I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
-14%
TL866CS USB Universal Programmer EEPROM FLASH 9 Adapters Extractor for 13000 Ics
Original price was: ₹7,525.00.₹5,000.00Current price is: ₹5,000.00. inc. GST
ULink2 ARM Emulator Programmer firmware Support MDK5.0 Cortex-M4 SWD
Original price was: ₹3,000.00.₹2,800.00Current price is: ₹2,800.00. inc. GST
USB AVR ISP 10 Pin Programmer | ATmega8 USB Programmer
Original price was: ₹350.00.₹300.00Current price is: ₹300.00. inc. GST
- Allows you to read or write the microcontroller EEPROM, firmware, fuse bits and lock bits
- Support for Linux, Mac OS X and Windows XP,7,8
- 5 KB/sec maximum write speed
- Software controlled SCK option to support targets with low clock speed (< 1.5MHz)
- 10 pin ISP interface
- Works under multiple platforms. Linux, Mac OS X and Windows are tested.
- Software controlled SCK option to support targets with low clock speed (less than 1.5MHz).
- 6 Pin Adapter board along with the programmer for Standard ISP connections.
- B-type USB Connector for power.
- Separate Two Different leds for power & programmer status.
Description
This USBasp is an in-circuit serial electronic programmer designed for the Atmel AVR Microcontroller family. USBasp is a low-cost programmer that converts hex file (.hex) into an AVR microcontroller which consist of an Atmega8 microcontroller and a couple of passive components with a 12 MHz operating frequency of ATMega8. No special USB controller is required since the programmer uses a firmware-only USB driver.
In order to program a microcontroller we need to access four pins of the microcontroller, but our USB will have only two pins for communication, so how can we program a microcontroller with a USB. Here comes the functioning of the USB ASP Programmer. In short, a USBasp in-circuit serial programming adapter is used to install bootloaders and firmware on common AVR microcontrollers. In USBasp Target referred to as the board, we are programming. This module features an SCK option to support Targets with a low clock speed of less than 1.5MHz.
USBasp programmer with a 10-pin ISP connection provides the interface to the microcontroller at a programming speed of 5KB/sec. This USB interface is achieved by using an Atmega 8 processor and the rest is done in firmware. A 10-pin male header is used for various ISP header pins to make the interfacing easier. These are modules of compact size but with elegant design. This USB AVR programmer can be powered by an external power supply (target board) or from the USB Port Autospeed control function for flashing devices to get the best performance/stability.
The USBasp programmer will work with a wide variety of Atmel AVR microcontrollers including the Atmega8a and Atmega168a. The USBasp driver will work on both 32 and 64-bit platforms. As a result, a USBASP programmer works on multiple platforms such as Windows, Mac OS X, and Linux.
Free Comparable Boot Loaders:
- AVR SinaProg for Windows.
- AVRDUDE supports USBasp since version 5.2.
- BASCOM-AVR supports USBasp since version 1.11.9.6.
- Khazama AVR Programmer – An AVRdude GUI for MS Windows.
- eXtreme Burner – AVR is a Windows GUI Software for USBasp based USB AVR programmers.
- AVR Loader.
Reviews (0)
Shipping & Delivery
Related products
CH341A 24 25 Series EEPROM Flash BIOS USB Programmer with Software & Driver
- USB interface
- With CH341A chip
- Support 24 EEPROM and 25 SPI flash 8pin or 16pin chip
- With 24/25 status indicator lamp
- Support USB to TTL conversion
- Support 24EEPROM and 25 SPI flash 8pin/ 16pin chip
- Recognize 25 series chip automatically
- Supports download STC series procedure of single chip
- SPI pin to support expanding the utility
- STC microcontroller supports a full range of program download
- Support expanding the utility by SPI pin
- With SOP8 SOP16 to DIP8 converter board
- Used in wide applications – PC motherboard, LCD monitor, DVD, router program reading and writing
- Supports Windows XP, Vista, Win7 and Win8 (32/64bit) system
- Provide 5V-3.3V power supply output
FlySky 2.4Ghz 6CH Receiver
- Item Name: FS-R6B Receiver
- Brand Name: Flysky
- Power input: 4.0 -6.5 V DC
- RF power: less than 20DBm
- Modulation: GFSK
- Code type: PCM
- Sensitivity: 1024
- PWM channels: 6
- Protocol: AFHDS
- Distance: >150m
- Antenna type: Built-in antenna
- Low voltage warning: LED
- Charger port
- Certificate: CE,FCC,RoHS
- Dimension: 30*25*8mm
- Weight: 25g
MAX3232 RS232 TO TTL CONVERTER
- Chip model: MAX3232 IC
- Supply voltage: 3V -5V
- Maximum Baud Rate: up to 120kbps
- High speed, replaceable MAX232 based.
- Working mode: Full duplex
- Supports microcontroller UARTs – 5V TTL signal levels.
- Low current status LED(s)
- Very low power consumption
- Optional onboard PSU for internal/external use for a quick start out of the box.
- Power can be routed to pin 9 (if required) on the RS232 connector – useful for specific
- Operating temperature: -40 degree to +85 degree Celsius
- Dimension: 16.22*10.3*3.5mm
- Weight: 1gm
Mini St-Link V2 Stlink Emulator Downloader Stm8 Stm32 with Metal Shell
- Support the full range of STM32 SWD interface debugging, simple interface (including power supply), 4 line speed, stable work; Interface definition shell directly address
- Support all series STM8 SWIM download debugging (common development environment such as IAR, STVD, etc.) are supported.
- Support the firmware upgrade automatically, to ensure that the ST company product support. When they leave the firmware has been upgraded to the latest V2. The J17. S4.
- Increase the 5 v power output, the output it can protect the I/O port, not afraid of error cause damage of ST-LINK V2.
- Easy interface to use pure copper plating 2.54 spacing horn, with 20 cm Dupont line, can deal with different target board line sequence, flexible connection;
- Use U disk aluminium alloy shell to protect the mainboard, convenient to carry, not afraid of static electricity, not afraid of tumbling.
- Material: metal + plastic
- Colour: Black/Red/Green/Pink/Gold/Grey/Blue/White( Randomly Sent )
- Power output: 5V
- simulator: about 5.6*2*0.8cm
- Debugging line: about 20cm
- Weight (kg): 0.012
Pic Kit-2 Programmer
- Supported Device Families: PIC10F,PIC112F, PIC16F,PIC18F,PIC24
- Programs all current 8-, 16-, and 32-bit Flash PIC microcontrollers.
- Includes the UART Tool and Logic Tool microcontroller development utilities.
- With a portable USB power source, PICkit 2 will program the downloaded code into a PIC Microcontroller
- High-quality PCB FR4 Grade with FPT Certified
PICKIT-3 Programmer
- Full-speed USB support using Windows standard drivers
- Real-time execution
- Processors run at maximum speeds
- Built-in over-voltage/short circuit monitor
- Low voltage to 5V (1.8 to the 5V range)
- Read/write program and data memory of the microcontroller
- Diagnostic LEDs (power, active, status)
- Read/write program and data memory of the microcontroller
- 1Erase of all memory types (EEPROM, ID, configuration, and program) with verification
- Peripheral freeze at the breakpoint.
- Program up to 512K byte flash.
USB Blaster ALTERA CPLD/FPGA Programmer
- Stably support SignalTap II embedded logic analyzer function, no mistake while crawling data.
- Fully support all Altera products such as CPLD: MAX3000, MAX7000, MAX9000, and MAXII.
- FPGA: Stratix, StratixII, StratxIII, Cyclone, CycloneII, CycloneIII, ACEX1K, APEX20K, and FLEX10K, etc.
- Active serial configuration device: EPCS1, EPCS4, EPCS16, EPCS64 etc.
- Enhanced configuration devices: EPC1, EPC4.
- Supports 3 download modes: AS, PS, and JTAG.
- Support and Nios II embedded soft core processor communication and debugging Rev.C latest version Hardware. Support jtag_uart.
- Speed is 6 times faster than parallel port download cable ByteBlasterII.
- Easy to use: MiniUSB interface, easy connection, two status indicator makes debugging more comfortable.
- Fully compatible with ALTERA USB Blaster, functionality and performance are the same as ALTERA original download cable.
- Operating Voltage: 1.5～5V JTAG IO Voltage.
- System configuration: Windows XP, Windows Vista, Windows7, USB interface.
Reviews
There are no reviews yet.