P06S-100 wired power monitor
SPP-22 Single Phase Preventer
V22-RYB Phase Sequence Relay
Heating Tube
Product Description
Heating tube elements like this one operate on the principle of Joule heating, converting electrical energy into heat as an electric current passes through a resistor inside the tube. These elements are commonly used in various applications, including space heating, cooking, water heating, and industrial processes. A103883
“PWM Generator Module for Stepper Motor Driver with Forward and Reverse Function “
- Board can be used to generate PWM signals for the stepper motor driver
- Operating Voltage: 12VDC
- Three Frequency Range
- Forward and Reverse Function.
- It has three frequency ranges selectable via onboard jumpers.
- Frequency can be measured via PUL and common cathode (GND) ports.
- The board has two sets of power input
Ublox NEO-M8N GPS Module with Compass for APM with extra connector for Pixhawk
- Ready to Connect to All APM FC with 5-pin connector Attached
- Receiver type 72-channel M8 engine
- Galileo-ready E1B/C (NEO-M8N)
- update rate1 Single GNSS: up to 18 HZ
- Position accuracy 22.0 m CEP
- Acquisition2 Cold starts: 26 s
- Sensitivity2 Tracking & Nav: –167 dBm
- On-board Compass
- Dimensions: Outer diameter 54mm
- GPS/QZSS L1 C/A, GLONASS L10F, BeiDou B1.
- SBAS L1 C/A: WAAS, EGNOS, MSAS.
- Assistance AssistNow GNSS Online.
- Assist Now GNSS Offline (up to 35 days)3.
- Assist Now Autonomous (up to 6 days).
- OMA SUPL & 3GPP compliant
- Oscillator TCXO (NEO-M8N/Q).
- Crystal (NEO-M8M).
- RTC crystal Built-In.
- Noise figure On-chip LNA (NEO-M8M). Extra LNA for.
- Lowest noise figure (NEO-M8N/Q).
- Anti-jamming Active CW detection and removal.
- Extra onboard SAW bandpass filter (NEO-M8N/Q).
- Memory ROM (NEO-M8M/Q) or Flash (NEO-M8N).
- Supported antennas Active and passive.
- Odometer Travelled distance.
- Data-logger For position, velocity, and time (NEO-M8N).
- Weight 33gm
FlexiForce Tekscan A201 Sensor
- Thickness 0.203 mm (0.008 in.)
- Length 191 mm (7.5 in.)** (optional trimmed lengths:
- 152 mm (6 in.), 102 mm (4 in.), 51 mm (2 in.))
- Width 14 mm (0.55 in.)
- Sensing Area 9.53 mm (0.375 in.) diameter
- Connector 3-pin Male Square Pin (centre pin is inactive)
- Substrate Polyester
- Pin Spacing 2.54 mm (0.1 in)
- Small size is ideal for prototyping and integration
- Thin and flexible
- Easy to use
TDA7498E Double 160W Power Amplifier Dual Channel Stereo Audio Amplifier Module Support BTL Mode
- Amplifier chip: TDA7498E
- Working voltage: DC 15-36V (Recommend 32V, 8A, if power is too small will appear distortion and so on.)
- Output power: 2 x 160W
- Number of channels: Two-channel Stereo
- Efficiency: 85%
- Applicable speaker impedance: 4/6/8ohm (8ohm is the best).
- 160-W + 160-W output power at THD = 10% with RL = 4 Ω and VCC = 36 V
- 1 x 220 W output power mono parallel BTL at THD = 10% with RL = 3 Ω and VCC = 36 V
- Wide-range single-supply operation (14 - 36 V)
- High efficiency (η = 85%)
- Parallel BTL function using the MODE pin
- Four selectable, fixed gain settings of nominally 23.8 dB, 29.8 dB, 33.3 dB and 35.8 dB
- Differential inputs minimize common-mode noise
- Standby and mute features
- Smart protection
- Thermal overload protection
- Small offset less than 20 mV
- PCB board size: 108 x 78mm
- Weight: 172g(approx.)
Arduino Mega 2560 Board
- Microcontroller: ATmega2560
- Operating Voltage: 5V
- Input Voltage (recommended): 7-12V
- Input Voltage (limits): 6-20V
- Digital I/O Pins: 54 (of which 15 provide PWM output)
- Analog Input Pins: 16
- DC Current per I/O Pin: 40 mA
- DC Current for 3.3V Pin: 50 mA
- Flash Memory: 128 KB of which 4 KB used by the boot loader
- SRAM: 8 KB
- EEPROM: 4 KB
- Clock Speed: 16 MHz
GSM GPRS + Camera Module A6C Breakout
- Operating Voltage: 3.3V – 4.2V
- Working Temperature: -30 ℃ to +80℃
- Boot Voltage: >3.4V
- Standby Current: less than 3 mA
- GSM/GPRS Frequency Band: including 850, 900, 1800, 1900 MHZ
- GPRS Class 10
- Sensibility: <-105
- Voice Call: Support
- SMS message: Support
- GPRS maximum speed: Download speed 85.6Kbps, Upload speed 42.8Kbps
- AT Command: Support standard GSM07.07, 07.05, and extended Ai Thinker command
- 2 UART: one for download, one for AT command
- Audio: Support digital and analog audio, support HR, FR, EFR, AMR audio code
- Camera resolution: 0.3M
Mh13001 220V Digital Air Humidity Control Controller Range 1% – 99%
- Model Name: MH 13001
- Voltage: 220 Volt
- Accuracy: +-3% RH
- Type: Digital
- Color: Black
- Display Type: LCD
- Input Sensor: Humidity Sensor
- Humidity: 1% ~ 99% RH\humidity measuring
- Error: ±3 percent rh
- Control range: 1 percent RH
- Power consumption:3w
- Output load: Ac 10a/220v
- Working temperature: 0°c - 80 °c
- Dimensions: 8 x 5 x 3cms
- Usage/Application: Air Humidity Controller Hygrostat Humidistat Humidification Dehumidification
MH1210W 72V 250V 10A Digital Temperature Controller
- Working voltage: DC 9-72V/AC90-250V ± 10%, 50/60 HZ
- Rated current: 10 A
- Power consumption: ≤3 W
- Measurement range: -50~110 °C
- Measurement precision: 0.1 °C
- Measurement error: ±0.3 °C
- A mini temperature controller.
- Large and clear LED display for better readability
- Wide temperature measuring range
- Heating and cooling control
- Temperature calibration
- Delay protection function
- All parameters reset to default settings after short circuit