I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
CC3D flight Control
₹1,799.00 Original price was: ₹1,799.00.₹1,749.00Current price is: ₹1,749.00. inc. GST
- Powerful STM32 32-bit microcontroller running at 90 MIPS with 128KB Flash and 20KB RAM.
- 3-axis high-performance MEMs gyros and 3-axis high-performance MEMs accelerometer.
- Tiny 36 x 36 mm 4 layer PCB for superior electrical noise reduction and flight performance.
- Software support for Windows, Mac, and Linux.
- Supported by powerful OpenPilot GCS
- 10 PWM outputs to servos or ESC’s, or for camera stabilization
- Direct high-speed USB support with no drivers required, a true plug and play device.
- Spectrum satellite receiver support.
- Futaba S-BUS hardware support.
- With a function of being directly plugged into the satellite receiver
- 10 PWM outputs to servos or ESC’s, or for camera stabilization
- Innovative Flexi-port technology for superior port flexibility.
- 4Mbits on-board EEPROM for configuration storage.
Out of stock
The CC3D flight control board is a powerful and affordable, all-in-one stabilization hardware flight controller, based on OpenPilot firmware. Using the OpenPilot Ground Control Station (GCS) software, CC3D is configured to fly any airframe from fixed-wing to an octocopter. The CC3D is an updated version of the original Copter Control board. The only difference is using the powerful single-chip IMU. The CC3D board’s design consists of an improved gyro sensor which is less affected by temperature changes. Apart from the gyro sensor change, it is identical to the original Copter Control.
The Copter Control platform is designed to perform a host of functions on multi-copter, fixed-wing UAVs, and even Flybarless Helicopter support with auto level. The new version included Flexiport provides either I2C connectivity or a second serial port. CC3D boards also feature that you can add a GPS module, even waypoint based flight. Â Thus this OpenPilot CC3D is referred to as the most popular flight controller used for FPV Racing. They have a wide range of applications in many high-end FPV racers such as the Lumenier QAV 250 and the TBS Gemini.
This OpenPilot CC3D EVO Flight Controller Side Pin card is directly compatible with satellite receivers without the need for any additional cables. It also has a powerful STM32 32-bit microcontroller running at 90MIPs with 128KB Flash and 20KB RAM. The 3-axis high-performance MEMs technology is used for both gyro and accelerometer. The card can be programmed in Windows, Mac, or Linux with USB and OpenPilot software. This eliminates the need for any drivers to install.

Related products
30AMPS ESC DYS
- Input Voltage: 11.1 ~ 11.7 V.
- Constant Current: 30A (Max 40A<10s).
- BEC: 5V/3A.
- Li-Po battery: 2S ~ 3S.
- Ni-MH 4-10 CELLS Auto Detect.
- Separately voltage regulator IC for the microprocessor, providing good anti-jamming capability.
- Used with SimonK updated firmware for Multicopter
- Battery side – Male deans (T) connector.
- Motor side – Female 3.5mm gold connector.
- 30A ESC for BLDC has onboard BEC.
- Developed specifically for multi-rotor use
- Smooth, linear, and precise throttle response
- Extreme low output resistance, super current endurance
- Auto Low Battery Slow down at 3.0V/cell Lipo, cut-off at 2.9V/cell lipo.
- Supported motor speed (Maximum): 210000 RPM (2 poles), 70000 RPM (6 poles), 35000 RPM (12 poles).
- Dimension: 46* 26 * 11mm
- Weight: 23g
6045(6×4.5) Propeller
- Length: 6″.
- Pitch: 4.5″.
- Shaft Diameter: 5mm.
- Total length: 6 inch / 150 mm.
- Material: Glass Fiber Nylon
- It includes a set of plastic reducers(3, 4, 5, 6 mm)
- Durable plastic construction provides both lightness and rigidity.
- Â 6045(6X4.5) Glass Fiber Nylon Propeller comes Epoxy resin cover.
- Very strong and lightweight.
- Quick to release, quick to attach
- New design propellers, with greater aerodynamic efficiency, good lifting capacity.
- Dimensions: 30 x 6 x 4 cm
- Weight: 26 gm.
APM/Pixhawk Power Module V6.0 Output BEC 3A XT60 Plug 28V 90A
- Input Voltage Range: 6-28V DC
- Output voltage: 5.3V ± 0.1V
- Maximum output current: 3A
- Maximum current: 90A
- Maximum voltage: 30V
- Supports from 2 cell to 6 cell battery.
- 6P cable can be directly connected to APM/Pixhawk flight control
- Additional 4P rows of pin-free to wire/PIN to connect to another flight control
- Voltage and current measurement configured for 5V ADC.
- Switching regulator outputs 5.3V and 3A max.
- Dimensions: 25mm x 21mm x 9mm
- Weight: 17gm
Ardupilot Mega APM 2.8 Flight Controller
- Model: APM 2.8
- Input Voltage (V): 12-16 V.
- Processor: ATMEGA2560 and ATMEGA32U-2
- Micro SD card slot: No.
- Arduino Compatible
- MPU6000 : 3-Axis MEMS Gyroscope + accelerometer
- High-performance Barometer upgraded to MS5611-01BA03, from Measurement Specialties.
- Support hundreds of 3D waypoints
- Full mission scripting with point-and-click desktop utilities
- Two-way telemetry and in-flight command using the powerful MAVLink protocol
- Powerful Ground Control Software
- Supports full "hardware-in-the-loop" simulation with Xplane and Flight Gear
- On-board 4 Megabyte Data flash chip for automatic data logging.
- Optional off-board GPS, an uBlox LEA-6H module with Compass.
- Dimensions: 70 x 45 x 15mm
- Weight: 70gm
F550 HEXACOPTER FRAME
- Model: F550
- Material: Glass Fiber + Polyamide-Nylon
- Wheelbase: 550mm
- Arm Size : 220 x 40mm
- Motor Mounting Hole Diameter: 3mm
- Landing Gear Material: ABS Plastic
- Landing Gear Height (mm): 200
- Landing Gear Color: Black
- Landing Gear Weight: 75gm
- Comes with Black, Red, and White arms for easy orientation during flying
- Plastic injection molding ensures hardness and lighter weight
- Built from high-quality glass fiber and nylon
- Easy to build and assemble
- Made by advanced engineering material, super strong & smooth
- Easy to assemble and disassemble.
- The frame is tough and durable.
- The arm equips support ridges for better and faster forward flight.
- In-built power distribution board.
- Large Center plate allows mounting of gimbals and camera for FPV and aerial photography
- Weight:624gm
Flysky FS-TH9X 9Channel With FS-R8B
- Transmitter: FS-TH9X Upgrade with FS-RM003 2.4GHz Module
- Receiver: FS-R8B
- Default Mode: Mode-2
- Input Power: 12V DC (1.5V x 8 AAA Battery)
- Bidirectional System
- Frequencies-Hopping
- Omni-directional High Gain Antenna
- Low Power Consumption
- Colour: Black
- Charger Port: Yes(DC Port)
- Data Output: PPM
- Channel Resolution: 4096
- Channel Delay: Better than 30us
- Display: STN VA-73 39mm LCD
- DSC port: 3.5mm:output:PPM
- Dimension:185*220*110mm
- weight: 690gm
KK-Mini FLIGHT CONTROLLER
- IC:Â Atmega644 PA
- Gyro/Accelerometer: Auto-level:Â Yes
- Input Voltage:Â 4.8-6.0V
- AVR interface: standard 6 pins.
- The signal from Receiver: 1520us (5 channels)
- Signal to ESC: 1520us
- LCD size: 24*18mm
- Mini buttons size: Four 3.3*4.2mm
- Mounting holes: 30.5x30.5mm
- Voltage sensor:Â One red positive pin header for.
- Input rail:Â Single row 2.54mm pitch pin header for input signal
- Firmware Version: 1.6
- Dimension: 36x36x11.5mm

Reviews
There are no reviews yet.