I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
ESP8266 ESP-12F
Original price was: ₹250.00.₹200.00Current price is: ₹200.00. inc. GST
ESP8266 ESP - 03 WIFI Transreceiver Wireless Module
₹800.00 inc. GST
TB6560 4 Axis Stepper Motor Driver
- Driver Chip: TB6560AHQ
- Operating Voltage: 10-35V
- Nominal Voltage: 24V
- Stepper motor drive current: 1.5A – 3A/phase
- With the large heat sink to ensure good heat dissipation
- Double-pole constant flow PWM actuation output
- 6N137 high-speed OptoCoupler, to ensure a high speed without stepping out.
- Compatible Stepper motors: 2/4 Phase, 4/6/8 leads stepper motors within 3.5A
- 1 – 1/16 micro step setting – higher accuracy, smoother operation
- Full closed-type optical isolation to protect the user’s computer and equipment
- Professional design, two-stage signal processing, super anti-jamming
- Bipolar constant current chopper drive motor low-speed non-creeping phenomenon, noise, non-resonant region
- Four input control
-
Description
This stepper motor driver controller board used an updated version of the TB6560 Chip. It is a high-performance micro-stepping drive based on pure-sinusoidal current control technology. This pure sine and the self-adjustment technology to self-adjust current control parameters offers a quick setup while using different motors. Thus This CNC Router Single Axis 3.5A Stepper Motor driver board can run with smaller noise, lower heating, smoother movement and have better performances at a higher speed than most of the drives in the markets. It is suitable for driving 2-phase and 4-phase hybrid stepping motors. Therefore, in order to improve reliability, the driver features some built-in protection functions. Such as low voltage shutdown, overheating stop, and overcurrent protection circuit.
- The inductive DC-DC step-down module, computer terminal and then using the power isolation module design, just to run a set of power input, the input voltage of 24V-40V allows high voltage input, completely beyond TB6560, TB6560 of the input voltage. typically 24V.
- .Increase the external signal input optocoupler used in all-optical coupling isolation input.
- Increase the simulation 0-10V output, combined with MACH3 software to control the drive spindle speed.
- add a select group of relay outputs (can output two relays, control the two different devices, load isolation, P9 pin relay 1, relay 2 pin P16, P17 cited relay 3 setting foot)
- Increase the 20-pin multi-connector, docking variety of signal input control. you can use the microcontroller, ARM, DSP control.
- Add the buffer chip signal, amplify the external signal, increasing the accuracy of the pulse.
- E-type bottom oversized aluminium heat sink to ensure the full capacity 24 hours. The temperature is very low (which can add a fan or other cooling device).
Reviews (0)
Shipping & Delivery
Related products
5V Stepper Motor 28BYJ-48 with ULN2003
- Rated voltage: 5V DC
- Reduction Ratio: 64:1
- Step Angle: 5.625° /64
- Frequency: 100Hz
- Self-positioning Torque: >34.3mN.m
- No of phase: 4
- Speed variation ratio: 1/64
- Pull-in torque: 300 gf.cm
- Friction torque: 600-1200 gf.cm
- DC resistance: 50Ω±7% (25°C)
- Insulated resistance: >10MΩ (500V)
- Insulated power: 600VAC/1mA/1s
- Rise in Temperature <40K(120Hz
- Noise <35dB(120Hz,No load,10cm
- Stepper motor with a standard interface, when used directly pluggable.
- Four-phase LED indicator which indicates the status of the stepper motor work.
- Compact size stepper motor perfect for small robotics applications.
A3967 STEPPER MOTOR DRIVER
- A3967 precision micro-stepping driver
- Power supply: 7v to 30v
- Logic voltage: 5v to 3.3v
- Higher the voltage higher the torque at high speed
- Adjustable current control from 150Ma/ phase to 750ma phase
- Automatic current decay mode detection/selection
- Fast, slow, and mixed current decay modes
- Internal UVLO and thermal shutdown circuitry
- Crossover current protection
- Micro stepping resolution to full, half, quarter, and eighth steps by broken out MS1 and MS2 pins.
- Compatible with Arduino, GRBL G-Code interpreter for driving3-axis CNC machines
- Salington sink drivers used
- Compactible with 4, 6,8 wire stepper motor of any voltage
Leadshine DM542
- Good high-speed performance
- Supply voltage up to +50VDC
- Output current up to 4.2A
- Pulse frequency up to 300 KHz
- Extremely cost-effective
- Automatic idle-current reduction
- 3-state current control technology
- Self-adjustment technology
- Pure-sinusoidal current control technology
- TTL compatible and optically isolated input
- 15 selectable resolutions in decimal and binary, up to 25,600 steps/rev
- Suitable for 2-phase and 4-phase motors
- DIP switch current setting with 8 different values
- Support PUL/DIR and CW/CCW modes
- Short-voltage, over-voltage, over-current protection
NEMA 23 10.1 kg-cm
- Operating Voltage : 2.3 Volts
- Step Angle : 1.8°
- Holding Torque : 10.1 kg-cm
- Supply Current (A) : 2.8 Ampere/Phase
- Number of Leads : 4
- Inductance : 2.2 mH/Phase
- Resistance : 0.83 Ohm
- Rotor Inertia : 275 gm-cm2
- Weight (gm) : 650
- Detent Torque (kg-cm) : 0.36
- Frame Size (mm) : 57 x 57
- Inductance Accuracy : ±20%
- Resistance Accuracy : ±10%
- Shaft Diameter (mm) : 6.35
- Shaft Length (mm) : 20.6
- Step Angle Accuracy : ±5%
- Comparably more powerful than NEMA17 motors.
- The input pulse decides the rotation angle of the motor.
- High accuracy of around 3 to 5% a step.
- It provides good starting, stopping, and reversing.
- Control of this motor is less costly because of the exclusion of complex control circuitry.
- The speed is proportional to the frequency of the input pulses.
TB6560 4 Axis Cnc Controller 4 Axis Stepper Motor Driver DSP Controlled 3.5A 24V
- Rated maximum output: ± 4.5A, 40V, Peak 5A, low output impedance, source 0.5?,
- the receiving end of 0.4?, low voltage shutdown, thermal parking and circulation.
- circuit protection. After I design, you can set the current output of 0.5A 1A 1.8A 2.5A.
- 3.3A 4A 4.5A to accommodate more and different motor Current.
- The drive is suitable software mach2, mach3, (mach3 have support WIN7 system), KCAM4 like.
TB6560 Driver Board 3A CNC Router Single 1 Axis Controller Stepper Motor
- Supply voltage up to +32 VDC
- Output current up to 3.0A
- Pulse frequency up to 20 KHz
- Suitable for 2-phase and 4-phase motors
- Over-voltage and short-circuit protection
- 7 output current choices, max 3200 steps/rev
- Automatic idle-current reduction
- Single-chip motor driver for sinusoidal micro-step control of stepping motors
- High output withstands voltage due to the use of BiCD process:
- Forward and reverse rotation
- Selectable phase excitation modes (2, 1-2, 2W1-2, and 4W1-2)
- High output withstand voltage: VDSS = 40 V
- High output current: IOUT = TB6560AHQ: 3.5 A (peak)
- Internal pull-down resistors on inputs: 100 kΩ
- Output monitor pin: MO current (IMO (max) = 1 mA)
- Reset and enable pins
XB NEMA 34 (86mm-S) Coupling 12.7x8mm
- Material: Aluminum alloy hubs and elastomeric polyurethane spider.
- Product Type: Clamp-style jaw coupling without keyway.
- Large Bore Diameter: 12.7mm
- Small bore diameter:8mm
- Number of Screws: 2 each.
- Angular Misalignment: +/-1°.
- Parallel Misalignment: +0.20mm/-0.20mm .
- Maximum Rotational Speed: 6500RPM.
- Suitable for Nema 23 Stepper Motor or for any motor/rod having an 12.75mm diameter
- Widely used in motors, stepper motors, encoders, and servo machines
Reviews
There are no reviews yet.