I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
-14%
BTS7960 43A High Power Motor Driver Module/Smart Car Driver Module for Arduino Current Limit
Original price was: ₹1,500.00.₹950.00Current price is: ₹950.00. inc. GST
TL866CS USB Universal Programmer EEPROM FLASH 9 Adapters Extractor for 13000 Ics
Original price was: ₹7,525.00.₹5,000.00Current price is: ₹5,000.00. inc. GST
L9110 DC Stepper Motor Driver Board H-Bridge
Original price was: ₹350.00.₹300.00Current price is: ₹300.00. inc. GST
- Low static work current
- Power supply voltage: DC2.5-12V
- Each channel has 800mA continuous current output
- Low saturation pressure drop
- TTL/CMOS output level compatible can be connected directly to the CPU
- Output built-in clamping diode, apply to the perceptual load
- Control and drive integrated into IC
- Have pin high-pressure protection function
- Working temperature: 0-80 °C
Description
The L9110S dual-channel h-bridge motor driver module designed as a compact board used to drive small robots. This module based on the L9110 Motor Driver IC. This L9110S dual-channel H-bridge motor driver consists of two independent motor driver chips in which each capable of driving a continuous current up to 800mA. The boards operate at a voltage range from 2.5 V to 12 V enabling this module to used with both 3.3 Volts and 5 Volts microcontrollers. A set of female header pins provided to connect this module to a microcontroller. The motors easily attached via two sets of screw terminals.
The speed of the motor is controlled by a PWM Pulse Width Modulation signal and a digital output is used to change its direction. This module also used to drive a single four-line two-phase stepper motor. This module can be easily mounted onto your robot or other projects via four holes provided on the board.
Instructions:
- VCC external 2. 5V-12V voltage, GND external GND
- IA1 external MCU 10 port
- IB1 external MCU 10 port
- IA2 external MCU 10 port
- IB2 external MCU 10 port
- 0A1, 0B1 connected to 2 pins of DC motor, no direction
- 0A2, 0B2 connected to 2 pins of DC motor, no direction
- Turn on VCC, the GND module power indicator is on.
- IA1 input high level, IB1 input low level, [0A1 0B1] motor forward
- IA1 input low level, IB1 input high level, [0A1 0B1] motor reverse
- IA2 input high level, IB2 input low level, [0A2 0B2] motor forward
- IA2 input low level, IB2 input high level, [0A2 0B2] motor reverse
Reviews (0)
Shipping & Delivery
Related products
40A DC MOTOR SPEED REGULATOR PWM CONTROLLER 2000W
- Speed controller model: 40A PWM DC motor speed regulator
- Operating voltage: 10V TO 50V
- Peak current: 40A
- Control power: 0.01-2000W
- Quiescent current: 0.025A
- PWM regulation: 5-100%
- PWM frequency: 12KHz
- Operating temperature: -20 degree to 40 degree Celsius
- Stability in working
- High efficiency
- potentiometer used for speed adjustability
- Dimension: 9*5.1mm
- Weight: 95gm
48v 500W BM1418ZXF Motor Controller
- Rated Voltage: 48 Volt DC.
- Rated Power: 500W.
- Maximum Current: 30 Amps.
- Level Brake: low.
- Current limited: 30A±0.5A.
- Efficiency: ≥83%.
- Consumption: <1.5W.
- Turn The Voltage: 1-4.2V.
- Phase Angle: 120 degrees.
- Includes attachments for motor, accelerator, brake, battery, battery charging, brake light, power lock
A4988 STEPPER MOTOR DRIVE CONTROLLER BOARD
- Operating voltage supply: 8 V to 35 V
- Continuous current per phase: 1 Amp
- Maximum current per phase: 2 Amp
- Minimum logic voltage: 3V
- Maximum logic voltage: 5.5V
- Microstep resolutions: Full, 1/2, 1/4, 1/8, and 1/16
- Compact size, easy to install and use.
- All jumpers hit the ON position to indicate 16 subdivisions (4988) or 32 subdivisions (8825).
- Jm connection motor; Jv Connects 5V and 12V-24V Power Supply.
- E /S /D /G of Jc corresponds to Enable /Step /Dir /Gnd driving signal output on the connection respectively.
BTS7960 43A High Power Motor Driver Module/Smart Car Driver Module for Arduino Current Limit
- Input voltage: 6V-27V
- Maximum current: 43A
- Input level: 3.3-5V
- Control mode: PWM or level
- Duty cycle: 0-100%
- Double BTS7960 large current (43 A) H bridge driver
- 5V isolate with MCU and effectively protect MCU
- 5V power indicator on board
- Four lines from MCU to driver module (GND. 5V. PWM1. PWM2)
- Reverse the motor forward, two PWM input frequency up to 25kHZ
- Two heat flow passing through an error signal output
- Dimension: Approx. 4 * 5 * 1.2cm
Leadshine DM542
- Good high-speed performance
- Supply voltage up to +50VDC
- Output current up to 4.2A
- Pulse frequency up to 300 KHz
- Extremely cost-effective
- Automatic idle-current reduction
- 3-state current control technology
- Self-adjustment technology
- Pure-sinusoidal current control technology
- TTL compatible and optically isolated input
- 15 selectable resolutions in decimal and binary, up to 25,600 steps/rev
- Suitable for 2-phase and 4-phase motors
- DIP switch current setting with 8 different values
- Support PUL/DIR and CW/CCW modes
- Short-voltage, over-voltage, over-current protection
Leadshine DMA860E Stepper Motor Driver
- Model: DMA860E.
- Control Mode: Step & Direction.
- Max Input Frequency: 200 kHz.
- Input Voltage Range: 18 - 80 VAC / 24 - 110 VDC.
- Suggested Power Supply Voltage Range: 36-90 VDC /24-60 VAC.
- Number of DIP Switch Resolution Configurations: 16.
- 16 selectable micro-step resolutions of 400-51,200 via DIP switches.
- 8 selectable output current settings of 2.4 – 7.2A via DIP switches.
- Logic Current Range: 7-16mA (10mA typical).
- Logic Voltage Range: 4-5 VDC for pulse active high (default), or 0-0.5V for pulse active low.
- Pulse enabled at: Rising edge.
- Idle Current Percentage: 50 %.
- Number of Digital Inputs: 3.
- Step Width: 2,500 ns.
- Minimal Direction Setup Time: 5,000 ns.
- Isolation Resistance: 500M Ohm..
- Ambient Temperature: 0-50°C.
- Humidity: 40–95% RH.
- Operating Temperature: 0-70°C.
- Vibration: 5.9 m/s2 Max.
- Motor auto-identification and parameter auto-configuration for optimal torque from wide-range motors.
- Step & direction (PUL/DIR) and CW/CCW (via internal jumper set) control. Step & direction by default Multi-Stepping for smooth motor movement.
- Opto Isolation for input control signals.
- Soft-start with no “jump” when powered on.
- Protections for over-voltage and over-current.
- Dimension: 5.94 X 3.82 X 2.24 Inches.
- Weight: 1.13 lbs.
VNH2SP30 – Monster Moto Shield 30A Mini Stepper Motor Driver
- Driver Model: Monster Moto Shield VNH2SP30
- Operating Voltage: 12V to 16V DC
- Maximum current rating: 30 A
- Continuous Current: 14 A
- Number of Channels: 1
- MOSFET on-resistance: 19 m (per leg)
- Maximum PWM frequency: 20 kHz
- Current sensing available to Arduino analog pin
- Thermal Shutdown
- Under voltage and Overvoltage shutdown.
- Dimensions: 55 x 28 x 12mm
- Weight: 15gm
Reviews
There are no reviews yet.