GY-88 10 Axis HMC5883L MPU6050 BMP085 IMU Module for Arduino
- MPU 6050 Motion Sensor module: 3-axis gyroscope, 3-axis accelerometer
- HMC5883L module：three-axis magnetic field module
- BMP085 barometer pressure sensor
- Chip: MPU-6050
- Power supply: 3v-5V power
- gyroscope range: + 250 500 1000 2000 °/ s
- Acceleration range: ± 2 ± 4 ± 8 ± 16 g
- HMC5883L range: ± 1.3-8 Gauss
GY-906 MLX90614ESF Contactless Temperature Sensor Module
- Small size, low cost
- Mounted on a breakout board with two types of pins
- 10k Pull up resistors for the I2C interface with optional solder jumpers
- Easy to integrate
- Factory calibrated in wide temperature range:
- Sensor temperature: -40...+125°C
- Object temperature: -70...+380°C
- High accuracy of 0.5°C over the wide temperature range
- (0...+50°C for both Ta and To) High (medical) accuracy calibration
- The measurement resolution of 0.02°C
- Single and dual-zone versions
- SMBus compatible digital interface
- Customizable PWM output for continuousreading
- Simple adaptation for 8...16V applications
- Sleep mode for reduced power consumption
GY-906-BCC MLX90614ESF-BCC IR TEMPERATURE MODULE
- Input supply: 3V-5V
- Input current: 2mA
- Small size, low cost.
- Mounted on a breakout board with two types of pins.
- 10k pull up resistors for the I2C interface with optional solder jumpers.
- Easy to integrate
- Factory calibrated in a wide temperature range
- Mounted on a breakout board with two types of pins
- -40 degrees to 125 degrees C for sensor temperature
- -70 degrees to 380 degrees C for object temperature.
- High accuracy of 0.5C over a wide temperature range
- The measurement resolution of 0.02C
- Single and dual-zone versions
- SMBus compatible digital interface
- Customizable PWM output for continuous reading
- Simple adaptation for 8v to 16V applications
- Sleep mode for reduced power consumption
- Different package options for applications and measurements versatility
GY-9250 sensor module
GY-9960 APDS-9960 RGB and Gesture Sensor module
GY-BME280 ALTIMETER ATMOSPHERIC PRESSURE 12C
HB100 Microwave Doppler Radar Motion Sensor module
HB100 Microwave Doppler Radar Wireless Motion Sensor Module
HC-05 Bluetooth Bee Master BEE05
- Power supply: 3.3V
- A power supply of more than 3.3V will destroy the module.
- Paring user’s name: HC-05
- Default baud rate: 38400
- Default slave model
- Default pairing password: 1234
- This module was designed for XBEE so it’s compatible with the XBEE expansion base. This module was designed for XBEE so it’s compatible with the XBEE expansion base.
- It can be used for an MCU system whose voltage is 3.3V.
- Users can set master-slave model, baud rate, paring password, and user’s information by AT command.
- Bluetooth adapter pairs with Bluetooth Bee salve device.
- With an efficient onboard antenna, the exposed antenna qualifies the transmit signal and makes it farther.
- Dimension: : 3.3 x 2.5 x 0.9 cm
- Weight: 5g
HC-05 Bluetooth Module
- Bluetooth serial port Profile
- Bluetooth protocol: Bluetooth Specification v2.0+EDR
- Frequency: 2.4GHz ISM band
- Operating Voltage: 4V to 6V (Typically +5V)
- Operating Current: 30mA
- Modulation: GFSK(Gaussian Frequency Shift Keying)
- Emission power: ≤4dBm, Class 2
- Sensitivity: ≤-84dBm at 0.1% BER
- Speed: Asynchronous: 2.1Mbps(Max) / 160 kbps, Synchronous: 1Mbps/1Mbps
- Working temperature: -20 ~ +75Centigrade
- Serial Bluetooth module for Arduino and other microcontrollers
- Range: <100m
- Works with Serial communication (USART) and TTL compatible
- Follows IEEE 802.15.1 standardized protocol
- Uses Frequency-Hopping Spread Spectrum (FHSS)
- Can operate in Master, Slave or Master/Slave mode
- Can be easily interfaced with Laptop or Mobile phones with Bluetooth
- Supported baud rate: 9600,19200,38400,57600,115200,230400,460800.
- Dimension: 26.9mm x 13mm x 2.2 mm
HC-05 Bluetooth Shield for Arduino
- Bluetooth serial port Profile
- Bluetooth protocol: Bluetooth Specification v2.0+EDR
- Frequency: 2.4GHz ISM band
- Communication Range: 10M
- Serial Bluetooth module for Arduino
- Can operate in Master, Slave or Master/Slave mode
- UART interface (TTL) with programmable baud rate (SPP firmware installed)
- Default baud rate: 38400(CMD MODE) / 9600(DATA MODE), data bits: 8, stop bit: 1, Parity: No parity
- Onboard PCB antenna
- FCC ID certificated
