Aluminium Flexible Coupling Coupler Helical Shaft (5 x 5 mm)
- Material: Aluminium.
- Bore Diameter d1: 5 mm.
- Bore Diameter d2: 5 mm.
- Torsional stiffness: Zero backlash.
- One piece construction.
- Corrosion resistance and High Durability
- One piece construction with long-lasting performance
- Torsional stiffness: Zero backlash
- Low moment of inertia offering constant velocity
3D printer 128×64 Smart LCD controller for ramps 1.4
- RAMPS 1.4 LCD 12864 intelligent controller.
- With an SD card base on back.
- Large screen display 128×64 LCD (3.2″)
- SD card slot at the back, able to directly select a file and print
- The product comes encoder parameter adjustment can be achieved, and the file selection print
- Plug & play on the RAMPS, but need to modify the firmware to support.
- LCD 12864 Smart Controller fully supported by Marlin Firmware.
- Large screen display 128×64 LCD (3.2″)
- SD card slot at the back, able to directly select a file and print
- The product comes encoder parameter adjustment can be achieved, and the file selection print
- Plug & play on the RAMPS, but need to modify the firmware to support.
- LCD 12864 Smart Controller fully supported by Marlin Firmware.
T8 Trapezoidal Lead Screw 8MM Thread 2MM Pitch 300MM Length with Brass Nut
PR53 215mm Trapezoidal Lead Screw 8mm Thread 2mm Pitch Lead Screw with Copper Nut
PR34 2004 LCD Display Smart Controller W or Adapter for RAMPS1.4 Reprap 3D Printer
- RAMPS 1.4 2004 LCD Display intelligent controller.
- LED background light control circuit, a small function of the intelligent controller,
- With pin short time to decide on all LED turn or steering 30 seconds
- You can turn on the light time to do the long or short form of the adjustment TRIMM R4100K from 10 seconds to 2 minutes.
- Plug and play on the RAMPS, but need to modify the firmware to support.
- The product comes encoder parameter adjustment can be achieved, and the file selection print.
- With an SD card base on the back, put slicing file into the SD card and select the file on the LCD, then can be printing.
145mm Trapezoidal Lead Screw 8mm Thread 2mm Pitch Lead Screw with Copper Nut
- Rod Size: 8X145mm
- Lead (the straight distance which turn a circle): 8mm
- Nut Diameter: 8 mm.
- Color: silver and gold
- Material: Stainless steel and brass
- Mainly use for Stepping motor driving guide rail.
- T shape design, made of high-quality stainless steel material.
- Easy to install and convenient to use.
- Fine producing and practical.
Kapton Polyimide Heat Resistant/High Temperature/Thermal Tape/SublimationTape 12mm
- Color: Tawny
- Substrate material: Polyimide polymers film
- Glue Type: Silicone
- Substrate material thickness: 0.025mm
- Thickness with adhesive: 0.05mm
- Heat resistance: about 280°C
- Size:1/2" x 100ft (13mm*30m)
- Elongation: 35 %
- Temperature Range:-73°C – 260°C (-99°F - 500°F)
- High insulation, high temperature resistance, acid and alkali-resistance, low electrolysis, mechanically sound, crocking resistance, tear-resistance, without rest on surface when tear.
- Ideal for protecting sensitive printed circuit board (PCB) components,great for sublimation, HTV, heat press and heat transfer.
- Also extensive use as electrical insulation for transformer, motor, coil, capacitor and frequency conversion power supply in electronic industry.
GT2 Open Timing Belt for 3D Printer and CNC
- Pitch: 2mm
- Material: Neoprene Rubber With Fiberglass Core
- Width: 6mm
- Total Length: 1M
- Shape: Open Loop
- Core Wire Material: Glass Fiber
- Precision registration and timing with no loss of high torque carrying capability
- Minimal vibration and chordal effect
- Positive slip proof engagement
- Wide speed range, especially important when the entire speed range is developed from a single source
- Virtually no elongation (stretching) due to wear
- Power transmission efficiency is not lost with the use
- A clean operation, no need for lubrication
- Reduced noise.
- Long, dependable trouble-free service.
0.5mm 3D Printer Extruder Brass Nozzle
Thread Extruder Nozzle For 3D Printer (0.3mm)
XNUCLEO-F103RB, Improved STM32 NUCLEO Board
- Core: ARM® 32-bit Cortex™-M3
- Operating frequency: 72MHz
- Operating voltage: 2.0V-3.6V
- Package: LQFP64
- Memories : 128kB Flash, 20kB SRAM
- Interfaces : 2 x SPI, 3 x USART, 2 x I2C, 1 x CAN, 1 x USB
- AD/DA : 2 x AD (12 bit, 16 channels)
- Compatible with NUCLEO-F103RB, onboard Cortex-M3 microcontroller STM32F103RBT6
- Arduino connectivity support, easy to connect with various Arduino shields and access the massive Arduino resources
- ST Morpho headers provide full access to all STM32 I/Os, easy for peripheral expansion
- Supports mbed, build a prototype quickly by mbed SDK and online tools
- Comprehensive free software HAL library including a variety of software examples
- Comes with a separated ST-LINK/V2 module
Mini St-Link V2 Stlink Emulator Downloader Stm8 Stm32 with Metal Shell
- Support the full range of STM32 SWD interface debugging, simple interface (including power supply), 4 line speed, stable work; Interface definition shell directly address
- Support all series STM8 SWIM download debugging (common development environment such as IAR, STVD, etc.) are supported.
- Support the firmware upgrade automatically, to ensure that the ST company product support. When they leave the firmware has been upgraded to the latest V2. The J17. S4.
- Increase the 5 v power output, the output it can protect the I/O port, not afraid of error cause damage of ST-LINK V2.
- Easy interface to use pure copper plating 2.54 spacing horn, with 20 cm Dupont line, can deal with different target board line sequence, flexible connection;
- Use U disk aluminium alloy shell to protect the mainboard, convenient to carry, not afraid of static electricity, not afraid of tumbling.
- Material: metal + plastic
- Colour: Black/Red/Green/Pink/Gold/Grey/Blue/White( Randomly Sent )
- Power output: 5V
- simulator: about 5.6*2*0.8cm
- Debugging line: about 20cm
- Weight (kg): 0.012