USB TO RS-485 CONVERTER
- Small and compact size
- Baud rate:75 bps-115200bps, up to 6Mbps
- Communication distance:1200m
- Support USB 2.0 standard
- Self-powered by USB bus
- Working temperature:-40degree - +85 degree
- RS-232 serial port transmission speed of max 115.2Kbps
- Supports full handshake protocol, full-duplex data operating mode
- Directional control: Uses automatic data flow control technology, automatic identification and control of data transfer direction Load capacity: support multipoint
- Interface protection: TVS tube protection, USB self-recovery protection
- Screw Terminal Connector for easy connection
- The module requires no external power, it takes power from the USB port
- Supported Systems: Windows XP, Vista, Windows 7, Linux, macOS, and
- Dimension:6.1x1.6x1.3cm
USBASP PROGRAMMER
- No special USB controller required
- Programming speed is up to 5Kbytes/sec
- Working platform: Linux, Windows, Mac OS X
- Allows to read or write the microcontroller EEPROM, firmware, fuse bits, and lock bits
- No special controllers or SMD components are needed.
- Target is supported by the SCK option with a low clock speed (<1.5MHz)
- Programming status and Bus status are easily identified
- The easy interface is achieved by Header pins for various ISP header pins
- Dimension: 63.3*20.5*10.5mm
- Weight: 15gm
USB AVR ISP 10 Pin Programmer | ATmega8 USB Programmer
- Allows you to read or write the microcontroller EEPROM, firmware, fuse bits and lock bits
- Support for Linux, Mac OS X and Windows XP,7,8
- 5 KB/sec maximum write speed
- Software controlled SCK option to support targets with low clock speed (< 1.5MHz)
- 10 pin ISP interface
- Works under multiple platforms. Linux, Mac OS X and Windows are tested.
- Software controlled SCK option to support targets with low clock speed (less than 1.5MHz).
- 6 Pin Adapter board along with the programmer for Standard ISP connections.
- B-type USB Connector for power.
- Separate Two Different leds for power & programmer status.
USB TO SERIAL CP2102 CONVERTER
- Reliable and stable device
- Baud rate:300bps-1Mbps
- Supports Windows, Linux &Mac
- Compliant withUSB2.0 at a full-speed 12Mbps
- Self-power :3.0 to 3.6v
- USB bus power:4.0 to 5.25v
- Supports all handshaking and modem interface signal
- Standard USB type A male and TTL 6pin connector.
- 6pins for 3.3V, RST, TXD, RXD, GND & 5V.
- All handshaking and modem interface signals.
- Byte receives buffer; 640 bytes transmit buffer.
- Hardware or X-On/X-Off handshaking supported.
- Event character support Line break transmission.
- USB suspend states supported via SUSPEND pins.
- Temperature Range: -40 to +85.
- Dimension: 42mm X 15mm.
PL2303 USB TO TTL CONVERTER
- USB specification 2.0 compliant with full-speed 12Mbps.
- Operation Level-Digital 5V
- Power Supply-External 5V
- Standard USB type A male and TTL 6pin connector.
- 6 pins for 3.3V, RST, TXD, RXD, GND & 5V.
- All handshaking and modem interface signals.
- Baud rates: 300 bps to 1.5 Mbps.
- Byte receives buffer; 640 bytes transmit buffer.
- Hardware or X-On/X-Off handshaking supported.
- Event character support Line break transmission.
- USB suspend states supported via SUSPEND pins.
- Supports Windows 98SE, 2000, XP, Vista, Window7, Mac OS 9, Mac OS X & Linux 2.40.
- Simple serial communication.
- Router or ADSL firmware upgrade.
- Easy to use, RX to the MCU's TX; TX to the MCU's RX. and then connected to the GND. Without having to use the MAX232 conversion.
AVR ISP 10 Pin to 6 Pin Adapter Board
MAX3232 RS232 TO TTL CONVERTER
- Chip model: MAX3232 IC
- Supply voltage: 3V -5V
- Maximum Baud Rate: up to 120kbps
- High speed, replaceable MAX232 based.
- Working mode: Full duplex
- Supports microcontroller UARTs – 5V TTL signal levels.
- Low current status LED(s)
- Very low power consumption
- Optional onboard PSU for internal/external use for a quick start out of the box.
- Power can be routed to pin 9 (if required) on the RS232 connector – useful for specific
- Operating temperature: -40 degree to +85 degree Celsius
- Dimension: 16.22*10.3*3.5mm
- Weight: 1gm