Showing all 8 results

AfroFlight Naze32 Rev6 Flight Controller Board

  • Version: 6 DOF
  • Input voltage: Max 16V on input rail and up to 35V 6s on the voltage sense line
  • USB on right side
  • 32-bit processor running at 3.3V/72MHz (STM32F103CB).
  • Up to 8 Ch. RC input - supports standard receivers (PWM), PPM Sum receiver (FrSky, etc), or Spectrum satellite receivers
  • Built-in FrSky telemetry inverter
  • Battery voltage monitoring
  • SBUS Inverter built-in
  • Spectrum satellite
  • Modern GUI for all operating systems, Baseflight Configurator.
  • Supports multiple platforms: Quad/Hexa/Tri/Bi/Y4/Y6/Octo/Camera Gimbal. (Default is Quad-X)
  • MPU6500 : 3-Axis MEMS Gyroscope + accelerometer
  • Onboard MicroUSB for setup and configuration
  • BMP280 barometer
  • Modern GUI for all operating systems, Baseflight Configurator.
  • Sonar pads w/resistors added for direct connection to 5V sonar3.3V
  • Dimensions: 36x36 mm (30.5mm Mounting)
  • Weight: 5.3 grams (no headers, 7.3 grams with).
 

Anti-Vibration Shock Absorber for APM/KK/MWC/PixHawk

  • Colour: Black
  • Material: Glass Fibre
  • Upper Frame size:90x60x2mm
  • Lower Frame Size: 100x70x2mm
  • Shock absorber Height: 10×12mm
  • Light Weight.
  • Vibration Resistant with included Shock absorbers.
  • Shock Absorber material: Synthetic Rubber.
  • Universal Fiber Mount Shock Absorber Plate for flight controllers
  • Compact design
  • Super lightweight
  • Mounting holes on the bottom makes it easy to install
  • Suit for different open-source flight controller, like APM 2.5/2.6/2.8, KK, MWC, and Pixhawk 2.4
  • Weight: 2gm

APM/Pixhawk Power Module V6.0 Output BEC 3A XT60 Plug 28V 90A

  • Input Voltage Range: 6-28V DC
  • Output voltage: 5.3V ± 0.1V
  • Maximum output current: 3A
  • Maximum current: 90A
  • Maximum voltage: 30V
  • Supports from 2 cell to 6 cell battery.
  • 6P cable can be directly connected to APM/Pixhawk flight control
  • Additional 4P rows of pin-free to wire/PIN to connect to another flight control
  • Voltage and current measurement configured for 5V ADC.
  • Switching regulator outputs 5.3V and 3A max.
  • Dimensions: 25mm x 21mm x 9mm
  • Weight: 17gm

Ardupilot Mega APM 2.8 Flight Controller

2,999.00
  • Model: APM 2.8
  • Input Voltage (V): 12-16 V.
  • Processor: ATMEGA2560 and ATMEGA32U-2
  • Micro SD card slot: No.
  • Arduino Compatible
  • MPU6000 : 3-Axis MEMS Gyroscope + accelerometer
  • High-performance Barometer upgraded to MS5611-01BA03, from Measurement Specialties.
  • Support hundreds of 3D waypoints
  • Full mission scripting with point-and-click desktop utilities
  • Two-way telemetry and in-flight command using the powerful MAVLink protocol
  • Powerful Ground Control Software
  • Supports full "hardware-in-the-loop" simulation with Xplane and Flight Gear
  • On-board 4 Megabyte Data flash chip for automatic data logging.
  • Optional off-board GPS, an uBlox LEA-6H module with Compass.
  • Dimensions: 70 x 45 x 15mm
  • Weight: 70gm
 

CC3D flight Control

  • Powerful STM32 32-bit microcontroller running at 90 MIPS with 128KB Flash and 20KB RAM.
  • 3-axis high-performance MEMs gyros and 3-axis high-performance MEMs accelerometer.
  • Tiny 36 x 36 mm 4 layer PCB for superior electrical noise reduction and flight performance.
  • Software support for Windows, Mac, and Linux.
  • Supported by powerful OpenPilot GCS
  • 10 PWM outputs to servos or ESC’s, or for camera stabilization
  • Direct high-speed USB support with no drivers required, a true plug and play device.
  • Spectrum satellite receiver support.
  • Futaba S-BUS hardware support.
  • With a function of being directly plugged into the satellite receiver
  • 10 PWM outputs to servos or ESC’s, or for camera stabilization
  • Innovative Flexi-port technology for superior port flexibility.
  • 4Mbits on-board EEPROM for configuration storage.

KK-Mini FLIGHT CONTROLLER

  • IC: Atmega644 PA
  • Gyro/Accelerometer: Auto-level: Yes
  • Input Voltage: 4.8-6.0V
  • AVR interface: standard 6 pins.
  • Signal from Receiver: 1520us (5 channels)
  • Signal to ESC: 1520us
  • LCD size: 24*18mm
  • Mini buttons size: Four 3.3*4.2mm
  • Mounting holes: 30.5x30.5mm
  • Voltage sensor: One red positive pin header for.
  • Input rail: Single row 2.54mm pitch pin header for input signal
  • Firmware Version: 1.6
  • Dimension: 36x36x11.5mm

KK2.1.5 Flight Control

1,999.00
  • IC: Atmega644 PA
  • Input Voltage: 4.8V-6.0V.
  • AVR Interface: Standard 6 Pin.
  • Signal from Receiver: 1520us (5 channels)
  • Signal to ESC: 1520us.
  • Gyro/Accelerometer: MPU 6050
  • Auto Level function
  • Firmware Version: 1.6
  • Dimension: 50.5mm x 50.5mm x 12mm

Mini OSD W/ KV Team MOD For Racing F3 Naze32 Flight Controller RC Drone

  • NO DC/DC converter, hence less heating
  • FTDI cable compatible pinout
  • Standard 6-pin ISP header
  • Two LED indicators
  • ATmega328P with Arduino bootloader
  • MAX7456 monochrome on-screen display
  • Pad for an Analog or Digital PWM RSSI signal
  • Pad for the connection of a Current Sensor
  • ATmega328P with Arduino bootloader
  • Standalone, or with APM / Flip / Flip32+ flight controllers
  • These modifications allow direct connection of two batteries (up to 4S)
  • This hardware take the hardware mods for this firmware, and builds them into an RTF solution.
  • This Board can be used just as a normal OSD for APM or it can be used with MWC KV Team Mod.
  • Two independent power sections with an LED indicator on each.
  • Solder jumpers for combining the power sections
  • Solder jumper for PAL video option
  • +5V 500mA regulator for up to +12V supply input
  • Exposed test points for HSYNC and LOS ATmega328P with Arduino bootloader.
  • Dimension: 16 x 16mm