433mHz Transmitter Receiver RF Radio Module
- Range in open space(Standard Conditions) : 100 Meters
- RX Receiver Frequency: 433 MHz
- RX Typical Sensitivity: 105 Dbm
- RX Supply Current: 3.5 mA
- RX IF Frequency: 1MHz
- RX Operating Voltage: 5V
- TX Frequency Range: 433.92 MHz
- TX Supply Voltage: 3V ~ 6V
- TX Output Power: 4 ~ 12 Dbm
- Low Power Consumption
- Easy For RF-based Application
- Complete Radio Transmitter
- Transmit Range Up To 50m
- CMOS / TTL Input
- No Adjustable Components
- Very Stable Operating Frequency
- Low Current Consumption (Typ 11mA)
- Wide Operating Voltage
- ASK Modulation
5pcs x NFC Sticker tags 13.56MHz ISO14443A 25mm Ntag213 RFID NFC tag
- Chip: Ntag213.
- Physical capacity: 180 bytes.
- Usable capacity: 144 bytes.
- Protocol: ISO14443A.
- Working frequency: 13.56 MHZ.
- Reading and writing distance: 1 to 5 cm.
- Reading and writing time: 1 to 2 ms.
- Working temperature: -20 to 55 degrees, the humidity of 90%.
- Erase times : > 100000 times.
- Data storage: > 10 years.
- Reading time: 100000 times.
- Diameter: 25mm.
- Materials: PE self-adhesive + coated paper.
- Manufacturer programmed 7-byte UID for each device
- Preprogrammed Capability container with one-time programmable bits
- Field programmable read-only locking function
- ECC-based originality signature
- 32-bit password protection to prevent unauthorized memory operations
- NFC Forum Tag 2 Type compliance
PN532 NFC/RFID Controller Shield for Arduino
- PN532 chip-set
- Operating Voltage : 3.3V ~ 5v
- Support I2C, SPI
- I2C: 3.3V ~ 24V TTL
- SPI: 3.3V TTL with 100-ohm resistors in series
- Plug and play, Arduino compatible
- Built-in PCB Antenna
- Communication distance:10cm
- Easy to change mode
- NFC/RFID PN532 shield including a tuned 13.56MHz stripline antenna
- 36-pin 0.1" header for attaching the shield to an Arduino.
- Compatible with Arduino Mega 1280 & 2560, Diecimila, Duemilanove, and UNO
RF 433Mhz RX TX Encoder Decoder board [HT12E & HT12D IC]
- Operating voltage: 3.6~5.5v ( 5v recommended),
- Receiver sensitivity as high as -110dbm,
- Compatible with HT12E and HT12D,
- Low power and good range.
- High-frequency stability and low coherence and interference
- Easy interfacing with the RF modules, using the female headers for placing the modules.
- Breakout pins for connecting to the microcontroller.
- DIP Switch for Address Selection (when multiple modules are used at one location)
- Status LED for valid transmit.
- Supports both ASK, FSK RF modules
- Small size, high quality PCB.
RF Transmitter Receiver Module 315MHz Wireless
Transmitter Module
- Operating voltage: 3V to 12V
- Operating frequency: 433.92MHz; 315MHz
- Standby current: 0mA
- Operating current: 20mA to 28mA
- Transmission distance: >500m (open to receiving plate sensitivity at -103dBm distance of more than)
- Output power: 16dBm (40mW)
- Data transfer rate: <10Kbps
- Modulation mode: OOK (amplitude modulation)
- Operating temperature: -10℃ to +70℃
-
- Operating voltage: 5V DC
- Static current:4mA
- Receiver frequency: 433.92MHz; 315MHz
- Sensitivity: -105dB
- External antenna: 32CM single wire spiral
- No of pins: 4
RFID 13.56MHz Card
- Contactless transmission of data and supply energy (no battery needed)
- Operating distance: Up to 100mm (depending on antenna geometry)
- Operating frequency: 13.56MHz
- Data transfer: 106 kbit/s
- Data integrity: 16 Bit CRC, parity, bit coding bit counting
- Typical ticketing transaction: <100 ms ( including backup management)
- User-definable access conditions for each memory block
- Data retention of 10 years.
- Write endurance 100 000 cycles
- Reading and writing distance: 2.5-10CM
- Reading and writing time: 1-2MS
- Working temperature: -20 ° -85 °
- Packaging materials: PVC, PET, 0.13 coins
- Packaging technology: ultrasonic automatic line / automatic welding
- Production standards: ISO 14443, ISO 10536
RFID Key Fob 13.56mhz
- Operating frequency: 13.56 MHz
- Operating temperature: -45 °C to 85 °C
- Storage temperature: -55 °C to 100 °C
- Response Frequency: 13.56MHz
- Chip type: FM1108 Fudan Chip
- Memory capacity: 8 kbit
- Material: ABS
- Standard deployment: Attached to key fob and used for ID control
- For sensing and identifying tagged people and objects
- It is not re-programmable
- Dimension(LxWxH): 43.7×30.5×5.3mm
RFID Tag Key Fob Keyfobs 125Khz
- Material: ABS
- Response Frequency: 125Khz
- 2kbps ASK
- Diameter: ~29mm
- Range: 0-10 cm
- Manchester encoding
- 32-bit unique ID
- Uses TK4100 chip which is compatible with EM4100
- 64-bit data stream [Header+ID+Data+Parity]
- Read Time: 1-2ms
- Operating Temperature: -20c ~ 85 degree C
- Endurance:> 100,000 times
- 64-bit data stream [Header+ID+Data+Parity]
- Designed for the RFID 125KHZ duplicator. can copy all the ID card, such as Access Card, District Card, Parking etc
- Dimension: 43.7×30.5×5.3mm