30AMPS ESC DYS
- Input Voltage: 11.1 ~ 11.7 V.
- Constant Current: 30A (Max 40A<10s).
- BEC: 5V/3A.
- Li-Po battery: 2S ~ 3S.
- Ni-MH 4-10 CELLS Auto Detect.
- Separately voltage regulator IC for the microprocessor, providing good anti-jamming capability.
- Used with SimonK updated firmware for Multicopter
- Battery side – Male deans (T) connector.
- Motor side – Female 3.5mm gold connector.
- 30A ESC for BLDC has onboard BEC.
- Developed specifically for multi-rotor use
- Smooth, linear, and precise throttle response
- Extreme low output resistance, super current endurance
- Auto Low Battery Slow down at 3.0V/cell Lipo, cut-off at 2.9V/cell lipo.
- Supported motor speed (Maximum): 210000 RPM (2 poles), 70000 RPM (6 poles), 35000 RPM (12 poles).
- Dimension: 46* 26 * 11mm
- Weight: 23g
Ardupilot Mega APM 2.8 Flight Controller
- Model: APM 2.8
- Input Voltage (V): 12-16 V.
- Processor: ATMEGA2560 and ATMEGA32U-2
- Micro SD card slot: No.
- Arduino Compatible
- MPU6000 : 3-Axis MEMS Gyroscope + accelerometer
- High-performance Barometer upgraded to MS5611-01BA03, from Measurement Specialties.
- Support hundreds of 3D waypoints
- Full mission scripting with point-and-click desktop utilities
- Two-way telemetry and in-flight command using the powerful MAVLink protocol
- Powerful Ground Control Software
- Supports full "hardware-in-the-loop" simulation with Xplane and Flight Gear
- On-board 4 Megabyte Data flash chip for automatic data logging.
- Optional off-board GPS, an uBlox LEA-6H module with Compass.
- Dimensions: 70 x 45 x 15mm
- Weight: 70gm
AfroFlight Naze32 Rev6 Flight Controller Board
- Version: 6 DOF
- Input voltage: Max 16V on input rail and up to 35V 6s on the voltage sense line
- USB on right side
- 32-bit processor running at 3.3V/72MHz (STM32F103CB).
- Up to 8 Ch. RC input - supports standard receivers (PWM), PPM Sum receiver (FrSky, etc), or Spectrum satellite receivers
- Built-in FrSky telemetry inverter
- Battery voltage monitoring
- SBUS Inverter built-in
- Spectrum satellite
- Modern GUI for all operating systems, Baseflight Configurator.
- Supports multiple platforms: Quad/Hexa/Tri/Bi/Y4/Y6/Octo/Camera Gimbal. (Default is Quad-X)
- MPU6500 : 3-Axis MEMS Gyroscope + accelerometer
- Onboard MicroUSB for setup and configuration
- BMP280 barometer
- Modern GUI for all operating systems, Baseflight Configurator.
- Sonar pads w/resistors added for direct connection to 5V sonar3.3V
- Dimensions: 36x36 mm (30.5mm Mounting)
- Weight: 5.3 grams (no headers, 7.3 grams with).
Simonk ESC 30A
- Standard 30A BLDC ESC Electronic speed controller
- Input voltage: DC 6V-16.8V(2-4S Lixx)
- BEC: 5V 2amp
- Easy handling and good compatibility
- Suitable Batteries: 2-3S LiPo.
- Application: BLDC Motors, Multirotor, RC Planes et
- Running current: 30A (Output: Continuous 30A, Burst 40A up to 10 Secs.)
- Size: 36* 26* 7mm
- Weight: 32g
Smart Robot Car Chassis Kit 2 Wheels
- This car is the tachometer encoder.
- Works with a 4 AA battery box (batteries not included).
- Used for distance measurement, velocity.
- Can use with other devices to realize the function of tracing, obstacle avoidance, distance testing, speed testing,
- Wireless remote control.
- Laser Cut Acrylic Chassis
- Two Dual Shaft Motors For Either Side
- Universal Castor To Avoid Slippage
- Placeholders For Different Sensors, Servos, and Modules
- Has Strong Torsion, With 130 Strong Magnetic Dc Motor. Speed Ratio 1: 48
- Size: 21 x 15 cm (L x W).
- Wheel size: 6.5 x 2.7cm (Diameter x Height).
