RELAY SHEILD
- Every channel maximum convert voltage: AC 125V / DC 24V
- Every channel maximum converts current: 3A
- Interface via digital I/O pins 4,5,6, and 7
- Relay screw terminals
- Standardized shield shape and design
- LED working status indicators for each relay
- High quality relays
- COM, NO (Normally Open), and NC (Normally Closed) relay pins for each relay
- Update pin SCL, SDA, IOREF, NC.
- Arduino,Crowduino,Seeeduino,Arduino Mega compatible
- Automatic control and manual control
- 4 mechanical relays with photo-coupled circuit
- 3-M3 screw hole easy to install
- Driven by 5V / 3.3V normally open contact close
ISD1760 MODULE (75 sec)
- On-board ISD1760 chip
- Operating voltage: 5v
- 75 sec of audio playback
- Onboard microphone for direct recording
- Frequency: 6KHz or 8KHz
- Recording time: 6K/75 sec, 8K/60 sec
- Output all pin for chip control
- Easy interface with microcontrollers using 2.54mm spaced male pin headers
- High-quality natural voice reduction
- LED status indication
- Long recording time and multiple messages
- Simple operation and better voice quality
- Control not only by buttons but also by SPI from a microcontroller
- Recording, erase, play, FT, fast forward, reset volume buttons
- Dimension: 49*41.5mm
- Weight: 22gm
20/4 GREEN (LCD DISPLAY MODULE)
- Operating voltage: 5V
- Display format: 20 characters * 4 line
- Display mode: STN or FSTN
- Dot-matrix: 5*8 dots
- Character size: 2.95 * 4.75mm
- Character pitch: 3.55 * 5.35mm
- LCD driver IC: ST7066U
- 1/16 duty cycle
- Wide viewing angle and high contrast
- Works on both 8-bit parallel interface
- Operating temperature: -20 degree to 70 degree Celsius
- Low Current consumption
- Dimension: 98*60*13.6mm
- Compact size and lightweight
Elevator Limit Switch
WeMos D1 Lithium Battery Charger Board with Mini USB
- Charging Voltage: max: 10V, recommend: 5V
- Charging Current: max: 1A
- Lithium Battery voltage: 3.3-4.2V
- Boost Power Supply: 5V(max: 1A)
- Can use  D1 mini without a USB cable, it's really wireless
- Can use D1 mini anywhere, using this battery shield and a lithium Battery.
- High reliability
- Charging, when the battery run out, you do not need to unplug the battery, just use the USB port to charge.
MAX7219 led module 8 digit 7 segment display
- Power: 5V
- Colour: Red/Blue (This colour means the colour of the board, not the LED)
- Material: PCB + Electronic Components
- MAX7219 digital display control module
- This module is compatible with 5V and 3.3V microcontrollers.
- You can use it for Arduino
- Only three IO ports are used to drive the eight-digit display. MAX7219 supports flicker-free displays as well as cascading displays.
GPS Antenna Mount Folding Bracket Anodized Aluminum Carbon for M8N GPS MODULE APM PixHawk
- Material: CNC Aluminium alloy, carbon glass fiber rod
- Mounting rod diameter: 4mm
- Lead of rod: 14 cm. GPS plate diameter: 40 mm.
- Base plate diameter: 35 mm
- Mounting hole spacing: 16mm
- Easy to assemble.
- Lightweight so doesn't create unsuitability while operating
- Usage: Multicopter YS X4 X6 DJI Other
- Dimension:12cm x 10cm x 10cm
Solid Relay Module 2 channel 5v low level trigger for Arduino
- 5V Solid State 2-channel Relay
- Output With resistive fuse 240V 2A.
- Input Power: 5V DC (160MA).
- Input control signal voltage: 0 - 2.5V state low relay OFF/3.3V - 5V state high relay ON
- Working current: 12.5mA.
- Trigger voltage: 2.5v
- Trigger current: 2mA.
- Rated output load: 100V to 240V AC (50Hz/ 60Hz) 2A per channel
- Rated input power: 5V, 160mA (all channels ON)
- Triggered at Low level (or Active Low)
- Separate LEDs showing the status of each Solid-State Relay
- Input control signal:
- -Low Signal (Solid-State Relay ON / CLOSE), 0V- 2V or GND
- -High Signal (Solid-State Relay OFF / OPEN), 3.3V - 5.0V or leave it floating
- Used in PLC control, home intelligent control, industry, electronic DIY etc.
- Dimension: 25mm x 34mm x 22mm
Hi-link HLK-5M12 100-240 VAC to 5 VDC/5W Power Supply Module
- Meet UL, CE requirements,
- Rated input voltage: 100-240 VAC
- Input voltage range: 90-264 VAc
- Maximum input current: 2 A
- Input current surge: 10 A
- Maximum input voltage: 270 VAc
- Enter slow start: 50 mS
- Input Low Voltage Efficiency: Vin=110VAc,Output full-load?69 %
- Input High Voltage Efficiency: Vin=220VAc,output full-load?70 %
- Load rated output voltage: +12±0.1 VDc
- Full rated output voltage: 12±0.2 VDc
- Short-term maximum output current ?540mA
- The maximum output current for a long time: 450 mA
- Voltage Regulation ±0.2 %
- Load Regulation ±0.5 %
- Ultra-thin, ultra-small
- Low ripple and low noise
- Output overload and short circuit protection
- High efficiency, high power density
- Low power consumption, environmental protection, no-load loss <0.1W
- Output over-current protection 150-200% of the output maximum load A
- Product designed to meet the requirements of EMC and Safety Test
Solar Panel 9V 200mA
- Quality custom-design solar energy panel
- The solar cells are encased and protected by a durable outer poly frame
- Polycrystalline solar cells
- Max output power: 1.8W
- Max power voltage: 9V
- Max power current: 200mA
- Open circuit voltage: 10.8v
- Short circuit current: 220mA
- Small Epoxy Solar Panels are simple to install or add to your existing product.
- Construction requires no frame or special modifications
- Small space required for installation.
- Has 2 to 3 times the power of amorphous thin-film solar panels
- Ready to use, they require no frame or special modifications.
- For connection, just solder or crimp to the copper tape.
- Dimension: 11.5cm x 13.6cm x 3mm
- Weight 49gms
6V 300mA Solar Panel
- Max output power: 3.23W
- Max working voltage: 6.6V
- Max charging current: 490mA
- Min output power: 2.7W
- Min working voltage: 6V
- Min charging current: 450mA
- Small Epoxy Solar Panels are simple to install or add to your existing product
- Construction requires no frame or special modifications
- Small space required for installation.
- Has 2 to 3 times the power of amorphous thin-film solar panels
- Ready to use, they require no frame or special modifications.
- For connection, just solder or crimp to the copper tape.
- Laser cut to proper size and encapsulated in special sun and weather resistant materials;
- Dimensions: 13.2 Cm X 15 Cm Thickness 3mm +/- 2 mm
- Weight 136gm
