I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
-12%
MAX7219 led module 8 digit 7 segment display
Original price was: ₹510.00.₹475.00Current price is: ₹475.00. inc. GST
VS1053 MP3 Recording Module Development Board with Onboard Recording For UNO
Original price was: ₹1,855.00.₹1,400.00Current price is: ₹1,400.00. inc. GST
5-36v Switch Drive High-power MOSFET Trigger Module
Original price was: ₹455.00.₹400.00Current price is: ₹400.00. inc. GST
- Operating Voltage: DC 5V – 36V;
- The trigger source: digital high-low (DC3.3V – 20V), can be connected microcontroller IO port, PLC interfaces, DC power, you can access the PWM signal, the signal frequency 0–20KHZ perfect support.
- Output capacity: DC 5V – 36V, at room temperature, continuous current 15A, power 400W! Lower auxiliary cooling conditions, the maximum current up to 30A.
- Applications: You can control the output of power equipment, motors, light bulbs, LED lights, DC motors, micro-pumps, solenoid valves, etc.. You can enter
- PWM, motor speed control, lamp brightness.
- Availability: unlimited switch
- Operating temperature: -40-85
- Dimension: 34mm x 17mm x 12mm
- The use of imported dual-MOS parallel active output, lower resistance, more current, strong power at room temperature, 15A, 400W, to meet the most use of the equipment
- Wide voltage, the perfect support for PWM
- Easily control high power devices
- Input PWM to achieve motor speed control, lamp brightness control
Description
This 5-36v Switch Drive High-power MOSFET Trigger Module can control the output of power equipment, motors, light bulbs, LED lights, DC motors, micro-pumps, solenoid valves, PWM, motor speed control, lamp brightness. etc.
The 5-36V switch drive module provides high power MOS trigger switch driver module and control board with a field-effect tube to adjust the electronic switch. It adopts imported double MOS parallel active output to show lower internal resistance, greater electric current, and power.
Besides it works at 15A, 400W under a common temperature which satisfies most devices usage and realizes the control of great power devices in a relaxed way. Moreover, applied to power devices which controlled by output terminals like electric motors and light bulbs to control the speed of the motor and the light of bulbs.
The use of imported dual-MOS parallel active output, lower resistance, more current, strong power at room temperature, 15A, 400W, to meet the most use of the equipment. Wide voltage, the perfect support for PWM. Easily control high power devices. Hence Input PWM used to achieve motor speed control, lamp brightness control.
Reviews (0)
Shipping & Delivery
Related products
16-Channel 12-bit PWM/Servo Driver I2C interface PCA9685 for Arduino Raspberry Pi
- Adjustable frequency PWM up to about 1.6 kHz
- 12-bit resolution for each output – for servos, that means about 4us resolution at a 60Hz update rate
- Configurable push-pull or an open-drain output
- The output enable pin to quickly disable all the outputs
- Terminal block for power input
- Reverse polarity protection on the terminal block input
- Green power-good LED
- 3 pin connectors in groups of 4 so you can plug in 16 servos at once
- Chainable design
- A spot to place a big capacitor on the V+ line
- 220-ohm series resistors on all the output lines to protect them, and to make driving LEDs trivial.
- This board/chip uses an I2C 7-bit address between 0x60-0x80, selectable with jumpers.
A3967 STEPPER MOTOR DRIVER
- A3967 precision micro-stepping driver
- Power supply: 7v to 30v
- Logic voltage: 5v to 3.3v
- Higher the voltage higher the torque at high speed
- Adjustable current control from 150Ma/ phase to 750ma phase
- Automatic current decay mode detection/selection
- Fast, slow, and mixed current decay modes
- Internal UVLO and thermal shutdown circuitry
- Crossover current protection
- Micro stepping resolution to full, half, quarter, and eighth steps by broken out MS1 and MS2 pins.
- Compatible with Arduino, GRBL G-Code interpreter for driving3-axis CNC machines
- Salington sink drivers used
- Compactible with 4, 6,8 wire stepper motor of any voltage
A4988 Stepper Motor
- Operating voltage supply: 8 V to 35 V
- Continuous current per phase: 1 Amp
- Maximum current per phase: 2 Amp
- Minimum logic voltage: 3V
- Maximum logic voltage: 5.5V
- Microstep resolutions: Full, 1/2, 1/4, 1/8, and 1/16
- Logic Voltage supply: 3.3 V to 5 V
- Compatible with 3V3 and 5V microcontrollers
- Our Board comes with 0.1 Ohm Sensor resistors
- Five different step resolutions: full-step, half-step, quarter-step, eighth-step, and sixteenth-step
- The Correct current decay mode (fast decay or slow decay) is selected by chopping the control
- Over-temperature thermal shutdown, under-voltage lockout, and crossover-current protection
- Short-to-ground and shorted-load protection
- 4-layer, 2 oz copper PCB for improved heat dissipation
- Exposed solderable ground pad below the driver IC on the bottom of the PCB
Dual Monster Moto Shield VNH2SP30 Motor Driver 2x14A (Peak 30A)
- Driver Model: VNH3ASP30
- Current sensing available to Arduino analogue pin
- Operating Voltage: 12 V to 16V DC
- Peak Current: 14A
- Continuous Current: 30A
- of Channels: 2
- Maximum PWM frequency: 20 kHz
- MOSFET on-resistance: 19 m (per leg)
- Thermal Shutdown protection
- Under-voltage and Overvoltage shutdown.
- LED Indicator
- Dimensions: 60 x 54 x 12mm
- Weight: 19gm
IR LED Sensor
- Size: 5mm LED
- Wavelength: 940nm wavelength (most commonly used)
- Forward current (IF) is 100mA (normal condition) and 300mA (max.)
- 5A of surge forward current
- 24v to 1.4v of forward voltage
- Temperature : -40 to 100 ℃
- Soldering Temperature should not exceed 260 ℃
- Power Dissipation of 150mW at 25℃ (free-air temperature) or below
- Spectral bandwidth of 45nm
- Viewing angle: 30 to 40 degree
- High Reliability
- Excessive radiant intensity
- Having lead spacing of 2.54mm
- Easy to use with breadboard or perf board
L293D MOTOR DRIVER
- Can be used to run two dc motors with the same IC
- Speed and direction control is possible
- Supply voltage: 4.5 V to 7V
- Motor voltage: 4.5 v to 36v
- Maximum peak motor current: 1.2 A
- Maximum continuous motor current: 600 milli ampere
- Screw terminal connectors for easy connection
- Transition time: 300 ns (at 5v and 24v)
- High noise immunity inputs
- Automatic thermal shutdown
- Available in 16 pin DIP, TSSOP, SOIC package
- Dimension: 48*34*14mm
- Weight: 15gm
Leadshine DM542
- Good high-speed performance
- Supply voltage up to +50VDC
- Output current up to 4.2A
- Pulse frequency up to 300 KHz
- Extremely cost-effective
- Automatic idle-current reduction
- 3-state current control technology
- Self-adjustment technology
- Pure-sinusoidal current control technology
- TTL compatible and optically isolated input
- 15 selectable resolutions in decimal and binary, up to 25,600 steps/rev
- Suitable for 2-phase and 4-phase motors
- DIP switch current setting with 8 different values
- Support PUL/DIR and CW/CCW modes
- Short-voltage, over-voltage, over-current protection
TB6560 4 Axis Stepper Motor Driver
- Driver Chip: TB6560AHQ
- Operating Voltage: 10-35V
- Nominal Voltage: 24V
- Stepper motor drive current: 1.5A - 3A/phase
- With the large heat sink to ensure good heat dissipation
- Double-pole constant flow PWM actuation output
- 6N137 high-speed OptoCoupler, to ensure a high speed without stepping out.
- Compatible Stepper motors: 2/4 Phase, 4/6/8 leads stepper motors within 3.5A
- 1 - 1/16 micro step setting - higher accuracy, smoother operation
- Full closed-type optical isolation to protect the user's computer and equipment
- Professional design, two-stage signal processing, super anti-jamming
- Bipolar constant current chopper drive motor low-speed non-creeping phenomenon, noise, non-resonant region
- Four input control
-
Reviews
There are no reviews yet.