CS DC Geared Motor 500 RPM
3S BMS BOARD 25A
- Charging Voltage: 12.6V DC CC/CV
- Balance Voltage for Single Cell: 4.2V
- Max Continuous Charge/Discharge Current: 25A
- Overcharge voltage range: 4.25-4.35v + 0.05v.
- Over discharge voltage range: 2.3-2.7v + 0.05v.
- Operating current: 0 – 25A.
- Operating temperature: -40 – +50℃.
- Instantaneous current: 35 – 40A.
- Storage condition: -40 – +80℃.
- Quiescent current: less than 30uA.
- Balance current: about 40 – 50mA.
- Effective life: more than 30000 hours.
- Internal resistance: less than 100m ohms.
- Short-circuit protection: protection, delayed self-recovery.
Square Geared Motor 60 RPM – High Torque
- Operating Voltage: 12 V DC
- No Load Current: ≤220 mA
- No load Speed: 60 RPM (at 12V)
- Full Load Current: ≤1300mA
- Rated Current: ≤4800 mA
- Rated Torque: 40 Kg-cm
- Shaft Length: 27 mm
- Shaft Diameter: 8 mm
- Length: 92mm
- Dimension Overall: 70 X 70 (Sq.) X 90 (Length)
- Heavy Duty Metal Gears.
- Uniformity of parts.
- Capability to absorb shock and vibration as a result of elastic compliance.
- Ability to operate with minimum or no lubrication, due to inherent lubricity.
- Relatively low coefficient of friction.
- Corrosion-resistance; elimination of plating, or protective coatings.
RS-50-555 Gear Motor – High Torque 12v DC 300 rpm
- Operating Voltage Range: 6V to 15V DC
- Recommended Voltage: 12V DC
- Rated RPM: 10 (at 12V)
- Rated Torque: 2 Kg-cm
- No- Load Current: 0.2 A
- Full Load Current: 4.8 A
- Full (Stall) Load Torque: 10Kg-cm
- Motor Dimensions: 38.2 x 65.8 mm
- Gearbox Dimensions: 51.2 x 34mm
- Motor Shaft Length: 21.18 mm
- Shaft Diameter: 7.15mm
- Motor Shaft Type: D
- Weight: 300 gm
RS-50 High Torque Side Shaft DC Gear Motor 200 RPM
- Operating Voltage Range: 6V to 15V DC
- Recommended Voltage: 12V DC
- Rated RPM: 10 (at 12V)
- Rated Torque: 4 Kg-cm
- No- Load Current: 0.2 A
- Full Load Current: 4.8 A
- Full (Stall) Load Torque: 90Kg-9kg
- Motor Dimensions: 38.2 x 65.8 mm
- Gearbox Dimensions: 51.2 x 34mm
- Motor Shaft Length: 21.18 mm
- Shaft Diameter: 7.15mm
- Motor Shaft Type: D
- Weight: 300 gm
JOHNSON MOTOR HIGH TORQUE DC GEARED 12V 600RPM – GRADE A
- 600RPM 12V DC motors with Metal Gearbox and Metal Gears
- 18000 RPM base motor
- Holding Torque: 4.53kgcm
- 6mm Dia shaft with M3 thread hole
- Gearbox diameter 37 mm.
- Motor Diameter 28.5 mm
- Length 63 mm without shaft
- Shaft length 30mm
- 180gm weight
- No-load current = 800 mA, Load current = upto 7.5 A(Max)
- Recommended to be used with DC Motor Driver 20A or Dual DC Motor Driver 20A
- Grade A Quality branded Johnson DC Motor.
- It has a sturdy construction.
- Comes with Rear shaft for encoder mounting
- Shaft equips metal bushes for long life.
- It comes with High-Quality gears.
- The shaft has a hole for better coupling.
12V DC Johnson Motor Grade A-100 RPM
- 100RPM 12V DC motors with Metal Gearbox and Metal Gears
- 18000 RPM base motor
- Holding Torque: 27.18kgcm
- 6mm Dia shaft with M3 thread hole
- Gearbox diameter 37 mm.
- Motor Diameter 28.5 mm
- Length 63 mm without shaft
- Shaft length 30mm
- 180gm weight
- No-load current = 800 mA, Load current = upto 7.5 A(Max)
- The motor has sturdy construction.
- Shaft equips metal bushes for long life.
- It comes with High-Quality gears.
- The shaft has a hole for better coupling.
28BYJ-48 5V Stepper motor
- High-quality stepper motor
- Voltage: DC 5V
- Diameter: 25mm
- Step Angle: 5.625 x 1/64
- Reduction Ratio: 1/64
- Rated voltage ： 5VDC
- Number of Phase ： 4
- Speed Variation Ratio ： 1/64
- Stride Angle ： 5.625° /64
- Frequency : 100Hz
- DC resistance ： 50Ω±7%(25℃)
- Idle In-traction Frequency : > 600Hz
- Idle Out-traction Frequency : > 1000Hz
- In-traction Torque >34.3mN.m(120Hz)
- Self-positioning Torque >34.3mN.m
- Friction torque : 600-1200 gf.cm
- Pull in torque : 300 gf.cm
- Insulated resistance >10MΩ(500V)
- Insulated electricity power ：600VAC/1mA/1s
- Insulation grade ：A
- Rise in Temperature <40K(120Hz
- Noise <35dB(120Hz,No load,10cm)
DC 12V KK-P25/20 5KG Lifting Solenoid Electromagnet
- Operating Voltage: 12V DC.
- Lifting Capacity: 5KG.
- Electric lifting magnet.
- Powerful and compact.
- Smooth and flat surface.
- Low consumption and reliability.
- The ambient temperature within 130 degrees.
- High mechanical strength and excellent durability
- Minimized residual magnetic force
- Lightweight, compact design for space-saving.
- Dimension: 25 x 20 mm.
DC 12V Pneumatic Diaphragm Water Pump Motor R365
- Model: R365 DC micro diaphragm pump
- Working voltage: DC 12V
- No load current: 0.23A
- Maximum flow: 2-3 liters/minute
- Outlet maximum pressure: 1-2.5 kg
- Maximum lift: 1-2.5 meters
- Maximum suction: 2 meters
- Motor length: 32mm
- Motor diameter: 28mm
- Pump length: 36mm
- Total length: 69mm
- Pump diameter: 40mm x 35mm
- Weight: 111 g Approx
APM/Pixhawk Power Module V6.0 Output BEC 3A XT60 Plug 28V 90A
- Input Voltage Range: 6-28V DC
- Output voltage: 5.3V ± 0.1V
- Maximum output current: 3A
- Maximum current: 90A
- Maximum voltage: 30V
- Supports from 2 cell to 6 cell battery.
- 6P cable can be directly connected to APM/Pixhawk flight control
- Additional 4P rows of pin-free to wire/PIN to connect to another flight control
- Voltage and current measurement configured for 5V ADC.
- Switching regulator outputs 5.3V and 3A max.
- Dimensions: 25mm x 21mm x 9mm
- Weight: 17gm
