XB NEMA 23 (57mm) Coupling 8×9.5mm
- Material: Aluminum alloy hubs and elastomeric polyurethane spider.
- Product Type: Clamp-style jaw coupling without keyway.
- Large Bore Diameter: 9.5mm
- Small Bore Diameter: 8mm
- Number of Screws: 2 each.
- Angular Misalignment: +/-1°.
- Parallel Misalignment: +0.20mm/-0.20mm .
- Maximum Rotational Speed: 6500RPM.
- Suitable for Nema 23 Stepper Motor or for any motor/rod
- Widely used in motors, stepper motors, encoders, and servo machines.
L293D Motor Driver Board for ESP8266 WiFi NodeMcu Lua ESP12E
- Motor power supply Range: 4.5V ~ 36V
- Control power Range: 4.5V ~ 9V (10VMAX)
- Logic Operating current: ≤60mA
- Drive part of the work current Io: ≤1.2A
- Maximum power dissipation: 4W
- Drive Type: Dual high-power H-bridge driver
- Working temperature: -25 ℃ ~ + 125 ℃
- ESP12 DEV KIT development board expansion module
- Lead ESP12 DEV KIT all the features of pins: SPI, UART, GPIO, AI, and 3.3V power connector
- Extend two-way motor-driven, two-way direct-drive motor
- on board power switch
- Motor power, control power separation
- Dimension: 60 x 45 x 13mm
AP Extension pigtail SMA female socket jack to UFL IPX Connector
PIC16F876A Microcontroller IC
- Maximum CPU Frequency: 20 MHz
- Architecture: 8 bit
- Program Memory (Flash): 14 kB
- RAM: 368 byte
- Internal Oscillator: No
- ADC: 1 (5 channels)
- of Pins: 28
- Voltage: 2V - 5.5V
- 100,000 erase/write cycle Enhanced Flash program memory typical
- 1,000,000 erase/write cycle Data EEPROM memory typical
- Data EEPROM Retention > 40 years
- Self-reprogrammable under software control
- In-Circuit Serial Programming™ (ICSP™) via two pins
- Single-supply 5V In-Circuit Serial Programming
- Watchdog Timer (WDT) with its own on-chip RC oscillator for reliable operation
- Programmable code protection
- Power saving Sleep mode
- Selectable oscillator options
- In-Circuit Debug (ICD) via two pins
- CMOS TECHNOLOGY:
- Low-power, high-speed Flash/EEPROM technology
- Fully static design
- Wide operating voltage range (2.0V to 5.5V)
- Commercial and Industrial temperature ranges
- Low-power consumption
PIC18F458 Microcontroller IC
- Maximum CPU Frequency: 40 MHz
- Architecture: 8 bit
- Program Memory (Flash): 32 kB
- RAM: 1536 byte
- Internal Oscillator: No
- ADC: 1 (8 channels)
- of Pins: 40
- Voltage: 2V - 5.5V
- Power-on Reset (POR), Power-up Timer (PWRT) and Oscillator Start-up Timer (OST)
- Watchdog Timer (WDT) with its own on-chip RC oscillator
- Programmable code protection
- Power-saving Sleep mode
- Selectable oscillator options, including:
- In-Circuit Serial ProgrammingTM (ICSPTM) via two pins
- Low-power, high-speed Enhanced Flash technology
- Fully static design
- Wide operating voltage range (2.0V to 5.5V)
- Industrial and Extended temperature ranges
250V Float Switch Sensor for Water Level Controller-Big
- Protection: Waterproof
- Medium Working Pressure: Max 1 Bar
- Circuit Breaking Capacity: Directly KW with 250V
- Medium Temperature: 70 Deg.C.
- Mechanical endurance: ≥100,000 times
- Electrical endurance: ≥500,000 times
- Cable length: 3m
- Corrosion Free,
- Sturdy and durable & need no maintenance.
- No current / voltage is passed through water, therefore no electrolysis or Salt deposition.
- Long life (approximate 10 million operations)
- Rust proof (entire sensor body in polypropylene)
- Used in hard water or fuel such as diesel, kerosene, oil etc.
- Dimensions : 11 x 9 x 5cms
- Weight 690 grams
XB NEMA 23 (57mm) Coupling 8x8mm
- Material: Aluminum alloy hubs and elastomeric polyurethane spider.
- Product Type: Clamp-style jaw coupling without keyway.
- Dimensions: bore size: 8mm x 8mm.
- Number of Screws: 2 each.
- Angular Misalignment: +/-1°.
- Parallel Misalignment: +0.20mm/-0.20mm .
- Maximum Rotational Speed: 6500RPM.
- Suitable for Nema 23 Stepper Motor or for any motor/rod having an 8mm diameter
- Widely used in motors, stepper motors, encoders, and servo machines.
6V 300mA Solar Panel
- Max output power: 3.23W
- Max working voltage: 6.6V
- Max charging current: 490mA
- Min output power: 2.7W
- Min working voltage: 6V
- Min charging current: 450mA
- Small Epoxy Solar Panels are simple to install or add to your existing product
- Construction requires no frame or special modifications
- Small space required for installation.
- Has 2 to 3 times the power of amorphous thin-film solar panels
- Ready to use, they require no frame or special modifications.
- For connection, just solder or crimp to the copper tape.
- Laser cut to proper size and encapsulated in special sun and weather resistant materials;
- Dimensions: 13.2 Cm X 15 Cm Thickness 3mm +/- 2 mm
- Weight 136gm
Solar Panel 9V 200mA
- Quality custom-design solar energy panel
- The solar cells are encased and protected by a durable outer poly frame
- Polycrystalline solar cells
- Max output power: 1.8W
- Max power voltage: 9V
- Max power current: 200mA
- Open circuit voltage: 10.8v
- Short circuit current: 220mA
- Small Epoxy Solar Panels are simple to install or add to your existing product.
- Construction requires no frame or special modifications
- Small space required for installation.
- Has 2 to 3 times the power of amorphous thin-film solar panels
- Ready to use, they require no frame or special modifications.
- For connection, just solder or crimp to the copper tape.
- Dimension: 11.5cm x 13.6cm x 3mm
- Weight 49gms
20/4 GREEN (LCD DISPLAY MODULE)
- Operating voltage: 5V
- Display format: 20 characters * 4 line
- Display mode: STN or FSTN
- Dot-matrix: 5*8 dots
- Character size: 2.95 * 4.75mm
- Character pitch: 3.55 * 5.35mm
- LCD driver IC: ST7066U
- 1/16 duty cycle
- Wide viewing angle and high contrast
- Works on both 8-bit parallel interface
- Operating temperature: -20 degree to 70 degree Celsius
- Low Current consumption
- Dimension: 98*60*13.6mm
- Compact size and lightweight
7 PIN 0.96” 128*64 WHITE OLED
- High resolution: 128*64
- Input voltage: 3V to 5 V DC
- Ultra-wide viewing angle >160 degree
- Ultra-low power consumption
- Fully compatible with Arduino, 51 series, MSP430, STM32/2, CSR IC.
- Driver IC: SSD1306
- Display colour: white
- Performs without the need for a backlight
- Interface: IIC/SPI, needs 4 I/O only
- Compatible I/O level: 3.3v, 5v
- Working temperature: -40 degrees to 70 degrees Celsius
- Dimension: 27.3*27.8*3.7mm
- Support a wide range of input
- Size: 99gm