I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
ISD1820 MODULE (10 SEC)
₹400.00 Original price was: ₹400.00.₹350.00Current price is: ₹350.00. inc. GST
- Operating voltage: 2.6v to 5v
- Record and playback up to 10 sec
- Push-button and microcontroller controllable AGC circuit added tom increase audio playback volume
- Recording time: 8- 20 sec
- Built-in microphone
- On-chip 8-ohm speaker driver
- High quality, natural voice restored
- Available single-chip control audio recording control mode: the key to control or microcontroller, IO has drawn the line of control
- Can be used as propaganda module
- Auto power down mode
- Duration and sample rate can be extended to 20 sec by varying resistance
- Dimension: 43*34*11mm
ISD1820 is a single-chip voice message recording IC for single message recording and playback. It allows to record 10 sec of audio and play it back under microcontroller or by manual mode. As it consists of an inbuilt microcontroller, a message up to 10 sec long can be recorded. By connecting a resistor, these 10 secs can be extended to 20 sec. It is a non-volatile module, hence can be recorded up to 100000 times and can be stored without power. An 8-ohm speaker can be driven using the small inbuilt audio amplifier in the module.
ISD1820 chip is a resistor-controlled oscillator input (ROSC) in which sampling rate and maximum duration of audio can be controlled by placing a resistor between ROSC pin and GND, this sets oscillator frequency. The audio play volume of this module can be increased by adding AGC input to the LED output pin.

Related products
16 CHANNEL 12V RELAY
- 16 channel 12V relay board
- Operating voltage: 12V
- Supply current: 0.2 A
- Relay contact current capacity of 10A @250 V AC/10A@ 30V AC
- Optocoupler protection
- LED status indicates relay ON/OFF state.
- The 10-16 road can be any full-on/off or any road
- Common terminal(com) in each rely is user friendly and can be accessed by different signal
- Normally closed or normally open with each port
- Strong anti-jamming ability and stable performance
- The on-board power supply module doesn’t need any external power
- Dimension: 180*90*20mm
- Weight: 100gm
2 CHANNEL 5V RELAY
- High current relay
- Two LED S to indicate relays ON/OFF status
- Low-level trigger expansion board
- Opto isolation circuitry
- Works with logic level signal 3.3V or 5V devices
- Can be used as normally open (NO) or normally closed (NC)
- Back EMF protection
- Ensures diode current protection
- AC control voltage: 250v @mx10A
- DC control voltage: 30V @max 10A
- Easy installation and fixing
3.3V/5V MB102 Breadboard Power Supply Module
- Input voltage: 6.5V to 12V
- Output voltage: 3.3V to 5V
- Output current: 700Ma
- Apply to MB102 breadboard
- Sorting jumpers used to switch voltage between 3.3V and 5V
- Onboard LED indicator to show the presence of power
- Short circuit protection
- Fits securely on standard 400 and 830 points on the breadboard
- Dimensions: 53*32*23mm
- Weight: 10gm
8 CHANNEL 5V RELAY
- Relay operating voltage: 5V
- 8 channel
- High impedance controller pin
- One normally closed contact and one normally opened
- Useful for appliances control
- Power supply indicator and control indicator lamp
- Pull-down circuit to avoid malfunction
- Can control both DC and AC to 220v AC load
- Works with both 3.3 V and 5 V logic with the less current drive
- 3 terminals per SPDT relay
- Standard interface can be directly controlled by a microcontroller like Arduino, 8051, AVR, PIC, DSP, ARM, MSP430, TTL logic
- Dimension: 7*6.4*1 inch
CURRENT SENSOR ACS712 30AMPS
- Current sensor chip: ACS712ELC-30A
- Supply voltage: 4.5V to 5.5V DC
- Current range: -30A to 30A
- Sensitivity: 66 millivolt/ampere
- Low noise analogue signal path
- Output rise time: 5 micro sec
- Extremely stable output offset voltage
- Zero magnetic hysteresis
- Factory trimmed for accuracy
- Easy to interface with a microcontroller, since it outputs an analogue voltage
- Onboard power indicator
- Dimension: 7*5*5cm
- Weight: 400gm
DC POWER SUPPLY MODULE FOR DC ADAPTER PLATE
IRF520 MOSFET DRIVER MODULE SENSOR
- Operating Voltage: 3.3v & 5v
- Digital level port
- Output load voltage: 0-24v
- Output load current: <5A
- The heat sink is added for currently more than 1A
- Compatible with Arduino, MCU, ARM, Raspberry pi
- PWM dimming LED used to step-less dimming, variable-speed motor
- Output PWM can be adjusted by the original IFR520 MOS
- Arduino can drive up to 24V, such as led lights, dc motors, miniature pumps, solenoid valves etc.
- Dimension:34*30*18mm
- Size: 10gm

Reviews
There are no reviews yet.