8051 Microcontroller IC
- Boolean Processor
- Bit-Addressable RAM
- Program Memory: 4Kx8 ROM
- RAM: 128 x 8 RAM
- No of Timers: 2 x 16-bit
- Interrupts: 5
- Package: PDIP
- Compatible with MCS-51® Products
- 4K Bytes of In-System Programmable (ISP) Flash Memory – Endurance: 1000 Write/Erase Cycles
- 0V to 5.5V Operating Range
- Fully Static Operation: 0 Hz to 33 MHz
- Three-level Program Memory Lock
- 32 Programmable I/O Lines
- Full Duplex UART Serial Channel
- Low-power Idle and Power-down Modes
- Interrupt Recovery from Power-down Mode
- Watchdog Timer
- Dual Data Pointer
- Power-off Flag
- Fast Programming Time
- Flexible ISP Programming (Byte and Page Mode)
80C31 Microcontroller IC
- 8051 Central Processing Unit
- Memory addressing capability
- Power control modes:
- CMOS and TTL compatible
- Three speed ranges at VCC = 5V
- Three package styles
- Extended temperature ranges
- Dual Data Pointers
- Second DPTR register
- Security bits:
- Encryption array—64 bytes
- 4 level priority interrupt
- 6 interrupt sources
- Four 8-bit I/O ports
- Full–duplex enhanced UART
- Programmable clock out
- Asynchronous port reset
- Low EMI (inhibit ALE)
- Wake-up from Power Down by an external interrupt (8XC51)
Arduino LilyPad 328 ATmega328P Main Board 16M Compatible with Arduino
- Microcontroller: ATmega168 or ATmega328V
- Operating Voltage: 2.7-5.5 V
- Digital I/O Pins: 14
- PWM Channels: 6
- Analog Input Channels: 6
- DC Current per I/O Pin: 40 mA
- Board will run from 2V to 5V.
- The latest version of the LilyPad supports automatic reset for even easier programming.
- The back side of the LilyPad is now completely flat!
ATtiny85 Arduino-enabled Mini USB Dev Board
- Support for the Arduino IDE 1.0+ (OSX/Win/Linux)
- Power via USB or External Source
- Onboard 5V Regulator
- Built-in USB
- 6 I/O Pins
- 8k Flash Memory (about 6k after bootloader)
- I2C and SPI (vis USI)
- PWM on 3 pins (more possible with Software PWM)
- 10-bit ADC
- ADC on 4 pins
- Power LED and Test/Status LED
- Low Power Consumption
- Active Mode:1 MHz, 1.8V: 300 µA
PIC12F508 Microcontroller IC
- Maximum CPU Frequency: 4 MHz
- Architecture: 8 bit
- Program Memory (Flash): 0.75kb
- RAM: 25 byte
- Internal Oscillator: 4 MHz
- of Pins: 8
- Voltage: 2V - 5.5V
- 4 MHz Precision Internal Oscillator: - Factory calibrated to ±1%
- In-Circuit Serial Programming™ (ICSP™) •
- In-Circuit Debugging (ICD) Support
- Power-On Reset (POR)
- Device Reset Timer (DRT) •
- Watchdog Timer (WDT) with Dedicated On-Chip RC Oscillator for Reliable Operation
- Programmable Code Protection
- Multiplexed MCLR Input Pin
- Internal Weak Pull-Ups on I/O Pins
- Power-Saving Sleep mode
- Wake-Wp from Sleep on Pin Change
- Selectable Oscillator Options:
- Operating Current: - < 175 μA @ 2V, 4 MHz, typical
- Standby Current: - 100 nA @ 2V, typical
- Low-Power, High-Speed Flash Technology: - 100,000 Flash endurance - > 40 year retention
- Fully Static Design
- Wide Operating Voltage Range: 2.0V to 5.5V
- Wide Temperature Range:
PIC16F84A Microcontroller IC
- Maximum CPU Frequency: 20 MHz
- Architecture: 8 bit
- Program Memory (Flash): 1.75 kB
- RAM: 68 byte
- Internal Oscillator: No
- ADC: No
- of Pins: 18
- Voltage: 2V - 6V
- 10,000 erase/write cycles Enhanced FLASH Program memory typical
- 10,000,000 typical erase/write cycles EEPROM Data memory typical
- EEPROM Data Retention > 40 years
- In-Circuit Serial Programmingâ„¢ (ICSPâ„¢) - via two pins
- Power-on Reset (POR), Power-up Timer (PWRT), Oscillator Start-up Timer (OST)
- Watchdog Timer (WDT) with its own On-Chip RC Oscillator for reliable operation
- Code protection
- Power saving SLEEP mode
- Selectable oscillator options
- Low power, high speed technology
- Fully static design
- Wide operating voltage range:
- Low power consumption:
PIC16F873A Microcontroller IC
- Maximum CPU Frequency: 20 MHz
- Architecture: 8 bit
- Program Memory (Flash): 7 kB
- RAM: 192 byte
- Internal Oscillator: No
- ADC: 1 (5 channels)
- of Pins: 28
- Voltage: 2V - 5.5V
- 100,000 erase/write cycle Enhanced Flash program memory typical
- 1,000,000 erase/write cycle Data EEPROM memory typical
- Data EEPROM Retention > 40 years
- Self-reprogrammable under software control
- In-Circuit Serial Programmingâ„¢ (ICSPâ„¢) via two pins
- Single-supply 5V In-Circuit Serial Programming
- Watchdog Timer (WDT) with its own on-chip RC oscillator for reliable operation
- Programmable code protection
- Power saving Sleep mode
- Selectable oscillator options
- In-Circuit Debug (ICD) via two pins
- Low-power, high-speed Flash/EEPROM technology
- Fully static design
- Wide operating voltage range (2.0V to 5.5V)
- Commercial and Industrial temperature ranges
- Low-power consumption
PIC16F887 Microcontroller IC
- Architecture: 8 bit
- Program Memory (Flash): 14 kB
- RAM: 368 byte
- Internal Oscillator: 8 MHz, 32 KHz
- ADC: 1 (14 channels)
- of Pins: 40
- Voltage: 2V - 5.5V
- Precision Internal Oscillator:
- Power-Saving Sleep mode
- Wide operating voltage range (2.0V-5.5V)
- Industrial and Extended Temperature range
- Power-on Reset (POR)
- Power-up Timer (PWRT) and Oscillator Start-up Timer (OST)
- Brown-out Reset (BOR) with software control option
- Enhanced low-current Watchdog Timer (WDT) with on-chip oscillator (software selectable nominal 268 seconds with full prescaler) with software enable
- Multiplexed Master Clear with pull-up/input pin
- Programmable code protection
- High Endurance Flash/EEPROM cell:
- Program memory Read/Write during run time
- In-Circuit Debugger (on board)
PIC18F4520 Microcontroller IC
- Maximum CPU Frequency: 40 MHz
- Architecture: 8 bit
- Program Memory (Flash): 32 kB
- RAM: 1536 byte
- Internal Oscillator: 8MHz, 32 KHz
- ADC: 1 (13 channels)
- of Pins: 40
- Voltage: 2V - 5.5V
- C Compiler Optimized Architecture: - Optional extended instruction set designed to optimize re-entrant code
- 100,000 Erase/Write Cycle Enhanced Flash Program Memory Typical
- 1,000,000 Erase/Write Cycle Data EEPROM Memory Typical
- Flash/Data EEPROM Retention: 100 Years Typical
- Self-Programmable under Software Control
- Priority Levels for Interrupts
- 8 x 8 Single-Cycle Hardware Multiplier
- Extended Watchdog Timer (WDT): - Programmable period from 4 ms to 131s
- Single-Supply 5V In-Circuit Serial Programmingâ„¢ (ICSPâ„¢) via Two Pins
- In-Circuit Debug (ICD) via Two Pins
- Wide Operating Voltage Range: 2.0V to 5.5V
- Programmable Brown-out Reset (BOR) with Software Enable Option