I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
40EPS12 SCR 1200V 40A
₹215.00 Original price was: ₹215.00.₹200.00Current price is: ₹200.00. inc. GST
- Input Rectifier Diode
- Maximum Peak Reverse Voltage:Â 1200V
- Max. Average Forward Current:Â 40A
- Non-Repetitive Surge Current:Â 475A
- Max. Forward Voltage Drop:Â 1.1V
- Package:Â TO-247AC
40EPS12 SCR 1200V 40A series of silicon-controlled rectifiers specifically designed for medium power switching and phase control applications.. The highest repeating peak reverse voltage (VRRM) for these devices is 1200V, with a maximum average on-state current (IT(AV)) of 35A. The maximum DC gate current required to trigger (IGT) is only 150mA. The 40EPS12 is a versatile AC power rectification solution..
A four-layer solid-state current-controlling device known as a silicon-controlled rectifier or semiconductor-controlled rectifier. SCRs are unidirectional, meaning they can only carry current in one direction. TRIACs, on the other hand, are bidirectional (i.e. charge carriers can flow through them in either direction). TRIACs may be activated by either a positive or negative current running through the gate electrode, unlike SCRs, which are normally triggered by a positive current flowing into the gate.
APPLICATIONS
- Input rectification crowbar (soft start)
- AC switch in motor control
- UPS
- Welding
- Battery charge

Related products
4000W 220V AC SCR Voltage Regulator Dimmer Electric Motor Speed Controller
4000W AC CONTROLLER
5000W Thyristor Voltage Regulator, Adjust Light Speed Temperature
74LS540 High-Speed CMOS Logic Octal Buffer and Line Driver IC
APM/Pixhawk Power Module V6.0 Output BEC 3A XT60 Plug 28V 90A
- Input Voltage Range: 6-28V DC
- Output voltage: 5.3V ± 0.1V
- Maximum output current: 3A
- Maximum current: 90A
- Maximum voltage: 30V
- Supports from 2 cell to 6 cell battery.
- 6P cable can be directly connected to APM/Pixhawk flight control
- Additional 4P rows of pin-free to wire/PIN to connect to another flight control
- Voltage and current measurement configured for 5V ADC.
- Switching regulator outputs 5.3V and 3A max.
- Dimensions: 25mm x 21mm x 9mm
- Weight: 17gm
Capacitor Touch Dimmer, Constant Voltage LED Stepless Dimming, PWM Control Board
- Voltage range: 4V to 5V
- Maximum output current: 500mA
- Hole distance: 16 mm
- Aperture: 5 mm
- The lamp brightness can be adjusted by requirement, it is very to operate.
- It can touch in medium protection, such as glass, acrylic, plastic, ceramics, and so on, which is very safe.
- Anti power and phone interference, the EFT can reach above +/-2KV; the touch response sensitivity and reliability will not be affected by the close distance or multi-angle mobile phone interference.
- Dimming mode: Non-polar PWM dimming.
- PCB size: 23 x 20mm
DC 50A 75mV Current Shunt Resistor for Amp Meter Gauge
IR LED Sensor
- Size: 5mm LED
- Wavelength: 940nm wavelength (most commonly used)
- Forward current (IF) is 100mA (normal condition) and 300mA (max.)
- 5A of surge forward current
- 24v to 1.4v of forward voltage
- Temperature : -40 to 100 ℃
- Soldering Temperature should not exceed 260 ℃
- Power Dissipation of 150mW at 25℃ (free-air temperature) or below
- Spectral bandwidth of 45nm
- Viewing angle: 30 to 40 degree
- High Reliability
- Excessive radiant intensity
- Having lead spacing of 2.54mm
- Easy to use with breadboard or perf board

Reviews
There are no reviews yet.