300 µA
5V-30V Delay Relay Timer Module Trigger Delay Switch Micro USB Power Adjustable Relay Module
- Time can be adjusted by potentiometers
- With MicroUSB 5.0V power input, it is very convenient to use.
- 5V --30V ultra-wide supply voltage.
- External triggering and on-board buttons are two trigger modes.
- With relay suction indicator.
- The anti-interference ability is strong, and the relay will not misbehave under all kinds of disturbances, so it is suitable for industrial control.
- Module can be controlled: 10A 250VAC (AC), 10A 30VDC (DC) below load.
- With Relay follow current protection.
- • Size: 5.4 * 1.9 * 1.8cm
Electrobot Micro HDMI to HDMI Cable (Compatible with Raspberry Pi 4)
A4988 STEPPER MOTOR DRIVE CONTROLLER BOARD
- Operating voltage supply: 8 V to 35 V
- Continuous current per phase: 1 Amp
- Maximum current per phase: 2 Amp
- Minimum logic voltage: 3V
- Maximum logic voltage: 5.5V
- Microstep resolutions: Full, 1/2, 1/4, 1/8, and 1/16
- Compact size, easy to install and use.
- All jumpers hit the ON position to indicate 16 subdivisions (4988) or 32 subdivisions (8825).
- Jm connection motor; Jv Connects 5V and 12V-24V Power Supply.
- E /S /D /G of Jc corresponds to Enable /Step /Dir /Gnd driving signal output on the connection respectively.
