IoT
LoRa SX1278 433M 10KM Wireless Spread Spectrum Transmission Module Ra-02 SX1278 Socket IOT
- Lora Spread Spectrum Modulation Technology +20dBm-100mW
- Constant RF power output when voltage changes
- High sensitivity: low to -148dBm
- Half-duplex SPI communication Programmable bit rates up to 300kbps
- Supports FSK, GFSK, MSK, GMSK, LoRa and OOK modulation modes
- 127dB RSSI dynamic range
- Automatic RF signal detection
- CAD model and ultra-high-speed AFC With CRC, up to 256 bytes of the packet engine
- Small volume dual-row stamp-hole patch package
- With shielding shell Spring antenna (Ra-01) external antenna (Ra-02)
- Wireless standard 433MHz Frequency range: 420 ~ 450MHz
- Interface: SPI GPIO
- Operating Voltage:1.8 ~ 3.7V, the typical value is 3.3V
- Current: Receiver:≦ 10.8mA (LnaBoost off, band 1) Transimit: ≦ 120mA (+ 20dBm)
- Sleep mode: 0.2μA
- Working temperature: -40 to + 85 ° C
- Storage temperature: Normal
XBee Module S2C XB24CZ7WIT-004
- Protocol: ZigBee®
- Transceiver chipset: Silicon Labs EM357 SoC
- RF Standard: 802.15.4
- Frequency (ISM Band): 2.4GHz
- Digital I/O: 15
- ADC Channels: (4) 10-bit ADC inputs
- Data Rate: RF 250 Kbps, Serial up to 1 Mbps
- Range: Indoor 200 ft (60 m), Outdoor (LOS) 4000 ft (1200 m)
- Transmit Power: 3.1 mW (+5 dBm)
- Channels: 16 channels
- Encryption: 128-bit AES
- Voltage requirements: 2.1 to 3.6 VDC
- Current requirements: ~33 mA @ 3.3VDC (transmit), ~28 mA @ 3.3VDC (receive), <1 uA @25ºC (sleep)
- Migratable to Digi Mesh and ZigBee PRO protocols
- Configuration Method: API or AT commands, local or over-the-air (OTA)
- Communication: CMOS UART / SPI
- Dimensions: 27.61 x 24.38 x 4.06 mm
- Operating temperature range: -40 to +85 °C
- Integrated, Wire Antenna
- Interoperable with other ZigBee-compliant devices
- Programmable versions with on-board microprocessor enable custom ZigBee application development
- Supports binding and multicasting for easy integration into a home automation platform
- Through-hole form factor enables flexible design
LOLIN32 V1.0.0 ESP32 Rev1 Wifi Bluetooth Board
L293D Motor Driver Board for ESP8266 WiFi NodeMcu Lua ESP12E
- Motor power supply Range: 4.5V ~ 36V
- Control power Range: 4.5V ~ 9V (10VMAX)
- Logic Operating current: ≤60mA
- Drive part of the work current Io: ≤1.2A
- Maximum power dissipation: 4W
- Drive Type: Dual high-power H-bridge driver
- Working temperature: -25 ℃ ~ + 125 ℃
- ESP12 DEV KIT development board expansion module
- Lead ESP12 DEV KIT all the features of pins: SPI, UART, GPIO, AI, and 3.3V power connector
- Extend two-way motor-driven, two-way direct-drive motor
- on board power switch
- Motor power, control power separation
- Dimension: 60 x 45 x 13mm
Ethernet Shield
- Based on the W5100Based on the Wiznet W5100 allows an Arduino board to connect to the internet.
- Stackable Design, can directly be supported by Arduino official Ethernet Library.
- Supports up to four simultaneous socket connections
- Can be used to store files for serving over the network.
- Compatible with the Arduino Duemilanove (168 or 328), Uno as well as Mega (1280/2560).
- Can be accessed using the Mini SD TF library.
- The current shield has a Power over Ethernet (PoE) module designed to extract power from a conventional twisted-pair Category 5 Ethernet cable.
- IEEE802.3af compliant
- Low output ripple and noise (100mVpp)
- Overload and short-circuit protection
- 1500V isolation (input to output)
Wemos D1 WiFi Esp8266 Development Board Uno Compatible Program
- Microcontroller: ESP-8266EX
- Operating Voltage: 3.3 V
- Digital I/O Pins: 11
- Analog Input Pins 1(Max input: 3.2V)
- Clock Speed: 80MHz/160MHz
- Flash: 4M bytes
- Good stability.
- 11 digital input/output pins, all pins have interrupt/PWM/I2C/one-wire supported(except for D0)
- 1 analog input(3.2V max input)
- Micro USB connection
- Compatible with Arduino
- Support OTA wireless uploading
- On-Board Switching Power Supply:
- Micro USB connection
- Compatible with Arduino
- Support OTA wireless uploading
GSM/GPRS/GPS SIM 808 IOT Modem
- Input voltage: 5V-12V DC Operation
- Working temperature:-40°C ~85°C
- Supply voltage range 3.4 ~ 4.4V
- Low power consumption
- Operation temperature:-40°C ~85°C
- Power supply: 3.4V ~ 4.4V
- Charging: Supports charging control for Li-Ion battery
- Quad-band 850/900/1800/1900MHz
- GPRS multi-slot class 12/10
- GPRS mobile station class B
- Compliant to GSM phase 2/2+ – Class 4 (2 W @ 850/900MHz) – Class 1 (1 W @ 1800/1900MHz)
- Dimensions: 24*24*2.6mm
- Control via AT commands (3GPP TS 27.007, 27.005 and SIMCOM enhanced AT Commands)
- Modem with Impedance Matching Layout.
- Fully Automatic Pick and Place Machine.
- On-board SMA connector for GSM antenna
- On-board UFL connector for External GSM Antenna
- On-board SMA & UFL connector for GPS Antenna
- Option to Connect Patch antenna or Active Antenna for GPS
- Onboard 3V3 Voltage regulator for GPS External Active Antenna
- Onboard Micro USB Connector for module firmware updation
- Automatic and Manual Start option (SMD Switch has provided for Manual Startup)
- LM39302 linear voltage regulator is used for provides a low-dropout, high-current output
- Onboard RMC connector for power supply
- Onboard RMC connector for audio interface
- On-board Connector for connecting 3.7V Li-Po battery
- Zener diode is used to prevent Accidental over voltage
- On board TXB0104 voltage level translator IC which helps us to interface with 2.8V to 5V microcontrollers’
- On board LED for power indication, Network and status.
- Header option for interfacing ADC, I2c,PWM
- Four 3MM Mounting Holes are Provided
- Flap Type SIM Card Connector
- On-board Anti-Static Protection IC
- Easy to Make and receive voice calls, Send and receive SMS messages
Xbee Module S2C XBP24CZ7UIT-004
- Protocol: ZigBee
- Modulation: DSSS
- Frequency: 2.4GHz
- Data Rate: 1Mbps
- Power: Output 18dBm
- Sensitivity: 101dBm
- Serial Interfaces: SPI, UART
- Antenna Type: Antenna Not Included, U.FL
- Transceiver chipset: Silicon Labs EM357 SoC
- Operating voltage: 2.7V-3.6V
- Current Receiving: 31mA ~ 45mA
- Current Transmitting: 120mA
- Mounting Type Through Hole
- Operating Temperature: -40°C ~ 85°C
Xbee Pro S2C Module XBP24CZ7WIT-004
- Operating voltage: 2.7V-3.6V
- Max data rate: 250kbps
- 63mW output (+17dBm)
- Range: 1 mile (1600m)
- ADC Channels: 6 10-bit ADC input pins
- Digital I/O: 8
- 128-bit encryption
- Transmit Current: 120mA at 3.3VDC
- Receive current: 31mA at 3.3VDC
- Data Rate: RF 250Kbps, serial up to 1Mbps
- Indoor/urban range up to 300ft (90m)
- outdoor/RF line of sight range up to 2miles (3200m)
- Transmit power is 63mW (+18dBm)
- Receiver sensitivity is -101dBm
- Local or over-air configuration
- AT or API command set
- External Antenna Required
- Firmware upgrades via UART, SPI or over the air (OTA)
- ISM 2.4GHz frequency band, DSSS (direct sequence spread spectrum) interference immunity
- Dimension: 2.438cm x 3.294cm
ESP8266-12E 10A 220V NETWORK RELAY WIFI MODULE INPUT DC 7V-30V
- Input voltage: DC 7V-30V
- Relay voltage: 220V
- Relay current: 10A
- ISM: 2.4GHz
- PA: +25dBm
- Input over-voltage protection
- Input overcurrent protection
- ESP8266 WIFI module with 4 layered board design
- LED indicator for input status and output status
- 220V 10A relay, normally opened, and one normally closed
- Optocoupler isolation input, TVS input protection
- Access server control via HTTP protocol by TCP client mode, high current terminals
- Dimension: 65*40*18mm