I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
434MHz/315Mz TX & RX
₹300.00 Original price was: ₹300.00.₹250.00Current price is: ₹250.00. inc. GST
Transmitter
- Working voltage: 3V – 12V for max. power use 12V
- Working current: max Less than 40mA max , and min 9mA
- Modulation mode: ASK
- Working frequency: 433MHz
- Transmission power: 25mW
Receiver
- Working voltage: 5.0VDC
- Working current:≤5.5mA max
- Modulation method: OOK/ASK
- Working frequency: 433.92MHz
- Bandwidth: 2MHz
- Sensitivity: excel –100dBm (50Ω)
- Transmitting velocity: <9.6Kbps (at 315MHz and -95dBm)
This RF module designed based on an RF Transmitter and an RF Receiver operates at a frequency of 434 MHz. An RF transmitter transmits serial data input wirelessly through its antenna connected at pin4. It transmits signals at the rate of 1Kbps – 10Kbps. The module consists of a SAW resonator tuned for 433.xx MHz operation. Moreover, there is a switching transistor and a few passive components to perform the functions.
This Radio Frequency (RF) module operates on Amplitude Shift Keying (ASK) with transmitter/receiver (Tx/Rx). The Transmitter transmits this serial input through RF. Then the Receiver module receives the transmitted signal placed away from the source of transmission. Thus these RF signals transmitted at a particular frequency and a baud rate. The RF receiver receives the transmitted data only if it operating at the same frequency as that of the transmitter. Moreover, this RF module has a wide range of applications in a Car security system, Remote key-less entry, Garage door controller, Home security, Wireless mouse, Automation system.
The transmitter module consists of an RF tuned circuit and a couple of OP Amps to amplify the received carrier wave from the transmitter. This amplified signal is further fed to a PLL (Phase Lock Loop) which enables the decoder to “lock” onto a stream of digital bits which gives better-decoded output and noise immunity.
The transmitter is powered by Vcc at a range of DC voltage between 3.5V to 12V. Since the RF output is proportional to the supply voltage. Thus higher the voltage, the greater the range will be. Finally, the antenna pin meant for an external antenna. This RF module is often used with a pair of encoder/decoder. Thus the encoder encodes parallel data for transmission feed, while the decoder decodes the receiving signal. So HT12E-HT12D, HT640-HT648, etc. are some commonly used encoder/decoder pair ICs.
Pin Description
Transmitter Module:
- Ground (0V): GND
- Serial Data Input Pin: DATA
- Supply Voltage (5V): VCC
- Antenna Output Pin: ANT
Receiver Module:
- Ground (0V): GND
- Serial Data Output Pin: DATA
- Linear Output Pin: Not Connected NC
- Supply Voltage (5V): VCC
- Supply Voltage (5V): VCC
- Ground (0V): GND
- Ground (0V): GND

Related products
1 CHANNEL 5V RELAY
- 1 channel relay board
- Operating voltage: 5V
- Maximum current: 2 A
- Relay contact current capacity of 10A @250 V AC/10A@ 30V AC
- configured as SINGLE POLE DOUBLE THROW( SPDT)
- LED status indicates relay ON/OFF state.
- Standard TTL level logic controlled
- One normally closed and one normally opened contact
- Compatible with any 5V microcontroller
- Dimension: 43*17*17mm
- Weight: 150gm
2 CHANNEL 5V RELAY
- High current relay
- Two LED S to indicate relays ON/OFF status
- Low-level trigger expansion board
- Opto isolation circuitry
- Works with logic level signal 3.3V or 5V devices
- Can be used as normally open (NO) or normally closed (NC)
- Back EMF protection
- Ensures diode current protection
- AC control voltage: 250v @mx10A
- DC control voltage: 30V @max 10A
- Easy installation and fixing
3.3V/5V MB102 Breadboard Power Supply Module
- Input voltage: 6.5V to 12V
- Output voltage: 3.3V to 5V
- Output current: 700Ma
- Apply to MB102 breadboard
- Sorting jumpers used to switch voltage between 3.3V and 5V
- Onboard LED indicator to show the presence of power
- Short circuit protection
- Fits securely on standard 400 and 830 points on the breadboard
- Dimensions: 53*32*23mm
- Weight: 10gm
4 CHANNEL 12V RELAY
- 4-Channel relay interface board
- Relay input voltage: 12V DC
- Relay output: 5A/250V AC
- Signal input:5V DC from the microcontroller
- High current relay of 10A @250 V AC/10A@ 30V DC
- For quick and easy connection high-quality screw terminals provided
- Can control both AC & DC appliances such as DC motors, solenoid valves, lamps, etc.
- LED status indicates relay ON/OFF state.
- Power battery terminal for relay output and aux power connection
- Standard interface that can be controlled by a microcontroller (Arduino, 8051, PIC, AVR, DSP, ARM)
- Relay can directly control all equipment’s and loads
- For easy accessibility input signal pin connected to burg sticks
- Dimension: 165*65*1mm
- Weight: 7gm
Antenna GSM-2DBI (Spring)
- Gain: 2dBi
- Lower VSWR ≤ 2.0
- Signal stability.
- Cable Length: 3m
- Antenna Height: 28cm
- Polarization Vertical Impedance- 50 Ω
- Material: Metal
- Colour: Black
- Operation Temperature: -30~60 degree C
- Humidity: 5% to 95%
- Connector type: SMA Male Plug
- Compact size.
- Good appearance.
- Strong adaptability of environment.
- Package includes:
Antenna GSM-6DBI (Spring)
- Gain:6dBi
- Lower VSWR ≤ 2.0
- Signal stability.
- Cable Length: 3m
- Antenna Height: 28cm
- Polarization Vertical Impedance- 50 Ω
- Material: Metal
- Colour: Black
- Magnetic base
- Operation Temperature: -30~60 degree C
- Humidity: 5% to 95%
- Connector type: SMA Male Plug
- Compact size.
- Good appearance.
- Strong adaptability of environment.
GPS 3V Mount SMA-3M Cable
- Central Frequency: 1575.42 MHz /GPS External Active Antenna- 2 MHz
- Polarization: R.H.C.P
- Input Voltage: 3 V to 5 V
- Gain: 27 dB / 01 dB
- Embedded Magnet for easy mounting
- Water-Proof Design
- 5 M Cable with SMA Connector
- Operating Temperature: 20 to 85 degree C
- Bandwidth (min.): 9 MHz
- Storage Temperature: 50 to 120 degree C
- Relative Humidity: 0 % to 100 %Transmitter & Receiver
GPS Modem SKG13C External Antenna
- Operating voltage: 3.0V to 4.2V
- Ultra high sensitivity: -165dBm
- Extremely fast TTFF (Time To First Fix) at the low signal level
- Low power consumption: Typical 45mA@3.3V
- NMEA-0183 compliant protocol or custom protocol
- Operating temperature range: -40 to 85℃
- SMD type with stamp holes
- Small form factor: 15x13x2.7mm
- RoHS compliant (Lead-free)
- Support walk model

Reviews
There are no reviews yet.