I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
Motor for Micro FPV RC Quadcopter
₹200.00 Original price was: ₹200.00.₹150.00Current price is: ₹150.00. inc. GST
- Motor Diameter: 8.5mm
- Motor Length: 20mm
- Shaft Diameter: 1.0mm
- Cable Length: 60mm
- Weight: about 5g
- Operating Voltage range: 3v to 3.7v DC
- Rated Speed – 39000 RPM
- Propeller length: 75mm
- This coreless motor supports 1S battery.
- Ideal for mini quadcopter projects weighing below 60 grams
Propeller is designed as a lightweight brushed DC coreless motor. These coreless motor works perfectly for a small drone, offering you an excellent affordable price when compared with costly BLDC motors. This Magnetic Micro Coreless Motor for Micro FPV RC Quadcopter is a very compact and lightweight DC motor nicely crafted for perfectly matching your small 100mm multirotor frames. This coreless motor comes with high-quality magnets and supports a 1s battery.
This is much more required to lift and push the drone to the target. And these are less noisy with low resistance. The only disadvantage of using coreless is the amount of torque they provide, as they are High Speed and Low Torque motors.
Propellers are designed as high-quality propellers explicitly for Micro FPV RC Quadcopter. These Props are lightweight and of high strength providing an angle of 15° design at the end of the propeller. These propellers are widely used for lower RPM motor and slow-flying drone models. The wide and thin blades of the propeller in their size category make them highly flexible in crash conditions. Thus they do not break easily. Propellers Black especially draws a larger amount of currents. And as a result, gives a considerable amount of thrust for the quadcopters.

Related products
30AMPS ESC DYS
- Input Voltage: 11.1 ~ 11.7 V.
- Constant Current: 30A (Max 40A<10s).
- BEC: 5V/3A.
- Li-Po battery: 2S ~ 3S.
- Ni-MH 4-10 CELLS Auto Detect.
- Separately voltage regulator IC for the microprocessor, providing good anti-jamming capability.
- Used with SimonK updated firmware for Multicopter
- Battery side – Male deans (T) connector.
- Motor side – Female 3.5mm gold connector.
- 30A ESC for BLDC has onboard BEC.
- Developed specifically for multi-rotor use
- Smooth, linear, and precise throttle response
- Extreme low output resistance, super current endurance
- Auto Low Battery Slow down at 3.0V/cell Lipo, cut-off at 2.9V/cell lipo.
- Supported motor speed (Maximum): 210000 RPM (2 poles), 70000 RPM (6 poles), 35000 RPM (12 poles).
- Dimension: 46* 26 * 11mm
- Weight: 23g
Acrylic Bracket for OV7670 Camera Module
DC 3.7V 7mm x 16mm Magnetic Micro Coreless Motor + Propeller
EMAX BLHELI 12Amp ESC for Quadcopter / Drones
- Based on BL Heli firmware.
- ESC Type: Brushless.
- Built in linear or switched BEC.
- Constant Current: 12A
- Burst Current: 15A
- BEC Mode: Linear BEC : 5v / 1A
- Lipo Cells: 2-4
- Constant Current: 12A.
- Support: One-shot 125 Protocol.
- Includes low voltage protection, over heat protection, and self-check functions.
- Separate power supply for MCU and BEC, helping eliminate magnetic interference.
- Fully programmable by any standard programming card or directly from your transmitter.
- Customisable throttle range.
- Weight: 11g
- Dimension: 42x20x8mm
KFL08 Zinc Alloy Pillow Block Flange Bearing 8mm Inner Diameter Flange Bearing
- Model Number: KFL08
- Material: Zinc Alloy
- Inner diameter: 8mm
- Length: 48mm
- Height: 12mm
- It inserts in housing work as a unit bearing.
- Housing is mainly casting or pressed steel.
- Bearing units are compact in design with perfect sealing devices.
- Light weight and high finish as it is made from Zinc Alloy.
- Anti-corrosive properties due to the high quality alloy material.
- Very stable even at high speeds of rotation.
- Low Noise generation even at higher speeds.
- Highly durable and long life in industrial working conditions.
- The bearing is closed on both sides to prevent dust and contamination.
- Weight: 26.4g
Landing Gear
MARSPOWER MX1806 2280KV BLDC Motor
- VK: 2280
- Max thrust: 460g
- No of cells: 2-3S
- Framework: 12N14P
- Suitable Propeller: 5-6”
- Shaft: 2mm
- Minimum ESC Specification: 12A Suggested
- Durable with high quality
- The 0.2mm core to lower load temperature and increase efficiency
- Range of use for DJI F330 ZMR250 H250
- Do every single motor balancing test
- Japan NMB bearings provide low noise and long life
- 2mm spindle selection of Kawasaki, Japan, more efficient, less heat
- NdFeB magnets temperature selection
- MX1806 (positive thread motor)
- FPV all configurations life 7-8 minutes!
- Easy to loosen the nut bombing risk!
- Low centre of gravity design
- Long-endurance design
- Dimension: 26.7*23mm
- Weight: 18gm
Power Distribution Board
- Material: glass fiber
- Easy connections from the battery to your ESC, video Transmitter, Flight Controller,
- LED power indicators
- Switches to control LEDs, video Transmitter power, etc.
- Can connect 1-8 ESC.
- Onboard switching voltage regulator
- Hole Spacing: 45mm Square and 35mm Square (Compatible with KK 45mm spacing)
- Dimensions : 50 x 50 x 2 mm.
- Weight: 8 gm.

Reviews
There are no reviews yet.