I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
-14%
Pic Kit-2 Programmer
Original price was: ₹2,400.00.₹2,200.00Current price is: ₹2,200.00. inc. GST
Automatic Day Night Dusk to Dawn Light Sensor Switch LDR Control 12V 5A DC
Original price was: ₹300.00.₹250.00Current price is: ₹250.00. inc. GST
PICKIT-3 Programmer
Original price was: ₹3,500.00.₹3,000.00Current price is: ₹3,000.00. inc. GST
- Full-speed USB support using Windows standard drivers
- Real-time execution
- Processors run at maximum speeds
- Built-in over-voltage/short circuit monitor
- Low voltage to 5V (1.8 to the 5V range)
- Read/write program and data memory of the microcontroller
- Diagnostic LEDs (power, active, status)
- Read/write program and data memory of the microcontroller
- 1Erase of all memory types (EEPROM, ID, configuration, and program) with verification
- Peripheral freeze at the breakpoint.
- Program up to 512K byte flash.
Description
Microchip’s PICkitTM 3 In-Circuit Debugger/Programmer provides a low-cost hardware debugger and programmer by incorporating in-circuit debugging logic into each chip with Flash memory. The following advantages are provided by in-circuit debugging:
- Low price
- Debugging requires the least amount of additional hardware
- There is no need for expensive sockets or adapters.
The MPLAB PICkit 3 enables debugging and programming of PIC® and dsPIC® Flash microcontrollers at a low cost by utilising the MPLAB Integrated Development Environment’s powerful graphical user interface (IDE). The MPLAB PICkit 3 is connected to the design engineer’s PC via a full-speed USB interface and to the target via a Microchip debug (RJ-11) connector (compatible with MPLAB ICD 2, MPLAB ICD 3 and MPLAB REAL ICE).
Reviews (0)
Shipping & Delivery
Related products
1 CHANNEL 12V RELAY
- 1-Channel relay interface board
- Operating voltage: 12V DC
- Provide high current relay of 15A
- For quick and easy connection high-quality screw terminals provided
- Can control both AC & DC appliances
- LED status indicates relay ON/OFF state.
- High current relay of 10A @250 V AC/10A@ 30V DC
- Standard interface that can be controlled by a microcontroller (Arduino, 8051, PIC, AVR, DSP, ARM)
- For easy accessibility input signal pin connected to burg sticks
- Dimension: 43*17*17mm
- Weight: 150gm
16 CHANNEL 5V RELAY
- 16 channel 5V relay board
- Operating voltage: 5V
- Supply current: 500mA
- Relay contact current capacity of 10A @250 V AC/10A@ 30V AC
- Optocoupler protection
- Low state voltage: 0V to 0.5V (relay is ON)
- High state voltage: 3.7V to 5V(relay is OFF)
- Single-chip design with reliable performance
- Strong anti-interferences
- Strong anti-jamming ability and stable performance
- The on-board power supply module doesn’t need any external power
- Common terminal(com) in each rely is user friendly and can be accessed by different signal
- Dimension: 180*90*20mm
- Weight: 100gm
4 CHANNEL 12V RELAY
- 4-Channel relay interface board
- Relay input voltage: 12V DC
- Relay output: 5A/250V AC
- Signal input:5V DC from the microcontroller
- High current relay of 10A @250 V AC/10A@ 30V DC
- For quick and easy connection high-quality screw terminals provided
- Can control both AC & DC appliances such as DC motors, solenoid valves, lamps, etc.
- LED status indicates relay ON/OFF state.
- Power battery terminal for relay output and aux power connection
- Standard interface that can be controlled by a microcontroller (Arduino, 8051, PIC, AVR, DSP, ARM)
- Relay can directly control all equipment’s and loads
- For easy accessibility input signal pin connected to burg sticks
- Dimension: 165*65*1mm
- Weight: 7gm
89C2051 Atmel Microcontroller IC
- Core Processor: 8051
- Data Bus Width: 8 bit
- Maximum Clock Frequency: 24 MHz
- Program Memory Size: 2 KB
- Program Memory Type: Flash
- Supply Voltage Range: 4 V to 6 V
- Package: PDIP-20
- Compatible with MCS-51™ Products
- 2K Bytes of Reprogrammable Flash Memory – Endurance: 1,000 Write/Erase Cycles
- 7V to 6V Operating Range
- Fully Static Operation: 0 Hz to 24 MHz
- Two-level Program Memory Lock
- 128 x 8-bit Internal RAM
- 15 Programmable I/O Lines
- Two 16-bit Timer/Counters
- Six Interrupt Sources
- Programmable Serial UART Channel
- Direct LED Drive Outputs
- On-chip Analog Comparator
- Low-power Idle and Power-down Modes
USB TO RS-485 CONVERTER
- Small and compact size
- Baud rate:75 bps-115200bps, up to 6Mbps
- Communication distance:1200m
- Support USB 2.0 standard
- Self-powered by USB bus
- Working temperature:-40degree - +85 degree
- RS-232 serial port transmission speed of max 115.2Kbps
- Supports full handshake protocol, full-duplex data operating mode
- Directional control: Uses automatic data flow control technology, automatic identification and control of data transfer direction Load capacity: support multipoint
- Interface protection: TVS tube protection, USB self-recovery protection
- Screw Terminal Connector for easy connection
- The module requires no external power, it takes power from the USB port
- Supported Systems: Windows XP, Vista, Windows 7, Linux, macOS, and
- Dimension:6.1x1.6x1.3cm
USB TO SERIAL CP2102 CONVERTER
- Reliable and stable device
- Baud rate:300bps-1Mbps
- Supports Windows, Linux &Mac
- Compliant withUSB2.0 at a full-speed 12Mbps
- Self-power :3.0 to 3.6v
- USB bus power:4.0 to 5.25v
- Supports all handshaking and modem interface signal
- Standard USB type A male and TTL 6pin connector.
- 6pins for 3.3V, RST, TXD, RXD, GND & 5V.
- All handshaking and modem interface signals.
- Byte receives buffer; 640 bytes transmit buffer.
- Hardware or X-On/X-Off handshaking supported.
- Event character support Line break transmission.
- USB suspend states supported via SUSPEND pins.
- Temperature Range: -40 to +85.
- Dimension: 42mm X 15mm.
Reviews
There are no reviews yet.