XL4432 LORA Sensor Module
- Frequency range: 433.92M
- High sensitivity up to-121dBm
- Maximum output power: 20dBm
- Data transfer rate: 0.123-256 kbps
- FSK, GFSK, and OOK modulation mode
- 1.8-3.6V power supply
- Ultra-Thin Power Off Mode
- Digital signal strength indicator received (RSSI)
- Synchronization alarm function
- Automatic antenna connection and bidirectional switch control
- The configurable data package structure
- Before sync signal detection
- 64 bytes RX data record (FIFO)
- Low power tests
- Temperature detection and 8-bit analog to digital converter
- Operating temperature range: -20 ~ + 60 C
12V / 2A Battery Charger
- This is a durable product with a 6-month warranty.
- The adapter is easy to use.
- It comes with a long wire.
- Wide input voltage range (100VAC-280VAC).
- Very low no-load power consumption.
- Very low ripple & noise output for device safety.
- Protections against- under-over voltage/ overload/ short circuit with auto-restart on fault removal.
- Thermal shut down (140°C) with auto-restart on cold condition.
- Soft start & low inrush current.
- Isolation up to 3kv for 5sec.time period.
- High operating ambient temperature up to 60°C.
- Highly efficient, compact, durable and long life.
ESC 30A BLDC Electronic Speed Controller
- Standard 30A BLDC ESC Electronic speed controller
- Input voltage: DC 6V-16.8V(2-4S Lixx)
- BEC: 5V 2amp
- Easy handling and good compatibility
- Suitable Batteries: 2-3S LiPo.
- Application: BLDC Motors, Multirotor, RC Planes et
- Running current: 30A (Output: Continuous 30A, Burst 40A up to 10 Secs.)
- Size: 36* 26* 7mm
- Weight: 32g
SSR Relay 3-32V / 25A S-Kap
AD633 Analog Multiplier IC
- Analog Multiplier
- Four-Quadrant Multiplication
- Low Cost 8-Lead Package
- Complete—No External Components Required
- Laser-Trimmed Accuracy and Stability
- Total Error Within 2% of FS
- Differential High Impedance X and Y Inputs
- High Impedance Unity-Gain Summing Input
- Laser-Trimmed 10 V Scaling Reference
- Supply Voltage:18V
PIC18F4550 Microcontroller IC
- Maximum CPU Frequency: 48 MHz
- Architecture: 8 bit
- Program Memory (Flash): 32 kB
- RAM: 2048 byte
- Internal Oscillator: 8MHz, 32KHz
- ADC: 1 (13 channels)
- of Pins: 40
- Voltage: 2V - 5.5V
- C Compiler Optimized Architecture with optional Extended Instruction Set
- 100,000 Erase/Write Cycle Enhanced Flash Program Memory typical
- 1,000,000 Erase/Write Cycle Data EEPROM Memory typical
- Flash/Data EEPROM Retention: > 40 years
- Self-Programmable under Software Control
- Priority Levels for Interrupts
- 8 x 8 Single-Cycle Hardware Multiplier
- Extended Watchdog Timer (WDT): - Programmable period from 41 ms to 131s
- Programmable Code Protection
- Single-Supply 5V In-Circuit Serial Programming™ (ICSP™) via two pins
- In-Circuit Debug (ICD) via two pins
- Optional dedicated ICD/ICSP port (44-pin devices only)
- Wide Operating Voltage Range (2.0V to 5.5V)
ANTENNA WIFI
Antenna Specifications:
- Color: Black
- Radiation: Omni-directional
- Gain:8dBi
- Frequency Range(MHz): 2400-2500, 5150-5850MHz
- Connector Type: RP-SMA Male (Hole)
- Angle Adjustable: 90° 135° 180°
- Dimension: 16cm/ 6.3”(Unbend) / 13.5cm/ 5.31”(Bend)
- Wight: 13.5g / 0.48 oz per antenna
- Color: Black & Gold
- Length: 15cm / 5.9''
- Wight:4.4g / 0.17 oz per pigtail cable
- Connector Type: U.FL/ IPEX to RP-SMA Female
ZY-204 1660 Points Solderless Breadboard
USB Control Module 1 Channel 5V Relay Module (No Need Driver)
- Contact type: NC / COM / NO
- Input current: ≥300mA
- Input voltage: DC 5V
- Support Win7, XP 32-bit systems
- Onboard square USB interface, stable connection.
- Use an imported high-performance USB control chip.
- Application code: Green indicates that the relay is closed, the red disconnect
- Military-grade PCB board production
- Using genuine Single relay, the module uses HID technology, without any driver on the windows system plug and play, easy to use and simple
- Military-grade PCB board production
- Board power outlets and terminals, two kinds of access to power is flexible. After connecting the power, even if the computer is off or unplug the USB from the computer, the relay can also remain set.