125 KHz RFID CARD THICK
5pcs x NFC Sticker tags 13.56MHz ISO14443A 25mm Ntag213 RFID NFC tag
- Chip: Ntag213.
- Physical capacity: 180 bytes.
- Usable capacity: 144 bytes.
- Protocol: ISO14443A.
- Working frequency: 13.56 MHZ.
- Reading and writing distance: 1 to 5 cm.
- Reading and writing time: 1 to 2 ms.
- Working temperature: -20 to 55 degrees, the humidity of 90%.
- Erase times : > 100000 times.
- Data storage: > 10 years.
- Reading time: 100000 times.
- Diameter: 25mm.
- Materials: PE self-adhesive + coated paper.
- Manufacturer programmed 7-byte UID for each device
- Preprogrammed Capability container with one-time programmable bits
- Field programmable read-only locking function
- ECC-based originality signature
- 32-bit password protection to prevent unauthorized memory operations
- NFC Forum Tag 2 Type compliance
MEPUNO COMMUNICATION BOARD
- Microcontroller ATMEGA328 P
- Crystal for microcontroller: 16 MHZ
- USB type B connector
- On-Board Power LED Indicator
- 5volt, 12 volt regulated circuit
- Two separate regulated 5volt power supply
- On Board On/Off switch
- On Board DC jack for powering up using adaptors
- On Board Reset Switch
- On Board TX/RX indication LEDs
- On board FTDI Driver for adruino
- Berg headers for external interfacing
- Supports I2C /GSM /GPS/RF/USART serial communication
- Separate berg headers available for PIR, Servo motor, RTC/I2C, GPS_TTL, and USART-TTL
- Four 3pin PBT Connectors
- Four SPDT 12V Relays
- Onboard DB9 connectors for GPS, GSM and USART communication
- Berg slot for 16x4 LCD connections
- Onboard TRIM-POT for LCD
- Onboard RTC IC: IN1307 with crystal 32768 MHZ crystal and CR2302 battery
PN532 NFC/RFID Controller Shield for Arduino
- PN532 chip-set
- Operating Voltage : 3.3V ~ 5v
- Support I2C, SPI
- I2C: 3.3V ~ 24V TTL
- SPI: 3.3V TTL with 100-ohm resistors in series
- Plug and play, Arduino compatible
- Built-in PCB Antenna
- Communication distance:10cm
- Easy to change mode
- NFC/RFID PN532 shield including a tuned 13.56MHz stripline antenna
- 36-pin 0.1" header for attaching the shield to an Arduino.
- Compatible with Arduino Mega 1280 & 2560, Diecimila, Duemilanove, and UNO
RFID 13.56MHz Card
- Contactless transmission of data and supply energy (no battery needed)
- Operating distance: Up to 100mm (depending on antenna geometry)
- Operating frequency: 13.56MHz
- Data transfer: 106 kbit/s
- Data integrity: 16 Bit CRC, parity, bit coding bit counting
- Typical ticketing transaction: <100 ms ( including backup management)
- User-definable access conditions for each memory block
- Data retention of 10 years.
- Write endurance 100 000 cycles
- Reading and writing distance: 2.5-10CM
- Reading and writing time: 1-2MS
- Working temperature: -20 ° -85 °
- Packaging materials: PVC, PET, 0.13 coins
- Packaging technology: ultrasonic automatic line / automatic welding
- Production standards: ISO 14443, ISO 10536
RFID EM18 125KHz RS232 Output
- Operating Voltage: 5V DC Supply
- Reading Distance: 6-10 cm.
- Read frequency: 125 kHz.
- EM4001 64 – bit RFID tag compatible.
- 9600bps ASCII output.
- Current : <50 mA
- Operating Frequency: 125 Khz
- This RFID Reader Module 125Khz is easy to use
- It is Low Cost
- It gives RS-232 and TTL Output
- Need a very less external component to drive
- TTL Level Compatible (Directly connected to the microcontroller)
- Small Buzzer & LED available to know about the card presence
- High-Quality PCB material & Original component only
- Dimension:32* 32* 8mm
RFID Key Fob 13.56mhz
- Operating frequency: 13.56 MHz
- Operating temperature: -45 °C to 85 °C
- Storage temperature: -55 °C to 100 °C
- Response Frequency: 13.56MHz
- Chip type: FM1108 Fudan Chip
- Memory capacity: 8 kbit
- Material: ABS
- Standard deployment: Attached to key fob and used for ID control
- For sensing and identifying tagged people and objects
- It is not re-programmable
- Dimension(LxWxH): 43.7×30.5×5.3mm
RFID Tag Key Fob Keyfobs 125Khz
- Material: ABS
- Response Frequency: 125Khz
- 2kbps ASK
- Diameter: ~29mm
- Range: 0-10 cm
- Manchester encoding
- 32-bit unique ID
- Uses TK4100 chip which is compatible with EM4100
- 64-bit data stream [Header+ID+Data+Parity]
- Read Time: 1-2ms
- Operating Temperature: -20c ~ 85 degree C
- Endurance:> 100,000 times
- 64-bit data stream [Header+ID+Data+Parity]
- Designed for the RFID 125KHZ duplicator. can copy all the ID card, such as Access Card, District Card, Parking etc
- Dimension: 43.7×30.5×5.3mm