Power HD 1501MG High-Torque Metal Gears Servo 60g/ 17kg-cm
- Motor Type: DC Motor
- Gear Type: Copper
- Stall Torque: 15.5 kg-cm (4.8V); 17.0 kg-cm (6V)
- Operating Speed: 0.16sec/60degree (4.8V); 0.14sec/60degree (6.0V)
- Temperature Range: -20℃ - +60℃
- Working Frequency：1520μs / 50Hz
- Servo Wire Length: 32cm
- Current Draw at idle: 10mA
- No Load Operating Current: 170mA
- Stall Current: 1.2A
- Dimension: 40.7mm X 20.5mm X 39.5mm
- Weight: 63g
JX PS-5521MG 20KG Large Torque Metal Gear Standrd Analog Servo
- Name: PS-5521MG Analog Servo
- Maximum Angle: 90°
- Gear: Metal
- Operating Voltage:4.8V-6V
- Dead band: 7µs 1520µs / 50hz
- Operating Speed (4.8V): 0.18 sec/60°
- Operating Speed (6V): 0.16 sec/60°
- Stall Torque (4.8V): 17.25 kg.cm (239.55oz/in)
- Stall Torque (6V): 20.32 kg-cm (281.89 oz/in)
- Connector Wire Length: JR 265 mm (10.43in)
- Bearing: 2BB
- Dimension: 40.5x40.3x20mm
- Weight: 85g
50Kg Pressure Micro Scale Weighing Sensor
- Capacity : 50.kg
- Output Sensitivity (mv/v): 1.0±0.1.
- Nonlinearity (%FS): 0.03.
- Repeatability (%FS): 0.03.
- Input Resistance: 1000. Ω
- Insulation Resistance : ≥5000.MΩ
- Alloy Steel wired weighing load cell
- High Accuracy
- Simple Structure & Easy Installation.
- Internal 1000 Ω half-bridge strain gauge load cell, the range is 50kg, half-bridge structure
- You can use multiple load sensors simultaneously to increase the capacity range, Parallel use to add additional capacity.
Aluminum Metal Servo Arm 25T Metal Horns Round Type Disc
TowerPro SG92R Mini Micro Servo 9g 2.5kg
- Operating Voltage: 4.8V to 6.0V
- Operating Temperature Range: -10 to +60 Degree C
- Operating Speed (4.8V): 0.12sec/60 degrees at no load
- Operating Speed (6.0V): 0.10sec/60 degrees at no load
- Stall Torque (4.8V): 1.8kg/cm
- Stall Torque (6.0V): 2.4kg/cm
- 360 Modifiable: Yes
- Bearing Type: Ball Bearing
- Gear Type: Nylon Gears
- Connector Wire Length: 12"
- Pulse Width: 500-2400 µs
- Rotation Angle: 180 degree
- Dimension: 21.5 x 11.8 x 22.7mm
- Weight: 9g
Servo Mount Bracket for SG90 MG90
VNH2SP30 – Monster Moto Shield 30A Mini Stepper Motor Driver
- Driver Model: Monster Moto Shield VNH2SP30
- Operating Voltage: 12V to 16V DC
- Maximum current rating: 30 A
- Continuous Current: 14 A
- Number of Channels: 1
- MOSFET on-resistance: 19 m (per leg)
- Maximum PWM frequency: 20 kHz
- Current sensing available to Arduino analog pin
- Thermal Shutdown
- Under voltage and Overvoltage shutdown.
- Dimensions: 55 x 28 x 12mm
- Weight: 15gm
ULN2003 Driver
- Contains 7 high-voltage and high current Darlington pairs
- Each pair is rated for 50V and 500mA
- Input pins can be triggered by +5V
- All seven Output pins can be connected to gather to drive loads up to (7×500mA) ~3.5A.
- Can be directly controlled by logic devices like Digital Gates PIC etc
- Available in 16-pin DIP, TSSOP, SOIC packages
- Dimensions: 32 x 18 x 11mm (LxWxH)
- Weight: 3 gm
TB6560 Driver Board 3A CNC Router Single 1 Axis Controller Stepper Motor
- Supply voltage up to +32 VDC
- Output current up to 3.0A
- Pulse frequency up to 20 KHz
- Suitable for 2-phase and 4-phase motors
- Over-voltage and short-circuit protection
- 7 output current choices, max 3200 steps/rev
- Automatic idle-current reduction
- Single-chip motor driver for sinusoidal micro-step control of stepping motors
- High output withstands voltage due to the use of BiCD process:
- Forward and reverse rotation
- Selectable phase excitation modes (2, 1-2, 2W1-2, and 4W1-2)
- High output withstand voltage: VDSS = 40 V
- High output current: IOUT = TB6560AHQ: 3.5 A (peak)
- Internal pull-down resistors on inputs: 100 kΩ
- Output monitor pin: MO current (IMO (max) = 1 mA)
- Reset and enable pins
MACH3 interface board
- Compatible Stepper Motor Driver - Max 5 2-phase Microstep controllers
- Driver type - Pulse and Direction signal control
- Wide input voltage range: 12-24V, and with anti-reverse function.
- Output 0-10V analogue voltage for the inverter to control the spindle speed.
- Compatible with MACH3, Linux CNC (EMC2) etc. parallel-control CNC software.
- USB power supply and peripherals power phase are separate to protect computer security.
- All the signals are to-isolate which can protect your computer security.
- 5-input interface to define the Limit, Emergence-Stop, Cutter alignment, etc.
- Wide input voltage range: 12-24V, and with anti-reverse function.
- One relay output control interface, accessed by the spindle motor or the air pump, water pump, etc.
- Maximum support 5-axis stepper motor driver controllers
- Output 0-10V analogue voltage for the inverter to control the spindle speed.
- All the way to the relay output port, control spindle switch. Output port P17 mouth.
- One relay output control interface, accessed by the spindle motor or the air pump, water pump, etc.
- Weight - Approx. 75g
- Dimensions - 90 * 70 * 20mm
Leadshine DMA860H
- Input voltage: Up to +80VAC or +110VDC.
- Output current Up to 7.2A.
- Pulse input frequency up to 300 KHz.
- Automatic idle-current reduction.
- Over-voltage, over-current protection.
- Suitable for 2-phase and 4-phase motors.
- Support PUL/DIR and CW/CCW modes.
- Operating Temperature : 70 C.
- High performance, cost-effective
- Self-adjustment technology
- Pure-sinusoidal current control technology
- TTL compatible and optically isolated input
- 16 selectable resolutions in decimal and binary, up to 51,200 steps/rev