IMAX B6-AC Lipo NiMH Battery Charger/Discharger 1-6 Cells
- AC Input Voltage: 100V ~ 240v or 12V DC input
- Current: 2.5A Max.
- Max Charge: 50W
- Max Discharge: 5W
- Charge Current Range: 0.1A ~ 6.0A
- Discharge Current Range: 0.1~1.0A NiMH/NiCd Cells, 1~15A LiIon/LiPoly Cells 1~6A Pb
- Plug Type: Female End Type: IEC(To Charger)
- Plug Type. Male End Type: EU plug (To Power Distribution Board).
- The cables come with a fitted fuse.
- Microprocessor controlled
- Li-ion, LIPO, and LiFe are capable
- Input voltage monitoring. (Protects car batteries at the field)
- Battery break-in and cycling feature
- Data storage (Store up to 5 packs in memory)
- Internal resistance checker to see pack health
- Delta-peak sensitivity
- Individual cell balancing
- EU Plug to IEC C13 which is used in devices such as ac adapters, digital cameras, camcorders, monitors, printers, Direct TV and more!\
- Dimensions: 135 x 144 x 36mm
- Weight: 632g
IMAX B6 DIGITAL RC LIPO NiMH BATTERY BALANCE CHARGER
- Input Voltage: 11V to 18V
- Battery Voltage: 2V to 20V
- Power Max Charge: 50W – Max
- Discharge: 5W
- Charge Current Range: 0.1 to 5.0A
- Discharge Current Range: 0.1~1.0A NiMH/NiCd Cells, 1~15A LiIon/LiPoly Cells, 1~6A Pb
- Microprocessor controlled
- LiIon, LiPoly, and LiFe are capable
- NiCad and NiMH are capable
- Large range of charge currents
- Storage charge function
- Time limit function
- Delta-peak sensitivity
- Individual cell balancing
- Battery break in and cycling.
- Input voltage monitoring (Protects car batteries at the field)
- Data storage (Store up to 5 packs in its memory
- Dimensions: 133x87x33m
- Weight 277g
Solar Charge Controller 12v/24v 40A
- High efficiency:Â your batteries are charged quickly.
- Capacity for solar panel configurations of up to 3600 Wp.
- Suitable for AGM, gel, wet and Mastervolt Lithium Ion batteries.
- Fast and flexible setting of battery type.
- Battery temperature sensor for long lifespan.
- Automatic 12 V/24 V/48 V detection.
- Switchable output.
- Noiseless operation.
- LCD display.
- Fully protected against overtemperature, overload, high/low battery voltage, high/low PV voltage, short circuit and reverse polarity.
Solar Charge Controller 12v/24v 10A
Lipo Battery Charger B3
- Input voltage: AC 110V-240V, 50~60Hz
- Charge Current: 1.2A Max
- Cell Cut Off Voltage: 4.2V ± 0.02V
- Circuit Power: 11W ± 10%
- Balance charge current: 850mA
- Display: Green & Red LED
- Built-in power supply
- Case: Plastic
- Max charge power: 10W
- Only charge for 2~3 series LiPo battery
- Automatic charge start
- Simple, reliable, and safe to use
- Dimensions: 88x57x35mm
- Weight:103gm
IMAX B3 Charger
- Input voltage: AC 110V-240V, 50~60Hz
- Charge Current: 1.2A Max
- Cell Cut Off Voltage: 4.2V ± 0.02V
- Circuit Power: 11W ± 10%
- Balance charge current: 850mA
- Display: Green & Red LED
- Built-in power supply
- Case: Plastic
- Max charge power: 10W
- Only charge for 2~3 series LiPo battery
- Automatic charge start
- Simple, reliable, and safe to use
- Dimensions: 88x57x35mm
- Weight:103gm
12V / 2A Battery Charger
- This is a durable product with a 6-month warranty.
- The adapter is easy to use.
- It comes with a long wire.
- Wide input voltage range (100VAC-280VAC).
- Very low no-load power consumption.
- Very low ripple & noise output for device safety.
- Protections against- under-over voltage/ overload/ short circuit with auto-restart on fault removal.
- Thermal shut down (140°C) with auto-restart on cold condition.
- Soft start & low inrush current.
- Isolation up to 3kv for 5sec.time period.
- High operating ambient temperature up to 60°C.
- Highly efficient, compact, durable and long life.
TP5100 4.2v 8.4v Single Double Lithium Battery Charge Management Li-ion Battery Compatible 2A Charging Board
- Input voltage: 5-15V DC power supply.
- Charge status: full and unloaded blue lights, charging red.
- Double 8.4v / 4.2v lithium rechargeable single .
- Programmable charge current. 0. 1A-2A .
- Programmable steady precharge current 10% -100%.
- Wide operating voltage, maximum reach I8V.
- Red and green LED charge status indicator.
- Chip temperature protection, overcurrent protection, under voltage protection.
- Battery temperature protection, reverse battery shutdown, short circuit protection.
- Switching frequency 400Khz, usable inductance 20uH and more.
- PWR_ON Power battery for switching control.
Dual USB 5V 1A 2.1A Mobile Power Bank Battery Charger
- Micro USB input: 5V 1A
- Charging voltage input: 5V-6V 1A.
- Step-up voltage output: 5V 1A/2.1A (Dual output, Total 2.5A).
- USB Output: 5V 2.1A / 5V 1A(Dual USB interface)
- Charging display: intelligent digital display
- Batteries Type: liquid lithium-ion batteries (18650)
- Best for Arduino, DIY Kits, Power bank, etc.
- Protection circuit: Overcharge protection: 4.250V Overcharge protection release: 4.100V.
- Protection circuit: Over-discharge protection: 2.900V Over-discharge protection release: 3.000V.
- Idle time before LCD switch off 60secs.
- Screen size:27mm x 17mm
- Dimension: 57mm x 28mm
3S BMS BOARD 25A
- Charging Voltage: 12.6V DC CC/CV
- Balance Voltage for Single Cell: 4.2V
- Max Continuous Charge/Discharge Current: 25A
- Overcharge voltage range: 4.25-4.35v + 0.05v.
- Over discharge voltage range: 2.3-2.7v + 0.05v.
- Operating current: 0 – 25A.
- Operating temperature: -40 – +50℃.
- Instantaneous current: 35 – 40A.
- Storage condition: -40 – +80℃.
- Quiescent current: less than 30uA.
- Balance current: about 40 – 50mA.
- Effective life: more than 30000 hours.
- Internal resistance: less than 100m ohms.
- Short-circuit protection: protection, delayed self-recovery.
USB Charger Doctor
- Display data: Voltage Current
- Operating Voltage: 3.5 to 7 V
- Maximum Current: 3 A ( accuracy of 0.4% )
- Battery Capacity (0-99999mah)
- Working time (0-99Hour)
- Charger voltage compliance DC 5V
- Resolution : Voltage 10mV current 1mA
- Error : voltage <± 1% current <± 2%
- USB Plug: 13mm / 0.5"
- RTZ, Reset button, press it three seconds will Reset
- The working time and Capacity have a Memory function when power is off.
- Compact and easy to carry, no additional power supply, plug, and play
- Detect any USB charger such as PC USB, home charger, car charger
- Easily measures the output voltage of the USB port and the device operating current or load voltage
- Dimensions: 21mm x 53mm x 15mm
- Weight: 16.2gm