NEMA 17 5.5 kgcm
- Step Angle : 1.8°
- Holding Torque : 5.5 KgCm
- Operating Voltage : 12 - 16 volts
- Supply Current (A) :1.5 Ampere
- Number of Leads : 6
- Inductance : 5.5 mH
- Resistance : 2.8 Ohms
- Weight (gm) : 363
- Detent Torque (kg-cm) : 2.6
- Frame Size (mm) : 42 x 42
- Inductance Accuracy : ±20%
- Resistance Accuracy : ±10%
- Step Angle Accuracy : ±5%
- Shaft Diameter (mm) : 5
- Shaft Length (mm) : 22
- Input pulse decides the rotation angle of the motor.
- High accuracy of around 3 to 5% a step.
- Provides good starting, stopping and reversing.
- Control of this motor is less costly because of exclusion of complex control circuitry.
- The speed is proportional to the frequency of the input pulses.
APM/Pixhawk Power Module V6.0 Output BEC 3A XT60 Plug 28V 90A
- Input Voltage Range: 6-28V DC
- Output voltage: 5.3V ± 0.1V
- Maximum output current: 3A
- Maximum current: 90A
- Maximum voltage: 30V
- Supports from 2 cell to 6 cell battery.
- 6P cable can be directly connected to APM/Pixhawk flight control
- Additional 4P rows of pin-free to wire/PIN to connect to another flight control
- Voltage and current measurement configured for 5V ADC.
- Switching regulator outputs 5.3V and 3A max.
- Dimensions: 25mm x 21mm x 9mm
- Weight: 17gm
BTS7960 43A High Power Motor Driver Module/Smart Car Driver Module for Arduino Current Limit
- Input voltage: 6V-27V
- Maximum current: 43A
- Input level: 3.3-5V
- Control mode: PWM or level
- Duty cycle: 0-100%
- Double BTS7960 large current (43 A) H bridge driver
- 5V isolate with MCU and effectively protect MCU
- 5V power indicator on board
- Four lines from MCU to driver module (GND. 5V. PWM1. PWM2)
- Reverse the motor forward, two PWM input frequency up to 25kHZ
- Two heat flow passing through an error signal output
- Dimension: Approx. 4 * 5 * 1.2cm
TB6560 Driver Board 3A CNC Router Single 1 Axis Controller Stepper Motor
- Supply voltage up to +32 VDC
- Output current up to 3.0A
- Pulse frequency up to 20 KHz
- Suitable for 2-phase and 4-phase motors
- Over-voltage and short-circuit protection
- 7 output current choices, max 3200 steps/rev
- Automatic idle-current reduction
- Single-chip motor driver for sinusoidal micro-step control of stepping motors
- High output withstands voltage due to the use of BiCD process:
- Forward and reverse rotation
- Selectable phase excitation modes (2, 1-2, 2W1-2, and 4W1-2)
- High output withstand voltage: VDSS = 40 V
- High output current: IOUT = TB6560AHQ: 3.5 A (peak)
- Internal pull-down resistors on inputs: 100 kΩ
- Output monitor pin: MO current (IMO (max) = 1 mA)
- Reset and enable pins
Solar Charge Controller 12v/24v 10A
Sunny Sky A2212 980 kv
- Poor man’s Tiger motor
- Brand name: Sunnysky
- KV: 980KV.
- Framework: 12N14P
- Operating Current: 6A ~ 18A
- Peak Current: 14A
- Shaft: 3mm.
- thrust: 880g
- Stator Diameter: 22mm
- Stator Thickness: 12mm
- of Stator Slots: 12
- of Rotor Poles: 14
- Motor Resistance: 123mΩ
- Max Continuous Power: 330W
- Recommended Lipo Batteries: 2-3S
- Recommended Propeller: 9-10
- Recommended Esc between 25A and 30A are
- High-quality bearings for reliable operation.
- Imported silicon steel coils, and high-quality magnets ensuring longer life and better performance.
- Generates less heat during operations.
- Suitable for RC Airplane or Multi rotor helicopter
- Dimension: 27*30mm
- Weight: 50gm
24V Dc 1/2″ Brass Electric Solenoid Valve Water Air Fuels Gas Normal Closed New
- Working Medium: Air, Water, Oil, Gas
- Voltage: DC24V, ±10%
- Operating Type: Directly driven
- State: Normally closed
- Flow bore: 16mm
- CV: 4.8
- Pipe Size: 1/2"
- Operating Viscosity: Under 20CST
- Operating Pressure: 0-10 Kg/cm²
- Working Temperature: -5 degrees to 80 degrees C
- Voltage: DC24V, ±10%
- Valve Body: Brass
- Electric lifting magnet
- Powerful and compact
- Smooth and flat surface
RS-50-555 Gear/Geared Motor 10 RPM – High Torque 12v DC
- Operating Voltage Range: 6V to 15V DC
- Recommended Voltage: 12V DC
- Rated RPM: 10 (at 12V)
- Rated Torque: 13 Kg-cm
- No- Load Current: 0.2 A
- Full Load Current: 4.8 A
- Full (Stall) Load Torque: 90Kg-cm
- Motor Dimensions: 38.2 x 65.8 mm
- Gearbox Dimensions: 51.2 x 34mm
- Motor Shaft Length: 21.18 mm
- Shaft Diameter: 7.15mm
- Motor Shaft Type: D
- Weight: 300 gm
RS-50 High Torque Side Shaft DC Gear Motor 200 RPM
- Operating Voltage Range: 6V to 15V DC
- Recommended Voltage: 12V DC
- Rated RPM: 10 (at 12V)
- Rated Torque: 4 Kg-cm
- No- Load Current: 0.2 A
- Full Load Current: 4.8 A
- Full (Stall) Load Torque: 90Kg-9kg
- Motor Dimensions: 38.2 x 65.8 mm
- Gearbox Dimensions: 51.2 x 34mm
- Motor Shaft Length: 21.18 mm
- Shaft Diameter: 7.15mm
- Motor Shaft Type: D
- Weight: 300 gm
DYS Motor D2826 1400KV
- Item name: D2826 1400KV
- Voltage: 4V~14.8V
- Battery: 2~4s LiPoly
- Max watt:205W
- Max Current: 19A
- Suggested prop: 9045
- Pull: 660g
- Shaft: 3.17mm in Diameter
- Thrust: 1050g (9045 prop/4s)
- Efficiency: <4g/W
- Suggested Propeller: 7x4(3S)Â ~Â 9x4.7 (2S)
- ESC: 40A
- Ri(M ): 0.078
- Pull: 780g
- Shaft: M5
- Motor Mount Holes: 16mm or 19mm
- Dimensions: 26.2 × 27.7mm
- Weight: 51g
DYS Motor D2826 1800KV
- Item name: D2826 1800KV
- Voltage: 4V~14.8V
- Battery: 2~4s LiPoly
- Max watt:300W
- Max Current: 19A
- Suggested prop: 9045
- Pull: 800g
- Shaft: 3.17mm in Diameter
- Thrust: 1050g (9045 prop/4s)
- Efficiency: <4g/W
- Suggested Propeller: 7x4(3S)Â ~Â 9x4.7 (2S)
- ESC: 40A
- Ri(M ): 0.078
- Pull: 780g
- Shaft: M5
- Motor Mount Holes: 16mm or 19mm
- Dimensions: 26.2 × 27.7mm
- Weight: 51g