Showing 1–12 of 173 results

Stepper Motor NEMA 34 122 kg-cm Hybrid Bipolar

9,000.00 inc. GST
  • Rated Voltage:4.08V
  • Phase: 2
  • Current/ phase: 4A
  • Holding Torque: 122 kg-cm
  • Number of Leads: 4
  • Step Angle: 1.8°
  • Step Angle Accuracy: ±5% (full step, no load)
  • Resistance Accuracy: ±10%
  • Inductance Accuracy: ±20%
  • Frame Size: 85x85mm
  • Shaft Length: 37mm
  • Shaft Diameter: 13mm
  • Long-lasting life
  • Low cost for control achieved
  • High torque at startup and low speeds
  • Ruggedness
  • Simplicity of construction
  • Can operate in an open-loop control system
  • Low maintenance
  • Less likely to stall or slip

UNITE DC 48V 750W BM1418ZXF Brushless Gear Motor

8,800.00 inc. GST
  • Rated Output Power: 750W
  • Rated Voltage: 48V DC
  • Speed after Reduction: 480 RPM
  • Rated Speed: 2800 RPM
  • Gear Ratio: 1:6
  • Full Load Current: 20A
  • No Load Current: 5A
  • Rated Torque: 15.36 N.m
  • Load Capacity: Upto 350 KG.
  • Motor Dimension : 24 x 14x 14cm
  • Application - Small and Medium size E-Tricyc

Leadshine DMA860H

8,500.00 inc. GST
  • Input voltage: Up to +80VAC or +110VDC.
  • Output current Up to 7.2A.
  • Pulse input frequency up to 300 KHz.
  • Automatic idle-current reduction.
  • Over-voltage, over-current protection.
  • Suitable for 2-phase and 4-phase motors.
  • Support PUL/DIR and CW/CCW modes.
  • Operating Temperature : 70 C.
  • High performance, cost-effective
  • Self-adjustment technology
  • Pure-sinusoidal current control technology
  • TTL compatible and optically isolated input
  • 16 selectable resolutions in decimal and binary, up to 51,200 steps/rev
 

UNITE DC 48V 350W BM1418ZXF Brushless Gear Motor

8,100.00 inc. GST
  • Model: BM1418ZXF.
  • Rated Output Power: 350W.
  • Rated Voltage: 48V DC.
  • Speed after Reduction: 480 RPM.
  • Rated Speed: 2800 RPM.
  • Gear Ratio: 1:6.
  • Full Load Current: 9.4A.
  • No Load Current: 2.8A.
  • Rated Torque: 7.2 N.m.
  • Phase Angle : 120 degrees
  • Application: Small and Medium size E-Tricycle.

Stepper Motor NEMA 34 46 kg-cm Hybrid Bipolar

6,899.00 inc. GST
  • Rated Voltage:4.2V
  • Current/ phase: 4A
  • Inductance/ phase: 7.3mH
  • Resistance/ phase: 0.87ohms
  • Holding Torque: 46 kg-cm
  •  Number of Leads: 4
  • Step Angle: 1.8°
  • Step Angle Accuracy: ±5% (full step, no load)
  • Resistance Accuracy: ±10%
  • Inductance Accuracy: ±20%
  • Frame Size: 85x85mm
  • Shaft Length: 32mm
  • Shaft Diameter: 12mm
  • They are high torque stepper motors.
  • Input pulse decides the rotation angle of the motor.
  • High accuracy of around 3 to 5% a step.
  • Provides good starting, stopping and reversing

48v 500W BM1418ZXF Brushless Motor

6,800.00 inc. GST
  • Rated Operating Voltage: 48V DC.
  • Rated Power: 500W.
  • Rated Speed: 2800 RPM.
  • No Load Speed: 3100 RPM.
  • Full Load Current: 13.4A.
  • No Load Current: 4.0A.
  • Rated Torque: 1.7N.m.
  • Efficiency: >75%.
  • Gear Speed: 400 RPM.
  • Gear Torque: 10N.m.
  • Gear Ratio: 6:1.

Leadshine DMA860E Stepper Motor Driver

5,700.00 inc. GST
  • Model: DMA860E.
  • Control Mode: Step & Direction.
  • Max Input Frequency: 200 kHz.
  • Input Voltage Range: 18 - 80 VAC / 24 - 110 VDC.
  • Suggested Power Supply Voltage Range: 36-90 VDC /24-60 VAC.
  • Number of DIP Switch Resolution Configurations: 16.
  • 16 selectable micro-step resolutions of 400-51,200 via DIP switches.
  • 8 selectable output current settings of 2.4 – 7.2A via DIP switches.
  • Logic Current Range: 7-16mA (10mA typical).
  • Logic Voltage Range: 4-5 VDC for pulse active high (default), or 0-0.5V for pulse active low.
  • Pulse enabled at: Rising edge.
  • Idle Current Percentage: 50 %.
  • Number of Digital Inputs: 3.
  • Step Width: 2,500 ns.
  • Minimal Direction Setup Time: 5,000 ns.
  • Isolation Resistance: 500M Ohm..
  • Ambient Temperature: 0-50°C.
  • Humidity: 40–95% RH.
  • Operating Temperature: 0-70°C.
  • Vibration: 5.9 m/s2 Max.
  • Motor auto-identification and parameter auto-configuration for optimal torque from wide-range motors.
  • Step & direction (PUL/DIR) and CW/CCW (via internal jumper set) control. Step & direction by default Multi-Stepping for smooth motor movement.
  • Opto Isolation for input control signals.
  • Soft-start with no “jump” when powered on.
  • Protections for over-voltage and over-current.
  • Dimension: 5.94 X 3.82 X 2.24 Inches.
  • Weight: 1.13 lbs.
   

Stepper Motor NEMA 34 68 kg-cm Hybrid Bipolar

5,549.00 inc. GST
  • Rated Voltage:4.2V
  • Current/ phase: 4A
  • Holding Torque: 68 kg-cm
  • Number of Leads: 4
  • Step Angle: 1.8°
  • Step Angle Accuracy: ±5% (full step, no load)
  • Resistance Accuracy: ±10%
  • Inductance Accuracy: ±20%
  • Frame Size: 85x85mm
  • Shaft Length: 32mm
  • Shaft Diameter: 12mm
  • Long-lasting life
  • Low cost for control achieved
  • High torque at startup and low speeds
  • Ruggedness
  • Simplicity of construction
  • Can operate in an open-loop control system
  • Low maintenance
  • Less likely to stall or slip

Leadshine DM320C

5,500.00 inc. GST
  • Supply voltage up to +30 VDC
  • Output current programmable, from 0.3A to 2.0A
  • Pulse input frequency up to 70 kHz
  • TTL compatible and optically isolated input
  • Automatic idle-current reduction
  • Suitable for 2-phase and 4-phase motors
  • Support PUL/DIR and CW/CCW modes
  • Over-voltage, over-current, phase-error protection
  • Anti-Resonance provides optimum torque and nulls mid-range instability
  • Self-test and Auto-configuration technology offers optimum responses with different motors
  • Microstep resolutions programmable, from full-step to 102,400 steps/rev
  • Support PUL/DIR and CW/CCW modes
  • Over-voltage, over-current, phase-error protection
  • Its unique features make the DM320C an ideal solution for applications that require low-speed smoothness

Stepper Motor NEMA 34 87 kg-cm Hybrid Bipolar

5,449.00 inc. GST
  • Rated Voltage:4.2V
  • Current/ phase: 5A
  • Holding Torque: 87 kg-cm
  •  Number of Leads: 4
  • Step Angle: 1.8°
  • Step Angle Accuracy: ±5% (full step, no load)
  • Resistance Accuracy: ±10%
  • Inductance Accuracy: ±20%
  • Frame Size: 85x85mm
  • Shaft Length: 32mm
  • Shaft Diameter: 12mm
  • They are high torque stepper motors.
  • Input pulse decides the rotation angle of the motor.
  • High accuracy of around 3 to 5% a step.
  • Provides good starting, stopping and reversing

Metal Gear Servo Motor GS-5515MG

4,900.00 inc. GST
  • Control System: Positive PWM control (1500 usec neutral)
  • Operation Voltage Range: 4.8V - 0V
  • Operation Temperature Range: -20 C - +60 degree C
  • Test Voltage:
  • Standing Torque@ 4.8V: 13kg-cm
  • Speed@ 4.8V : 0.31 sec / 60 at no load
  • Idle Current@ 4.8V: 250mA at stopped
  • Running Current@ 4.8V: 2000mA at no load
  • Standing Torque@ 6.0V: 15kg-cm
  • Speed@ 6.0V: 0.28 sec / 60 at no load
  • Idle Current@ 6.0V: 300mA at stopped
  • Running Current@ 6.0V: 2200mA at no load
  • Dead Band Width: 8 usec
  • Circle: 10000 times
  • Direction: Re-clock wise/ pulse travel 1500 to 1900 usec
  • Drive type: FET drive
  • Motor Type: Carbon brush
  • Size: 41.2*20.2*37.7 mm
  • Weight: 63g without splined horn
  • Ball Bearing: Double ball bearing
  • Gear Material: Metal gear
  • Case Material: Nylon plus fiber
  • Connector Wire Length: 300mm
  • Connector Wire Gauge: 22AWG heavy duty (Futaba universal)

FEETECH FT6560M 65kg Large Scale High Torque Servo

4,800.00 inc. GST
  • Model: FT6560M.
  • Operating Speed6.0v 0.15 sec/60°.
  • Operating Speed7.4v 0.13 sec/60°.
  • Stall Torque 6.0v 48 kg.cm.
  • Stall Torque 7.4v 62 kg.cm.
  • Motor: carbon.
  • Control Way: Digital.
  • Cable Length: 20cm.
  • Gear: 5 metal gears.
  • Bearing: 2BB.
  • Dead band: 4us.
  • Working frequency: 330hz.
  • Wire/Color: JR 265 mm/ -Brown +Red S Orange.
  • Dimensions: 65.8X30.2X57.4mm.
  • Weight: 200 g.