AC-DC Power Module HLK-PM03 230V to 3.3V /3W
- Meet UL, CE requirements
- Rated input voltage: AC 100V -230V
- Input voltage range: 90V -264V AC
- Maximum input current: <0.2A
- Input current surge: <10A
- Maximum input voltage: <270V AC
- Input Low Voltage Efficiency Vin=110V AC，Output full-load≥ 69%
- Input High Voltage Efficiency Vin=220V AC，output full-load≥ 70 %
- Long-term reliability
- Voltage Regulation: ±0.2%
- Load Regulation: ±0.5%
- Ultra-thin and small module
- High efficiency, high power density
- Low ripple and low noise
- Output overload and short circuit protection
- Working temperature: – 20 degrees to +60 degrees Celsius
- Storage temperature: -40 degrees to 80 degrees Celsius
- Relative humidity: 5-95%
- Cooling way: Natural cooling
- Atmospheric pressure: 80-106Kpa
- Weight: 21g
- Size: 38x23x18mm
AC-DC Power Module HLK-PM12 230V to 12V /3W
- Rated input voltage: AC 100V -230V
- Input voltage range: 90V -264V AC
- Maximum input current: <0.2A
- Input current surge: <10A
- Maximum input voltage: <270V AC
- Input Low Voltage Efficiency Vin=110V AC，Output full-load≥ 69%
- Input High Voltage Efficiency Vin=220V AC，output full-load≥ 70 %
- Short-term maximum output current: ≥1000 mA
- Long-term reliability
- Voltage Regulation: ±0.2%
- Load Regulation: ±0.5%
- Ultra-thin and small module
- High efficiency, high power density
- Low ripple and low noise
- Output overload and short circuit protection
- Working temperature: – 20 degrees to +60 degrees Celsius
- Storage temperature: -40 degrees to 80 degrees Celsius
- Relative humidity: 5-95%
- Cooling way: Natural cooling
- Atmospheric pressure: 80-106Kpa
- Weight: 21g
- Size: 38x23x18mm
ISD1820 MODULE (10 SEC)
- Operating voltage: 2.6v to 5v
- Record and playback up to 10 sec
- Push-button and microcontroller controllable AGC circuit added tom increase audio playback volume
- Recording time: 8- 20 sec
- Built-in microphone
- On-chip 8-ohm speaker driver
- High quality, natural voice restored
- Available single-chip control audio recording control mode: the key to control or microcontroller, IO has drawn the line of control
- Can be used as propaganda module
- Auto power down mode
- Duration and sample rate can be extended to 20 sec by varying resistance
- Dimension: 43*34*11mm
TTP229 16WAY
- On-board TTP229 capacitive touch sensor IC
- Operating voltage 2.4V~5.5V.
- Built-in regulator with external enable / disable option.
- Operating current, @VDD=3V no load.
- At low power mode typical 2.5uA.
- At fast mode typical 9.0uA; @VDD=3V.
- The response time is about 100mS at fast mode, 200mS at low power mode
- Built-in regulator
- Adjustable sensitivity
- Two modes
- Simple 8 key mode with independent 8 Channel parallel output.
- Advanced 16 Key modes with I2C interface output.
- Provides Fast mode and Low Power mode selection by pad option (LPMB pin).
- Provides direct mode or toggle mode CMOS output or open-drain output.
- Auto calibration for life and the re-calibration period is about 4.0sec when the key has not to been touched.
- PCB Size: 49.3 x 64.5 mm
HC-05 Bluetooth Module
- Bluetooth serial port Profile
- Bluetooth protocol: Bluetooth Specification v2.0+EDR
- Frequency: 2.4GHz ISM band
- Operating Voltage: 4V to 6V (Typically +5V)
- Operating Current: 30mA
- Modulation: GFSK(Gaussian Frequency Shift Keying)
- Emission power: ≤4dBm, Class 2
- Sensitivity: ≤-84dBm at 0.1% BER
- Speed: Asynchronous: 2.1Mbps(Max) / 160 kbps, Synchronous: 1Mbps/1Mbps
- Working temperature: -20 ~ +75Centigrade
- Serial Bluetooth module for Arduino and other microcontrollers
- Range: <100m
- Works with Serial communication (USART) and TTL compatible
- Follows IEEE 802.15.1 standardized protocol
- Uses Frequency-Hopping Spread Spectrum (FHSS)
- Can operate in Master, Slave or Master/Slave mode
- Can be easily interfaced with Laptop or Mobile phones with Bluetooth
- Supported baud rate: 9600,19200,38400,57600,115200,230400,460800.
- Dimension: 26.9mm x 13mm x 2.2 mm
Mini DC 5A Motor PWM Speed Controller 3-35V Speed Control Switch LED Dimmer
RB NEMA 23 (57mm) Coupling 6.35x8mm
Wemos D1 Mini ESP8266 NodeMCU WIFI board for Arduino
- Microcontroller: ESP-8266EX
- Operating Voltage: 3.3 V
- Digital I/O Pins: 11
- Analog Input Pins 1(Max input: 3.2V)
- Clock Speed: 80MHz/160MHz
- Flash: 4M bytes
- Length: 34.2mm
- Width: 25.6mm
- Use BRT (Bias Resistor Transistor)
- Easier into flash mode.
- 30% increase in radiating area
- Good stability.
- 11 digital input/output pins, all pins have interrupt/PWM/I2C/one-wire supported(except for D0)
- 1 analog input(3.2V max input)
- Micro USB connection
- Compatible with Arduino
- Compatible with Node MCU
- Support OTA wireless uploading
- 11 x I/O pins,1 x ADC pin
N20 Model – 40 RPM DC 12V Torque Gearbox Micro Gear Box Motor
- Reduction ratio: 1:380.
- Nominal Voltage: 6v.
- Voltage Range:Â 3v to 12v.
- RPM: 40.
- No-load Current: 40mA.
- Stall Current: 550mA.
- Stall Torque: 7500 g-cm.
- Ideal for making robots
- Lightweight, high torque, and low RPM.
- Fine craftsmanship, long-lasting, not easy to wear.
- Can easily mount a wheel on the motor’s output shaft
N20 Model – 300 RPM DC 12V Torque Gearbox Micro Gear Box Motor
- Reduction ratio: 1:50.
- Nominal Voltage: 6v
- Voltage Range: 3v to 12v
- RPM: 300
- No load Current: 40mA
- Stall Current: 550mA
- Stall Torque: 700 g-cm.
- Ideal for making robots
- Lightweight, high torque and low RPM.
- Fine craftsmanship, long-lasting , not easy to wear.
- Can easily mount a wheel on the motor’s output shaft.
Dual USB 5V 1A 2.1A Mobile Power Bank Battery Charger
- Micro USB input: 5V 1A
- Charging voltage input: 5V-6V 1A.
- Step-up voltage output: 5V 1A/2.1A (Dual output, Total 2.5A).
- USB Output: 5V 2.1A / 5V 1A(Dual USB interface)
- Charging display: intelligent digital display
- Batteries Type: liquid lithium-ion batteries (18650)
- Best for Arduino, DIY Kits, Power bank, etc.
- Protection circuit: Overcharge protection: 4.250V Overcharge protection release: 4.100V.
- Protection circuit: Over-discharge protection: 2.900V Over-discharge protection release: 3.000V.
- Idle time before LCD switch off 60secs.
- Screen size:27mm x 17mm
- Dimension: 57mm x 28mm
Digital Voltmeter Ammeter DC 0-100V 10A Dual LED Monitor Panel, Red and Blue
- Input Voltage: 4.5V to 30V DC
- Input Current: <= 20mA
- Display Colour: Red (Voltage), Blue (Current)
- Measuring Voltage Range: 0V to 100V DC
- Measuring Current Range: 0A to 10A
- Measurement Accuracy: 1%
- Minimum Voltage Resolution: 0.1V
- Minimum Current Resolution: 0.01A
- Voltage error: ±0.1%
- Current error: ±1%
- Working temperature: -10℃ to 65℃. Blue
- 28’’ device with 5 wires divided into 2 sets.
- Black, Red are for the power supply and 3 wires to measure the Voltage and Current.
- Dimension: 48mm x 29mm x 22mm