N20 Model – 500 RPM DC 12V Torque Gearbox Micro Gear Box Motor
- Reduction ratio - 1:30.
- Nominal Voltage - 6v
- Voltage Range - 3v to 12v
- RPM - 500
- No-load Current - 40mA
- Stall Current - 550mA
- Stall Torque - 400 g-cm
- Ideal for making robots
- Lightweight, high torque and low RPM.
- Fine craftsmanship, long-lasting, not easy to wear.
- Can easily mount a wheel on the motor’s output shaft.
N20 Model – 300 RPM DC 12V Torque Gearbox Micro Gear Box Motor
- Reduction ratio: 1:50.
- Nominal Voltage: 6v
- Voltage Range: 3v to 12v
- RPM: 300
- No load Current: 40mA
- Stall Current: 550mA
- Stall Torque: 700 g-cm.
- Ideal for making robots
- Lightweight, high torque and low RPM.
- Fine craftsmanship, long-lasting , not easy to wear.
- Can easily mount a wheel on the motor’s output shaft.
N20 Model – 40 RPM DC 12V Torque Gearbox Micro Gear Box Motor
- Reduction ratio: 1:380.
- Nominal Voltage: 6v.
- Voltage Range: 3v to 12v.
- RPM: 40.
- No-load Current: 40mA.
- Stall Current: 550mA.
- Stall Torque: 7500 g-cm.
- Ideal for making robots
- Lightweight, high torque, and low RPM.
- Fine craftsmanship, long-lasting, not easy to wear.
- Can easily mount a wheel on the motor’s output shaft
Leadshine DMA860E Stepper Motor Driver
- Model: DMA860E.
- Control Mode: Step & Direction.
- Max Input Frequency: 200 kHz.
- Input Voltage Range: 18 - 80 VAC / 24 - 110 VDC.
- Suggested Power Supply Voltage Range: 36-90 VDC /24-60 VAC.
- Number of DIP Switch Resolution Configurations: 16.
- 16 selectable micro-step resolutions of 400-51,200 via DIP switches.
- 8 selectable output current settings of 2.4 – 7.2A via DIP switches.
- Logic Current Range: 7-16mA (10mA typical).
- Logic Voltage Range: 4-5 VDC for pulse active high (default), or 0-0.5V for pulse active low.
- Pulse enabled at: Rising edge.
- Idle Current Percentage: 50 %.
- Number of Digital Inputs: 3.
- Step Width: 2,500 ns.
- Minimal Direction Setup Time: 5,000 ns.
- Isolation Resistance: 500M Ohm..
- Ambient Temperature: 0-50°C.
- Humidity: 40–95% RH.
- Operating Temperature: 0-70°C.
- Vibration: 5.9 m/s2 Max.
- Motor auto-identification and parameter auto-configuration for optimal torque from wide-range motors.
- Step & direction (PUL/DIR) and CW/CCW (via internal jumper set) control. Step & direction by default Multi-Stepping for smooth motor movement.
- Opto Isolation for input control signals.
- Soft-start with no “jump” when powered on.
- Protections for over-voltage and over-current.
- Dimension: 5.94 X 3.82 X 2.24 Inches.
- Weight: 1.13 lbs.
FEETECH FT6560M 65kg Large Scale High Torque Servo
- Model: FT6560M.
- Operating Speed6.0v 0.15 sec/60°.
- Operating Speed7.4v 0.13 sec/60°.
- Stall Torque 6.0v 48 kg.cm.
- Stall Torque 7.4v 62 kg.cm.
- Motor: carbon.
- Control Way: Digital.
- Cable Length: 20cm.
- Gear: 5 metal gears.
- Bearing: 2BB.
- Dead band: 4us.
- Working frequency: 330hz.
- Wire/Color: JR 265 mm/ -Brown +Red S Orange.
- Dimensions: 65.8X30.2X57.4mm.
- Weight: 200 g.
“FEETECH FS6535M 33KG High Torque Analog Servo FOR Large Scale Big RC Robot – FS6535M “
- Operating Voltage:4.8-6Volts
- Stalling torque: 27.5(kg-cm) @ 4.8V; 33(kg-cm) @ 6V.
- Stalling current: 3.8 A.
- No-load speed: 0.27±0.03(sec/60°).
- Direction: CCW.
- Operating Angle: 180degree.
- Required Pulse: 500us-2500us.
- Bearing Type: 2BB.
- Gear Type: Metal.
- Motor Type: Carbon.
- Wire length: 25cm.
- Rotation angle (standard) : CW 90±5°.
- Dimension: 65.8x30.4x57.6mm.
- Weight: 199g
FEETECH FT5335M 35kgcm Ultra-High-Torque, High-Voltage Digital Giant Servo
Stepper Motor NEMA 23 28 kg-cm Hybrid Bipolar
• Phase - 2 phase Bipolar
• Rated Voltage:4.8V
• Current/ phase: 3A
• Inductance/ phase: 7.5 mH (20% variance)
• Resistance/ phase: 1.6 Ohms (10% variance)
• Holding Torque: 28 kg-cm
• Number of Leads: 4
• Step Angle: 1.8°
• Step Angle Accuracy: ±5% (full step, no load)
• Resistance Accuracy: ±10%
• Inductance Accuracy: ±20%
• Frame Size: 85x85mm
• Shaft Length: 32mm
• Shaft Diameter: 12mm
• They are high torque stepper motors.
• Input pulse decides the rotation angle of the motor.
• High accuracy of around 3 to 5% a step.
• Provides good starting, stopping and reversing
• Supreme finish, Smooth surface, Long lasting life
• Can operate in an open loop control system
• High reliability
Stepper Motor NEMA 23 23 kg-cm Hybrid Bipolar
- Phase - 2 phase Bipolar
- Rated Voltage:2.55V
- Current/ phase: 3.5A
- Inductance/ phase: 2.8 mH (20% variance)
- Resistance/ phase: 0.73 Ohms (10% variance)
- Holding Torque: 23 kg-cm
- Number of Leads: 4
- Step Angle: 1.8°
- Step Angle Accuracy: ±5% (full step, no load)
- Resistance Accuracy: ±10%
- Inductance Accuracy: ±20%
- Frame Size: 85x85mm
- Shaft Length: 32mm
- Shaft Diameter: 12mm
- They are high torque stepper motors.
- Input pulse decides the rotation angle of the motor.
- High accuracy of around 3 to 5% a step.
- Provides good starting, stopping and reversing
- Supreme finish, Smooth surface, Long lasting life
- Can operate in an open loop control system
- High reliability
XB NEMA 34 (86mm-S) Coupling 12.7x8mm
- Material: Aluminum alloy hubs and elastomeric polyurethane spider.
- Product Type: Clamp-style jaw coupling without keyway.
- Large Bore Diameter: 12.7mm
- Small bore diameter:8mm
- Number of Screws: 2 each.
- Angular Misalignment: +/-1°.
- Parallel Misalignment: +0.20mm/-0.20mm .
- Maximum Rotational Speed: 6500RPM.
- Suitable for Nema 23 Stepper Motor or for any motor/rod having an 12.75mm diameter
- Widely used in motors, stepper motors, encoders, and servo machines
XB NEMA 34 (86mm) Coupling 12.7×12.7mm
- Material: Aluminum alloy hubs and elastomeric polyurethane spider.
- Product Type: Clamp-style jaw coupling without keyway.
- Bore Diameter: 12.7*12.7mm
- Number of Screws: 2 each.
- Angular Misalignment: +/-1°.
- Parallel Misalignment: +0.20mm/-0.20mm .
- Maximum Rotational Speed: 6500RPM.
- Suitable for Nema 23 Stepper Motor or for any motor/rod having an 12.75mm diameter
- Widely used in motors, stepper motors, encoders, and servo machines.
XB NEMA 23 (57mm) Coupling 6.35x8mm
- Material: Aluminum alloy hubs and elastomeric polyurethane spider.
- Product Type: Clamp-style jaw coupling without keyway.
- Large Bore Diameter: 8mm
- Small Bore Diameter: 6.35mm
- Number of Screws: 2 each.
- Angular Misalignment: +/-1°.
- Parallel Misalignment: +0.20mm/-0.20mm .
- Maximum Rotational Speed: 6500RPM.
- Suitable for Nema 23 Stepper Motor or for any motor/rod having an 6.35mm diameter
- Widely used in motors, stepper motors, encoders, and servo machines.