I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
125 KHz RFID CARD THICK
₹50.00 Original price was: ₹50.00.₹35.00Current price is: ₹35.00. inc. GST
- Frequency: 125KHz
- Material used: PVC
- Thickness:0.8mm
- Reading range: up to 90 cm
- Storage capacity:64 bit
- Operating temperature: -10 degree to +50 degree c
- Can’t be reprogrammed
- Water-resistant
- Size: 85*55*1.8mm
- Weight: 9gm
This 125KHz RFID Card designed for Contactless transmission of data and supplies energy. It operates with no battery needed and operates at a distance range of up to 100mm depending on antenna geometry. This Card operates at a frequency of 125KHz and at a Data transfer speed of 106 kbit/s. Thus highly reliable and prominent cards used in identification and access control applications. It consists of a globally printed 18 digit unique UID number.
This card consists of an overlay and protective film which ensures anti-scratch and high resistant property. These are less affected by the radio signals and materials since these are always a common choice for identification purposes. It is compatible with standard ID access devices with the contactless transmission of data and also supplies energy. This read-only card cannot be programmed and also features data integrity with 16 Bit CRC, parity, bit coding bit counting which allows Anti-collision
These thin and thick cards made up of flexible polyvinyl chloride (PVC) laminate material. Thus these cards are widely used in ticketing transactions at a rate of <100 ms including backup management. These cards used for wireless non-contact communication using radio-frequency electromagnetic fields. Moreover, this RFID Â transfer data, for the purposes of automatically identifying and tracking tags attached to objects. The tags consist of electronically stored information.
APPLICATIONS:
- Office/home security
- Personal Identification
- Access Control,
- Anti-Forgery
- Interactive Toy And Production Control Systems etc.

Related products
“21PCS 6.0mm Colorful Silicone Rubber Heat Shrink Tube
- Nominal pressure: 600 V.
- Material: Polyolefin
- Inner diameter: 6 mm
- Shrinkage factor: 2: 1 (max. shorten to 1/2 of its delivery diameter)
- Length: 45 mm
- Minimum initial shrink temperature: + 70
- Minimum full shrink temperature: + 125 ℃
- Tensile strength: 10.4 MPa
- Dielectric strength: 15 kV / mm
- Cutting method: scissors or sharp Flammability knife: hardly flammable
- 7 colors in total: yellow, blue, black, green, red, white, transparent
- Sleeve Length 0.1 m
- Sleeve Internal Diameter 4.5 mm
- Long-lasting life.
- A convenient element for a technician or hobbits is a working stand, car or van.
- Very convenient and easy to use
- Weight: 290 g
5pcs x NFC Sticker tags 13.56MHz ISO14443A 25mm Ntag213 RFID NFC tag
- Chip: Ntag213.
- Physical capacity: 180 bytes.
- Usable capacity: 144 bytes.
- Protocol: ISO14443A.
- Working frequency: 13.56 MHZ.
- Reading and writing distance: 1 to 5 cm.
- Reading and writing time: 1 to 2 ms.
- Working temperature: -20 to 55 degrees, the humidity of 90%.
- Erase times : > 100000 times.
- Data storage: > 10 years.
- Reading time: 100000 times.
- Diameter: 25mm.
- Materials: PE self-adhesive + coated paper.
- Manufacturer programmed 7-byte UID for each device
- Preprogrammed Capability container with one-time programmable bits
- Field programmable read-only locking function
- ECC-based originality signature
- 32-bit password protection to prevent unauthorized memory operations
- NFC Forum Tag 2 Type compliance
MFRC522 RFID 13.56MHz
- Integrated MFRC522 module 13.56MHz RFID module
- Operating voltage: 2.5V to 3.3V
- Supports SPI, I2C protocol, UART communication
- Maximum data rate: 10Mbps
- Read range: 5cm
- Current consumption: 13-26 mA
- Power down mode consumption: 10mA
- Low cost and low voltage device
- Advanced modulation and demodulation concept completely integrated into all types of 13.56MHz passive contactless communication method and protocol
- 14443A compatible transponder signal
- Can be directly loaded into various reader molds
- Dimension: 12.3*11.9*3.8cm
- Weight: 20gm
PN532 NFC/RFID Controller Shield for Arduino
- PN532 chip-set
- Operating Voltage : 3.3V ~ 5v
- Support I2C, SPI
- I2C: 3.3V ~ 24V TTL
- SPI: 3.3V TTL with 100-ohm resistors in series
- Plug and play, Arduino compatible
- Built-in PCB Antenna
- Communication distance:10cm
- Easy to change mode
- NFC/RFID PN532 shield including a tuned 13.56MHz stripline antenna
- 36-pin 0.1" header for attaching the shield to an Arduino.
- Compatible with Arduino Mega 1280 & 2560, Diecimila, Duemilanove, and UNO
RFID 13.56MHz Card
- Contactless transmission of data and supply energy (no battery needed)
- Operating distance: Up to 100mm (depending on antenna geometry)
- Operating frequency: 13.56MHz
- Data transfer: 106 kbit/s
- Data integrity: 16 Bit CRC, parity, bit coding bit counting
- Typical ticketing transaction: <100 ms ( including backup management)
- User-definable access conditions for each memory block
- Data retention of 10 years.
- Write endurance 100 000 cycles
- Reading and writing distance: 2.5-10CM
- Reading and writing time: 1-2MS
- Working temperature: -20 ° -85 °
- Packaging materials: PVC, PET, 0.13 coins
- Packaging technology: ultrasonic automatic line / automatic welding
- Production standards: ISO 14443, ISO 10536
RFID Key Fob 13.56mhz
- Operating frequency: 13.56 MHz
- Operating temperature: -45 °C to 85 °C
- Storage temperature: -55 °C to 100 °C
- Response Frequency: 13.56MHz
- Chip type: FM1108 Fudan Chip
- Memory capacity: 8 kbit
- Material: ABS
- Standard deployment: Attached to key fob and used for ID control
- For sensing and identifying tagged people and objects
- It is not re-programmable
- Dimension(LxWxH): 43.7×30.5×5.3mm
RFID Tag Key Fob Keyfobs 125Khz
- Material: ABS
- Response Frequency: 125Khz
- 2kbps ASK
- Diameter: ~29mm
- Range: 0-10 cm
- Manchester encoding
- 32-bit unique ID
- Uses TK4100 chip which is compatible with EM4100
- 64-bit data stream [Header+ID+Data+Parity]
- Read Time: 1-2ms
- Operating Temperature: -20c ~ 85 degree C
- Endurance:> 100,000 times
- 64-bit data stream [Header+ID+Data+Parity]
- Designed for the RFID 125KHZ duplicator. can copy all the ID card, such as Access Card, District Card, Parking etc
- Dimension: 43.7×30.5×5.3mm
Speech Recognition System HM2007
- Input Voltage:9 to 15 V DC
- Use a commonly available 12V 500ma DC Adapter
- Output Data :8 bits at 5V Logic Level
- Any microcontroller like 8051, PIC or AVR can be interfaced to data port to interpret and implement specialized applications
- Self-contained standalone speech recognition circuit
- User-programmable
- Up to 20-word vocabulary of duration two-second each
- Multi-lingual
- Non-volatile memory back up with 3V battery on board. Will keep the speech recognition data in memory even after power off.
- Easily interfaced to control external circuits & appliances

Reviews
There are no reviews yet.