I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
CT1270 AC/DC Current Sensor
- Supply voltage: 5v DC
- Output: Analog Dc Voltage
- Small size
- Pass Wire Through Hole
- Get DC analogue Voltage Vcc and GND
- Compatible with Arduino, Raspberry Pi, AVR, ARM,8051, PIC
Description
A current sensor is designed to detect electric current AC/DC in a wire and thus generates a signal proportional to it. This generated signal could be analogue voltage or current or even digital output. Current Sensor basically used to measure and calculate the amount of current applied to the conductor without affecting the performance of the system. This current sensor operates at a supply voltage of 5V in which output is proportional to AC or DC current. CT1270 is used in a wide range of applications where sensing and controlling current flow is fundamental such as displaying the measured current in an ammeter. And also stored for further analysis in a data acquisition system or can be utilized for control purposes.
The present output current signal is read via the analogue I / O port of a microcontroller or an Arduino. Moreover, this current sensor module works perfectly with Arduino, Raspberry pi, AVR, ARM,8051, PIC and can be interfaced easily.
APPLICATIONS
- Ammeters
- Current control purposes
Reviews (0)
Shipping & Delivery
Related products
Current Sensor ACS712 20AMPS
- Supply Voltage: 4.5V ~ 5.5V DC
- Measure Current Range: 20A
- Sensitivity: 100mV/A
- The low-noise analogue signal path
- Device bandwidth is set via the new FILTER pin
- 5 µs output rise time in response to step input current
- Small footprint, low-profile SOIC8 package
- 1 kV RMS minimum isolation voltage from pins 1-4 to pins 5-8
- Small footprint, low-profile SOIC8 package
- 1 kV RMS minimum isolation voltage from pins 1-4 to pins 5-8
- Output voltage proportional to AC or DC currents
- Factory-trimmed for accuracy
- Extremely stable output offset voltage
- Nearly zero magnetic hysteresis
- The ratiometric output from the supply voltage.
DS18B20 PROBE
- Usable temperature range: -55 to 125°C (-67°F to +257°F)
- 9 to 12-bit selectable resolution
- Uses 1-Wire interface- requires only one digital pin for communication
- Unique 64 bit ID burned into a chip
- Multiple sensors can share one pin
- ±0.5°C Accuracy from -10°C to +85°C
- Temperature-limit alarm system
- Query time is less than 750ms
- Usable with 3.0V to 5.5V power/data
- Each pin uses a heat-shrinkable tube to prevent short circuit, internal sealing glue.
- Stainless steel tube encapsulation waterproof moistureproof prevents rust.
- Stainless steel tube 6mm diameter by 30mm long.
- Contains DS18B20 temperature sensor.
- Uses 1-Wire interface- requires only one digital pin for communication.
- Unique 64 bit ID burned into the chip.
- Multiple sensors can share one pin.
- Temperature-limit alarm system.
- Without the external components, the unique single bus.
Force Sensor 38.1mm
- Easily customizable to a wide range of sizes
- Cost-effective
- Ultra-thin; 0.45 mm
- Life: up to 10 million actuations
- Simple and easy to Integrate.
- Actuation Force: 0.1 Newtons
- Force Sensitivity Range: 0.1 - 10.02 Newtons
- Non-Actuated Resistance: 10M W
- Device Rise Time: <3 microseconds
- Temp Operating Range: 30 - +70 ºC
- 16MHz Clock Speed
- 32 KB Flash Memory
- Overall length: 1.75 inches
- Overall width: 0.28 inch
- Sensing area: 0.3 inch
LM35 SENSOR
- Calibrated Directly in Celsius (Centigrade)
- Operates from 4 V to 30 V
- Linear + 10-mV/°C Scale Factor
- ±0.5°C Ensured Accuracy (at 25°C)
- Can measure temperature ranging from -55°C to 150°C
- Less than 60-µA Current Drain
- Low Self-Heating, 0.08°C in Still Air
- Non-Linearity Only ±¼°C Typical
- Low-Impedance Output, 0.1 Ω for 1-mA Load.
- Drain current is less than 60uA
- The output voltage is directly proportional (Linear) to temperature (i.e.) there will be a rise of 10mV (0.01V) for every 1°C rise in temperature
- Suitable for Remote Applications
- Low-cost temperature sensor
- Available in TO-92, TO-220, TO-CAN, and SOIC package
MQ7 GAS SENSOR
- Operating Voltage: 3.3 – 5V.
- Type: Analog Sensor.
- Can detect the presence of carbon monoxide
- Heating voltage (high): 5V ± 0.1
- Heating voltage (low): 1.4V ± 0.1
- Load resistance: Adjustable
- Heating resistance: 33Ω ± 5%
- Heating time (high): 60 ± 1 seconds
- Heating time (low): 90 ± 1 seconds
- Heating consumption: About 350mW
- Using temperature: -20°C-50°C
- Storage temperature: -20°C-50°C
- Relative humidity: Less than 95%RH
- Oxygen concentration: 21%(stand condition) the oxygen concentration can affect the sensitivity characteristic
- Stable, long life and low cost
- Good sensitivity to Combustible gas in a wide range
MQ8 GAS SENSOR
- Operating Voltage: 3.3 – 5V.
- Type: Analog Sensor.
- Detection range: 100~1000ppm(H2 gas)
- Heating voltage (high): 5V ± 0.1
- Heating voltage (low): 1.4V ± 0.1
- Load resistance: Adjustable
- Heating resistance: 31Ω ± 5%
- Heating consumption: less than 800mW
- Using temperature: -20°C-50°C
- Storage temperature: -20°C-50°C
- Relative humidity: 55%+-5%RH
- High Sensitivity for Hydrogen
- Small sensitivity to alcohol, LPG, cooking fumes
U Slot Sensor MOC7811
- Model HY860D
- Output Type Photo Transistor
- Peak Emission Wavelength: 940nm
- IR Diode Forward Current: 50mA
- IR Diode Reverse Voltage: 5V
- Transistor Power Dissipation: 75mW
- Transistor Collector Current: 20mA
- Photo Transistor Collector-emitter Voltage: 30V
- Photo Transistor Emitter-collector Voltage: 5V
- Diode Power Dissipation: 100mW
- Operating Temperature Range: -55~100 Celsius Degree
- Number of Pins 4
- Hole Diameter: 3mm
- Material: Plastic, Metal
- Non-Contact Switching
- For Direct PC-Board or Dual-In-Line Socket Mounting
- Fast Switching Speed
- Colour: Black
- Dimension: 22 x 22 x 6mm
- Weight: 8gm
YF G1 Water Flow Sensor
- Working Voltage: DC 4.5V
- Working Voltage: DC 5V~18V
- Flow Rate Range: 2~100L/min
- Water pressure resistance: = >2MPa
- Operating Temperature: = -20~85C
- Insulation resistance: = >100MΩ
- Characteristics of Flow pulse: f=(4.8*Q) Q=L/Min
- Accuracy: ±3%
- Compact, Easy to Install
- High Sealing Performance
- High-Quality Hall Effect Sensor
- RoHS Compliant
Reviews
There are no reviews yet.