I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
74HC21 Dual 4-Input AND Gate IC
₹20.00 Original price was: ₹20.00.₹15.00Current price is: ₹15.00. inc. GST
- Dual 4-input AND gate
- Logic Family:Â 74HC
- No. of Gates:Â 2
- No. of Pins:Â 14
- Propagation Delay Time:Â 110 ns
- Number of Lines In/Out:Â 4 / 1
- Output Current:Â 5.2mA
- Operating Temperature Range: -40°C to +1250C
- Supply Voltage Range:Â 2V-6V
- Package:Â DIP-14
74HC21 is Quad 4-Input AND circuit manufactured in 14 Pin IC package. The 74HC21 provides 4 independent 2-input AND gates with standard push-pull outputs. The 74HC21 designed as an advanced high speed CMOS 2 Input AND circuit fabricated with silicon gate CMOS technology. It achieves a high−speed operation similar to equivalent Bipolar Schottky TTL while maintaining the CMOS low power dissipation. The interior circuit composed of 4 stages including buffer output, provides high noise immunity and stable output. An input protection circuit ensures that 0 V to 7 V are often applied to the input pins without reference to the supply voltage. This device often accustomed to interface 5 V to 3 V systems and two supply systems like battery backup. This circuit prevents device destruction thanks to mismatched supply and input voltages.
The 74HC21 logic family is functionally also as pin-out compatible with the quality 74LS logic family. It has an operating voltage range from 2V to 6V and consumes only 20uA of current. 74HC21 inverter IC utilizes advanced silicon-gate CMOS technology to realize operating speeds almost like LS-TTL gates with the low power consumption of ordinary CMOS integrated circuits. The 74HC21 has buffered outputs, providing high noise immunity and therefore the ability to drive 10 LS-TTL loads. All inputs shielded from damage due to static discharge by internal diode clamps to VCC and ground. They are specified in compliance with JEDEC standard no. 7A.
Applications
- Combining power good signals
- Enable digital signals

Related products
120pcs 12 value 1uF-470uF Electrolytic Capacitor Kit 1UF 2.2UF 3.3UF 4.7UF 10UF 22UF 33UF 47UF 100UF 220UF
120pcs 12 values 0.22UF-470UF Aluminum electrolytic capacitor assortment kit set pack
5-36v Switch Drive High-power MOSFET Trigger Module
- Operating Voltage: DC 5V - 36V;
- The trigger source: digital high-low (DC3.3V - 20V), can be connected microcontroller IO port, PLC interfaces, DC power, you can access the PWM signal, the signal frequency 0--20KHZ perfect support.
- Output capacity: DC 5V - 36V, at room temperature, continuous current 15A, power 400W! Lower auxiliary cooling conditions, the maximum current up to 30A.
- Applications: You can control the output of power equipment, motors, light bulbs, LED lights, DC motors, micro-pumps, solenoid valves, etc.. You can enter
- PWM, motor speed control, lamp brightness.
- Availability: unlimited switch
- Operating temperature: -40-85
- Dimension: 34mm x 17mm x 12mm
- The use of imported dual-MOS parallel active output, lower resistance, more current, strong power at room temperature, 15A, 400W, to meet the most use of the equipment
- Wide voltage, the perfect support for PWM
- Easily control high power devices
- Input PWM to achieve motor speed control, lamp brightness control
Capacitor Touch Dimmer, Constant Voltage LED Stepless Dimming, PWM Control Board
- Voltage range: 4V to 5V
- Maximum output current: 500mA
- Hole distance: 16 mm
- Aperture: 5 mm
- The lamp brightness can be adjusted by requirement, it is very to operate.
- It can touch in medium protection, such as glass, acrylic, plastic, ceramics, and so on, which is very safe.
- Anti power and phone interference, the EFT can reach above +/-2KV; the touch response sensitivity and reliability will not be affected by the close distance or multi-angle mobile phone interference.
- Dimming mode: Non-polar PWM dimming.
- PCB size: 23 x 20mm
Dean Connector
- Male plug size: About 13* 7* 19mm
- Female plug size: About 13* 7* 15mm
- Current Rating: 30Amps
- Colour: Red and golden
- Material: Plastic and metal
- Provides a secure connection for battery and motor connections
- Eliminates the possibility of wrong polarity connections
- Used in RC hobby, car, boat, plane, helicopter, LIPO battery, etc.
- Dimension: 9x0.7x2cm
- Weight:20gm
Dual Micro USB 3.7v to 5V 2A Power Bank DIY 18650 LiPo Charger
- 4-level LED lamp display power, not working state intelligent automatic shutdown;
- The built-in lithium battery protection IC, over-current, under-voltage protection;
- Dual USB output ports.
- Dimensions: 68 x 34 x 9 mm (LxWxH)
- Weight: 10 gm
- Input port: MicroUSB (Andro)
- Input requirements: 5V constant voltage power supply can do charge input power, the most matching charger for 5v1a above
- Output port: USB
- Output parameters: 5V1A/5V2A
- Requirements for rechargeable batteries:
- Compatible Batteries: 18650 batteries, cell phone batteries, flat-panel batteries, MP3 batteries, etc. 3.7v-4.2V polymer Lithium battery,
GSM Antenna Dlenp 2dbi/3dbi Patch Antenna with SMA Male Connector
- GSM Antenna
- Gain: 2 to 3dbi
- Wire Length: 3 metre
- 3dbi Sticker Antenna
- GSM Antenna
- SMA Male Connector
- Frequency Range(MHz): 824-960/1710-1990Mhz
- Bandwidth (MHz): 136/280
- VSWR≤1.5
- Gain(dB): 2-3dbi
- Max Input power(W): 60W
- Input Impedance: 50 Ω
- Polarization Type: Vertical
- Cable Type: RG174
- Mounting Adhesive
- Net weight: 47g
XT60 Connector
- Manufacturer: AMASS
- Connector Series: XT60H
- Rated Voltage: DC 500V
- Metal Material: Brass Gold Plated
- Rated Current: 30A
- Momentary Current: 60A
- Number of pins: 2
- Colour: Yellow
- Contact Resistance: 0.55mΩ
- FR Level: UL94 V0
- Use Times: 1000 TIMES
- Temperature: -20℃ to 120℃
- Spatial Orientation Straight
- Compatible for Wire size up to 12AWG
- Mechanical mounting for cable
- Electrical mounting soldered
- Contact plating Gold flash

Reviews
There are no reviews yet.