I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
-14%
Pic Kit-2 Programmer
Original price was: ₹2,400.00.₹2,200.00Current price is: ₹2,200.00. inc. GST
Automatic Day Night Dusk to Dawn Light Sensor Switch LDR Control 12V 5A DC
Original price was: ₹300.00.₹250.00Current price is: ₹250.00. inc. GST
PICKIT-3 Programmer
Original price was: ₹3,500.00.₹3,000.00Current price is: ₹3,000.00. inc. GST
- Full-speed USB support using Windows standard drivers
- Real-time execution
- Processors run at maximum speeds
- Built-in over-voltage/short circuit monitor
- Low voltage to 5V (1.8 to the 5V range)
- Read/write program and data memory of the microcontroller
- Diagnostic LEDs (power, active, status)
- Read/write program and data memory of the microcontroller
- 1Erase of all memory types (EEPROM, ID, configuration, and program) with verification
- Peripheral freeze at the breakpoint.
- Program up to 512K byte flash.
Description
Microchip’s PICkitTM 3 In-Circuit Debugger/Programmer provides a low-cost hardware debugger and programmer by incorporating in-circuit debugging logic into each chip with Flash memory. The following advantages are provided by in-circuit debugging:
- Low price
- Debugging requires the least amount of additional hardware
- There is no need for expensive sockets or adapters.
The MPLAB PICkit 3 enables debugging and programming of PIC® and dsPIC® Flash microcontrollers at a low cost by utilising the MPLAB Integrated Development Environment’s powerful graphical user interface (IDE). The MPLAB PICkit 3 is connected to the design engineer’s PC via a full-speed USB interface and to the target via a Microchip debug (RJ-11) connector (compatible with MPLAB ICD 2, MPLAB ICD 3 and MPLAB REAL ICE).
Reviews (0)
Shipping & Delivery
Related products
1 CHANNEL 12V RELAY
- 1-Channel relay interface board
- Operating voltage: 12V DC
- Provide high current relay of 15A
- For quick and easy connection high-quality screw terminals provided
- Can control both AC & DC appliances
- LED status indicates relay ON/OFF state.
- High current relay of 10A @250 V AC/10A@ 30V DC
- Standard interface that can be controlled by a microcontroller (Arduino, 8051, PIC, AVR, DSP, ARM)
- For easy accessibility input signal pin connected to burg sticks
- Dimension: 43*17*17mm
- Weight: 150gm
2 CHANNEL 5V RELAY
- High current relay
- Two LED S to indicate relays ON/OFF status
- Low-level trigger expansion board
- Opto isolation circuitry
- Works with logic level signal 3.3V or 5V devices
- Can be used as normally open (NO) or normally closed (NC)
- Back EMF protection
- Ensures diode current protection
- AC control voltage: 250v @mx10A
- DC control voltage: 30V @max 10A
- Easy installation and fixing
4 CHANNEL 12V RELAY
- 4-Channel relay interface board
- Relay input voltage: 12V DC
- Relay output: 5A/250V AC
- Signal input:5V DC from the microcontroller
- High current relay of 10A @250 V AC/10A@ 30V DC
- For quick and easy connection high-quality screw terminals provided
- Can control both AC & DC appliances such as DC motors, solenoid valves, lamps, etc.
- LED status indicates relay ON/OFF state.
- Power battery terminal for relay output and aux power connection
- Standard interface that can be controlled by a microcontroller (Arduino, 8051, PIC, AVR, DSP, ARM)
- Relay can directly control all equipment’s and loads
- For easy accessibility input signal pin connected to burg sticks
- Dimension: 165*65*1mm
- Weight: 7gm
8 CHANNEL 5V RELAY
- Relay operating voltage: 5V
- 8 channel
- High impedance controller pin
- One normally closed contact and one normally opened
- Useful for appliances control
- Power supply indicator and control indicator lamp
- Pull-down circuit to avoid malfunction
- Can control both DC and AC to 220v AC load
- Works with both 3.3 V and 5 V logic with the less current drive
- 3 terminals per SPDT relay
- Standard interface can be directly controlled by a microcontroller like Arduino, 8051, AVR, PIC, DSP, ARM, MSP430, TTL logic
- Dimension: 7*6.4*1 inch
PICKIT2 Microcontroller USB Programmer PIC KIT2 Burner
- Supported Device Families: PIC10F,PIC112F, PIC16F,PIC18F,PIC24
- Programs all current 8-, 16-, and 32-bit Flash PIC microcontrollers.
- Includes the UART Tool and Logic Tool microcontroller development utilities.
- With a portable USB power source, PICkit 2 will program the downloaded code into a PIC Microcontroller
- High-quality PCB FR4 Grade with FPT Certified
USB Blaster ALTERA CPLD/FPGA Programmer
- Stably support SignalTap II embedded logic analyzer function, no mistake while crawling data.
- Fully support all Altera products such as CPLD: MAX3000, MAX7000, MAX9000, and MAXII.
- FPGA: Stratix, StratixII, StratxIII, Cyclone, CycloneII, CycloneIII, ACEX1K, APEX20K, and FLEX10K, etc.
- Active serial configuration device: EPCS1, EPCS4, EPCS16, EPCS64 etc.
- Enhanced configuration devices: EPC1, EPC4.
- Supports 3 download modes: AS, PS, and JTAG.
- Support and Nios II embedded soft core processor communication and debugging Rev.C latest version Hardware. Support jtag_uart.
- Speed is 6 times faster than parallel port download cable ByteBlasterII.
- Easy to use: MiniUSB interface, easy connection, two status indicator makes debugging more comfortable.
- Fully compatible with ALTERA USB Blaster, functionality and performance are the same as ALTERA original download cable.
- Operating Voltage: 1.5～5V JTAG IO Voltage.
- System configuration: Windows XP, Windows Vista, Windows7, USB interface.
Reviews
There are no reviews yet.