I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
MEGA8A Atmel Microcontroller IC
₹210.00 Original price was: ₹210.00.₹178.00Current price is: ₹178.00. inc. GST
- Flash (Kbytes): 8 Kbytes
- Pin Count: 28
- Operating Freq. (MHz): 16 MHz
- CPU: 8-bit AVR
- Max I/O Pins: 23
- Ext Interrupts: 2
- SPI: 1
- UART: 1
- ADC channels: 6
- SRAM (bytes): 1024
- EEPROM (Bytes): 512
- Operating Voltage (Vcc): 2.7 to 5.5 V
- High-performance, Low-power Atmel®AVR® 8-bit Microcontroller
- Advanced RISC Architecture
- High Endurance Non-volatile Memory segments
- Power-on Reset and Programmable Brown-out Detection , Internal Calibrated RC Oscillator ,External and Internal Interrupt Sources ,Five Sleep Modes: Idle, ADC Noise Reduction, Power-save, Power-down, and Standby.
- Operating Voltages – 2.7V – 5.5V (ATmega8L) , 4.5V – 5.5V (ATmega8
The MEGA8A Atmel Microcontroller IC designed as an effectively low-power, high-performance CMOS 8-bit microcontroller. The Microchip AVR® enhanced RISC architecture was used to create this microcontroller. The Atmel AVR core has 32 general-purpose working registers and a large instruction set. All 32 registers are directly coupled to the Arithmetic Logic Unit (ALU), allowing two independent registers to be accessed in one clock cycle with a single command. As a result, the resultant design is more code efficient than traditional CISC microcontrollers, with throughputs up to 10 times quicker.
In this Atmel microcontroller, by combining a flexible 8-bit CPU with in-system programmable Flash on a monolithic chip. Thus Atmel ATMEGA128A becomes effectively powerful microcontroller. In order that it delivers a highly flexible and affordable solution to various embedded control applications. Moreover, the Atmel MEGA8515 features 8 Kbytes of In-System Programmable Flash with Read-While-Write capabilities, 512 bytes of EEPROM, 1 Kbyte of SRAM, 23 general purpose I/O lines, 32 general purpose working registers, three flexible Timer/Counters with compare modes. It also consists of internal and external interrupts, a serial programmable USART, a byte oriented Twowire Serial Interface, a 6-channel ADC (eight channels in TQFP and QFN/MLF packages) with 10-bit accuracy, a programmable Watchdog Timer with Internal Oscillator, an SPI serial port, and five software selectable power saving modes.
The CPU is turned off in Idle Mode, leaving the RAM, timers/counters, serial port, and interrupt system to continue working. The Power-down mode, on the other hand, saves the RAM data but freezes the oscillator. All other chip functions are disabled until the next external interrupt or hardware reset. It is appropriate for battery-operated applications because of these two properties. The asynchronous timer continues to operate in Power-save mode. As a result, the user may keep a timer running while the rest of the device sleeps.

Related products
120pcs 12 value 1uF-470uF Electrolytic Capacitor Kit 1UF 2.2UF 3.3UF 4.7UF 10UF 22UF 33UF 47UF 100UF 220UF
74LS540 High-Speed CMOS Logic Octal Buffer and Line Driver IC
ADXL 335 Accelerometer IC
- 3-axis sensing
- Small, low profile package
- 4 mm × 4 mm × 1.45 mm LFCSP
- Low power : 350 μA (typical)
- Single-supply operation: 1.8 V to 3.6 V
- 10,000 g shock survival
- Excellent temperature stability
- BW adjustment with a single capacitor per axis
- RoHS/WEEE lead-free compliant
- 8V- 3.6V single-supply operation
- Integrated X, Y, and Z axis accelerometer on a single chip
- X and Y axis has a 0.5Hz to 1600Hz bandwidth
- Z axis has a 0.5Hz to 550Hz bandwidth
- Hermetically sealed for temp and humidity resistance
APM/Pixhawk Power Module V6.0 Output BEC 3A XT60 Plug 28V 90A
- Input Voltage Range: 6-28V DC
- Output voltage: 5.3V ± 0.1V
- Maximum output current: 3A
- Maximum current: 90A
- Maximum voltage: 30V
- Supports from 2 cell to 6 cell battery.
- 6P cable can be directly connected to APM/Pixhawk flight control
- Additional 4P rows of pin-free to wire/PIN to connect to another flight control
- Voltage and current measurement configured for 5V ADC.
- Switching regulator outputs 5.3V and 3A max.
- Dimensions: 25mm x 21mm x 9mm
- Weight: 17gm
DC 50A 75mV Current Shunt Resistor for Amp Meter Gauge
HX711–24 Bit Analog to Digital Converter (ADC)
- It is an ADC converter with two differential input channels
- An active-low noise PGA is integrated inside the chip which provides the gain of 32, 64 and 128
- It has a power-on-reset capability which simplifies digital interface initialization.
- All controls to the IC are made through the pins. Programming is not needed.
- You can select a data rate of 10SPS or 80SPS at the output.
- Provides simultaneous supply rejection of 50Hz and 60Hz supply.
- Built-in analog power supply regulator
- The voltage supply range is from 2.6V to 5.5V
- The temperature range is from -40 °C to +85℃
IR LED Sensor
- Size: 5mm LED
- Wavelength: 940nm wavelength (most commonly used)
- Forward current (IF) is 100mA (normal condition) and 300mA (max.)
- 5A of surge forward current
- 24v to 1.4v of forward voltage
- Temperature : -40 to 100 ℃
- Soldering Temperature should not exceed 260 ℃
- Power Dissipation of 150mW at 25℃ (free-air temperature) or below
- Spectral bandwidth of 45nm
- Viewing angle: 30 to 40 degree
- High Reliability
- Excessive radiant intensity
- Having lead spacing of 2.54mm
- Easy to use with breadboard or perf board
XT60 Connector
- Manufacturer: AMASS
- Connector Series: XT60H
- Rated Voltage: DC 500V
- Metal Material: Brass Gold Plated
- Rated Current: 30A
- Momentary Current: 60A
- Number of pins: 2
- Colour: Yellow
- Contact Resistance: 0.55mΩ
- FR Level: UL94 V0
- Use Times: 1000 TIMES
- Temperature: -20℃ to 120℃
- Spatial Orientation Straight
- Compatible for Wire size up to 12AWG
- Mechanical mounting for cable
- Electrical mounting soldered
- Contact plating Gold flash

Reviews
There are no reviews yet.