I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
74HC21 Dual 4-Input AND Gate IC
₹20.00 Original price was: ₹20.00.₹15.00Current price is: ₹15.00. inc. GST
- Dual 4-input AND gate
- Logic Family:Â 74HC
- No. of Gates:Â 2
- No. of Pins:Â 14
- Propagation Delay Time:Â 110 ns
- Number of Lines In/Out:Â 4 / 1
- Output Current:Â 5.2mA
- Operating Temperature Range: -40°C to +1250C
- Supply Voltage Range:Â 2V-6V
- Package:Â DIP-14
74HC21 is Quad 4-Input AND circuit manufactured in 14 Pin IC package. The 74HC21 provides 4 independent 2-input AND gates with standard push-pull outputs. The 74HC21 designed as an advanced high speed CMOS 2 Input AND circuit fabricated with silicon gate CMOS technology. It achieves a high−speed operation similar to equivalent Bipolar Schottky TTL while maintaining the CMOS low power dissipation. The interior circuit composed of 4 stages including buffer output, provides high noise immunity and stable output. An input protection circuit ensures that 0 V to 7 V are often applied to the input pins without reference to the supply voltage. This device often accustomed to interface 5 V to 3 V systems and two supply systems like battery backup. This circuit prevents device destruction thanks to mismatched supply and input voltages.
The 74HC21 logic family is functionally also as pin-out compatible with the quality 74LS logic family. It has an operating voltage range from 2V to 6V and consumes only 20uA of current. 74HC21 inverter IC utilizes advanced silicon-gate CMOS technology to realize operating speeds almost like LS-TTL gates with the low power consumption of ordinary CMOS integrated circuits. The 74HC21 has buffered outputs, providing high noise immunity and therefore the ability to drive 10 LS-TTL loads. All inputs shielded from damage due to static discharge by internal diode clamps to VCC and ground. They are specified in compliance with JEDEC standard no. 7A.
Applications
- Combining power good signals
- Enable digital signals

Related products
1/4W 5% Assorted Value Carbon Film Resistor Assortment Kit Set pack electronic diy kit
- 100% brand new and high quality.
- Fine workmanship and long service life.
- 1/4W carbon film resistor package.
- High precision and stability.
- Easy to use.
- Precision: 5%
- Error: 5%
- Values
- 10Ω, 15Ω, 22Ω, 33Ω, 47Ω, 68Ω, 100Ω, 220Ω, 330Ω, 470Ω, 1k, 1k5, 2k2, 3k3, 4k7, 5k6, 6K8, 8K2, 10K, 15K, 22K, 33K, 47K, 56K, 68K, 100K, 150K, 220K, 330K, 470K
- Package included: 150pcs
4 Pin RMC Connector
5 Pin RMC Connector
Capacitor Touch Dimmer, Constant Voltage LED Stepless Dimming, PWM Control Board
- Voltage range: 4V to 5V
- Maximum output current: 500mA
- Hole distance: 16 mm
- Aperture: 5 mm
- The lamp brightness can be adjusted by requirement, it is very to operate.
- It can touch in medium protection, such as glass, acrylic, plastic, ceramics, and so on, which is very safe.
- Anti power and phone interference, the EFT can reach above +/-2KV; the touch response sensitivity and reliability will not be affected by the close distance or multi-angle mobile phone interference.
- Dimming mode: Non-polar PWM dimming.
- PCB size: 23 x 20mm
Dean Connector
- Male plug size: About 13* 7* 19mm
- Female plug size: About 13* 7* 15mm
- Current Rating: 30Amps
- Colour: Red and golden
- Material: Plastic and metal
- Provides a secure connection for battery and motor connections
- Eliminates the possibility of wrong polarity connections
- Used in RC hobby, car, boat, plane, helicopter, LIPO battery, etc.
- Dimension: 9x0.7x2cm
- Weight:20gm
IR LED Sensor
- Size: 5mm LED
- Wavelength: 940nm wavelength (most commonly used)
- Forward current (IF) is 100mA (normal condition) and 300mA (max.)
- 5A of surge forward current
- 24v to 1.4v of forward voltage
- Temperature : -40 to 100 ℃
- Soldering Temperature should not exceed 260 ℃
- Power Dissipation of 150mW at 25℃ (free-air temperature) or below
- Spectral bandwidth of 45nm
- Viewing angle: 30 to 40 degree
- High Reliability
- Excessive radiant intensity
- Having lead spacing of 2.54mm
- Easy to use with breadboard or perf board
Solid State Relay Module DC To AC SSR-40DA 3-32VDC/24-380VAC 40A
- Control mode: DC-AC
- Input voltage: 3-32V DC.
- Output voltage: 24-380V AC.
- Output current: 40A.
- Working voltage: 250V.
- Material: plastic + metal.
- Loading current: 40A
- Control current: 3-25mA DC
- On voltage: ≤1.5V AC
- One-off Time: ≤10ms
- Off Leakage Current: ≤2mA
- Dielectrics voltage-resistance: 2500VAC
- Environment temperature: -30 to +75
- Long service life and high reliability.
- Reduced electromagnetic interference.
- Highly reliable, compact size designed to offer users maximum simplicity.
Solid State Relay Module SSR-25DA 25A /250V 3-32V DC Input 24-380VAC Output
- Control mode: DC-AC
- Input voltage: 3-32V DC.
- Output voltage: 24-380V AC.
- Output current: 25A.
- Working voltage: 250V.
- Material: plastic + metal.
- Environment temperature: -30 to +75
- Long service life and high reliability.
- Reduced electromagnetic interference.
- Highly reliable, compact size designed to offer users maximum simplicity.
- Dimension: 6. 5Cm x 4. 5Cm x 2. 2Cm

Reviews
There are no reviews yet.