A2212 BRUSHLESS DC MOTOR 1000KV
- Motor KV: 1000
- Operating voltage: 7.2V to 12V (2 to 3Li-poly or 6to10 NiCad)
- LiPO Batteries: 2S-3S
- No-load Current: 10 V: 0.5 A.
- Current Capacity: 12A/60S
- Maximum current:13Amp for 60Sec
- Maximum Watts:150 Watt
- Efficiency Current: 4-10A
- Shaft Diameter: 3.17 mm
- Prop Adapter is quality tested
- Minimum ESC Specification: 18A (30A Suggested)
- Maximum operating temperature: + 80°C
- Complete speed control because of a three-phase connection.
- Long-life as there are no moving contact
- Thrust @ 3S with 1045 propeller: 800gms approx
- Thrust @ 3S with 0945 propellers: 475gms approx
- Thrust @ 3S with 0845 propellers: 475gms approx
- Motor Dimensions: 27.5 x 30mm
- Weight of motor:50-60 grams
3.17mm RC Aluminum Bullet Propeller Adapter Holder
- Bore Diameter: 3.7mm (expandable up to 4.1mm).
- Material: Aluminium.
- Colour: Silver.
- Ease of interfacing.
- Rust-free and stain-free aluminum metal construction.
- Used to capture propeller with BLDC motor in quad-copter/multi-rotor/drone.
- High-quality aluminum material.
- Suitable for brushless motors and speed controllers.
- Delicate workmanship.
- High-Quality RC 3.17mm Prop Adaptor For Motor Propeller Plane, Multicopter, Quadcopter
- Dimension: 2.5mm Long x 12mm Diameter
- weight: 4g
Bullet Connector 3.5MM
- Diameter: 3.5mm
- Length:1.5CM & 1.5CM
- Amperage Rating: 60A -180Amps
- Hook up RC Battery to Electronic
- Hook up Brushless motor to electronic speed control
- These have low resistance and gives the best electric flow
- 5mm gold connectors Male
- 5mm gold connectors Female
- Dimension: 2.7*2.1*3inch
- Weight: 67gm
NEMA17 STEPPER L CLAMP
L298N MOTOR DRIVER
- Driver model: L298N 2A
- Driver chip: Double H bridge L298N
- Motor supply voltage: 46V(maximum)
- Motor supply current: 2A(maximum)
- Logic voltage: 5v
- Driver voltage: 5V-35V
- Driver current: 2A
- Logical current: 0-36mA
- Maximum power: 25W
- Current sensor for each motor
- LED indication for power status
- Heat sink for better performance
- Operating temperature: -25 degrees to 135 degrees Celsius
- Can be interfaced with simple manual switches, TTL logic gates, relays, etc.
- Dimension: 55*60*30mm
- Weight: 33gm
A3967 STEPPER MOTOR DRIVER
- A3967 precision micro-stepping driver
- Power supply: 7v to 30v
- Logic voltage: 5v to 3.3v
- Higher the voltage higher the torque at high speed
- Adjustable current control from 150Ma/ phase to 750ma phase
- Automatic current decay mode detection/selection
- Fast, slow, and mixed current decay modes
- Internal UVLO and thermal shutdown circuitry
- Crossover current protection
- Micro stepping resolution to full, half, quarter, and eighth steps by broken out MS1 and MS2 pins.
- Compatible with Arduino, GRBL G-Code interpreter for driving3-axis CNC machines
- Salington sink drivers used
- Compactible with 4, 6,8 wire stepper motor of any voltage
40A DC MOTOR SPEED REGULATOR PWM CONTROLLER 2000W
- Speed controller model: 40A PWM DC motor speed regulator
- Operating voltage: 10V TO 50V
- Peak current: 40A
- Control power: 0.01-2000W
- Quiescent current: 0.025A
- PWM regulation: 5-100%
- PWM frequency: 12KHz
- Operating temperature: -20 degree to 40 degree Celsius
- Stability in working
- High efficiency
- potentiometer used for speed adjustability
- Dimension: 9*5.1mm
- Weight: 95gm