SIM28 GPS Module Modem with GPS antenna
- Operating voltage: 12V DC.
- Frequency l1, 1575.42mhz
- C/a code 1.023mhz chip rate
- 16-channels GPS search engine
- Ultra-low-power design (38mA, typical)
- Compact size
- Built-in low noise, high gain active antenna
- Super-cohesive magnetic for installation
- High sensitivity (up to -152dBm type)
- Super-cohesive magnetic for installation
- Apply to host devices with USB or RS232
- Compatible with TTL serial
PN532 NFC/RFID Controller Shield for Arduino
- PN532 chip-set
- Operating Voltage : 3.3V ~ 5v
- Support I2C, SPI
- I2C: 3.3V ~ 24V TTL
- SPI: 3.3V TTL with 100-ohm resistors in series
- Plug and play, Arduino compatible
- Built-in PCB Antenna
- Communication distance:10cm
- Easy to change mode
- NFC/RFID PN532 shield including a tuned 13.56MHz stripline antenna
- 36-pin 0.1" header for attaching the shield to an Arduino.
- Compatible with Arduino Mega 1280 & 2560, Diecimila, Duemilanove, and UNO
GPS Modem with External Antenna
- SiRF Star IVâ„¢, GSD4e ROM version
- Tracking sensitivity -163dBm, autonomous Acquisition sensitivity -148dBm
- TTL interface output
- 48 track verification channels
- Power supply 3.3 voltage
- SMT type with stamp holes
- Small form factor with embedded SiRF star iv technology
- Removes in-band jumbers up to 80dB-Hz, track up to 8CW jammers
- Excellent sensitivity for urban canyon and foliage environments.
MEPUNO ROBOT CONTROLLER BOARD
- Microcontroller ATMEGA328 P.
- Crystal for the microcontroller: 16 MHZ
- USB type B connector
- 5volt, 12 volts regulated circuit.
- Two separate regulated 5volt power supplies.
- On-Board On/Off switch.
- OnBoard DC jack for powering up using adaptors.
- On-Board Reset Switch.
- Onboard L293D dual DC motor driver.
- Onboard TSOP IR receiver.
- On Board 3 user LEDs (with jumper selection), TX/RX indication LEDs.
- On-board connectors for analogue interfacing.
- On Board Buzzer Interface.
- Â On-Board PWM Interfacing.
- On board FTDI Driver for adruino.
- Â Berg headers for external interfacing.
- Supports I2C /3 WIRE /RF/USART serial communication standards.
CAN Bus Shield
- Implements CAN V2.0B at up to 1 Mb/s
- Industrial standard 9 pin sub-D connector
- OBD-II and CAN standard pinout selectable.
- Changeable chip select pin
- Changeable CS pin for TF card slot
- Changeable INT pin
- Screw terminal that easily to connect CAN_H and CAN_L
- Arduino Uno pin headers
- Grove connectors (I2C and UART)
- SPI Interface up to 10 MHz
- Standard (11 bit) and extended (29 bit) data and remote frames
- Two receive buffers with prioritized message storage
Msp-Exp430G2 Msp430 Launchpad
• 14-/20-pin DIP (N) Socket
• 20 pin Launchpad standard leveraging the Booster Pack ecosystem
• On-Board EZ-FET emulator featuring Energy Trace™ technology
• USB debugging and programming interface featuring a driverless installation and application UART
• serial communication with up to 9600 Baud
• Supports MSP430G2xx2, MSP430G2xx3, and MSP430F20xx devices in PDIP14 or PDIP20 packages
• Two general-purpose digital I/O pins connected to green and red LEDs for visual feedback
• Two push button for user feedback and device reset
• Easily accessible device pins for debugging purposes or as socket for adding customized extension boards
5V PCM2704 Sound Card Decoding Module DAC Decoder Board For PC Computer USB Powered
Power Line Carrier Module KQ-430F
Black PLA 1.75 mm 1 Kg Filament For 3D Printer Wanhao
- Material: PLA
- Diameter: 1.75 mm
- Printing temperature: 190-225 ° C
- Heating bed temperature: 45 ° C - 60 ° C
- Density: 1.25 g / cm³-21.5 ° C
- Melt Flow Index: 5 (10min, 2.16kg)
- Shock resistance: 5 KJ / m²
- Dimensional accuracy: 1.70 ± 0.1 mm
- Filament weight: 1 kg
- Spool size: approx. 200 mm diameter, 50 mm spool mount, 65 mm height
- Diameter tolerances of ± 0.1mm checked with laser monitor
- Smooth surface with even roundness
- Lower melting temperature
- Good flow properties
- Little odor development
- Less danger of clogging the nozzle, compared to ABS
- Compatible with almost all 1.75mm FDM printers
- No heating bed necessary
- High quality means less waste
- Easy to use
- No heating bed necessary
1.75mm HIPS 3D Printer Filament Black Wanhao
- Colour: Black
- Diameter: 1.75mm
- Material: HIPS
- Print Temperature(Degree Celsius): 230 - 270 Deg C
- Melting Temp: 230 - 270 Deg C
- Highly Detailed & Quality Outputs
- Tried and Tested by Makenica.com
- Compatible with any FDM 3D Printer.
- HIPS is stronger than PLA High Impact Polystyrene
- 1kg spools on black reel
- Highly Detailed & Quality Outputs. Every time.
- Tried and Tested by Makenica.com
- Compatible with any FDM 3D Printer.
- HIPS is stronger than PLA
- Easy to post-process.
1.75mm PLA 3D Printer Filament Black Wanhao
- Material: PLA
- Diameter: 1.75 mm
- Printing temperature: 190-225 ° C
- Heating bed temperature: 45 ° C - 60 ° C
- Density: 1.25 g / cm³-21.5 ° C
- Melt Flow Index: 5 (10min, 2.16kg)
- Shock resistance: 5 KJ / m²
- Dimensional accuracy: 1.70 ± 0.1 mm
- Filament weight: 1 kg
- Spool size: approx. 200 mm diameter, 50 mm spool mount, 65 mm height
- Diameter tolerances of ± 0.1mm checked with laser monitor
- Smooth surface with even roundness
- Lower melting temperature
- Good flow properties
- Little odor development
- Less danger of clogging the nozzle, compared to ABS
- Compatible with almost all 1.75mm FDM printers
- No heating bed necessary
- High quality means less waste
- Easy to use
- No heating bed necessary
ABS 1.75 mm 1 kg Filament for 3d printer, Dark Blue Wanhao
- Material: ABS
- Color: Dark Blue Color ABS.
- Material Diameter: 1.75mm
- Printing Temperature: 220° to 230°C
- Mounted: Spool Mounted
- Net weight: 1kg
- Diameter Accuracy: 1.75mm
- Roundness Accuracy: +/- 0.5mm +/- 0.5mm
- Density: 1.31g/cm3 1.01g/cm3
- Melt Point: 210°C 220°C
- Outer Diameter: 200 mm
- Hub Diameter: 32 mm
- Packaging Vacuum-sealed with desiccant to protect filament from humidity
- Extrusion Speed Tested up to 200mm/s
- Compatible with any FDM 3D Printer.
- ABS is stronger than PLA
- Easy to post-process.
- Environment friendly – ISO 9001 and ROHS certified