Development Boards & Modules
LDR SENSOR 20mm
Induction Cooker Sensor
STM32F103C8T6 ARM board
IR Receiver Black 5mm
- Spectral range (nm):700-1050
- Light Current IL ≥3mA
- Dark current ID< 0.1uA
- Breakdown Voltage> 30
- Maximum forward current 25mA
- Power dissipation Pd(MW): 100
- Package: Through-hole
- Diameter: 5mm
- Maximum reverse voltage 5V
- Maximum Forward Voltage 2 V-1.3V
- Operating Temperature(Celsius) -40°C- +100°C
- Fast Response
- High photosensitivity
- High reliability
20mm LDR
- Diameter: 25mm
- Â No. of Pins: 2
- Â Type of Mounting: PCB Through Hole
- Â Maximum Operating Temperature: +800C (Approx.)
- Â Dark resistance:1-20M ohm
- Good reliability
- High sensitivity
- Fast response
- Good spectrum characteristic
- Size: 20mm (50-paise size)
- .Coated with epoxy
- Miniature open frame package.
- Proxy coated.
- Moisture resistant.
- Spectral response is similar to the human eye.
U Slot Sensor MOC7811
- Model HY860D
- Output Type Photo Transistor
- Peak Emission Wavelength: 940nm
- IR Diode Forward Current: 50mA
- IR Diode Reverse Voltage: 5V
- Transistor Power Dissipation: 75mW
- Transistor Collector Current: 20mA
- Photo Transistor Collector-emitter Voltage: 30V
- Photo Transistor Emitter-collector Voltage: 5V
- Diode Power Dissipation: 100mW
- Operating Temperature Range: -55~100 Celsius Degree
- Number of Pins 4
- Hole Diameter: 3mm
- Material: Plastic, Metal
- Non-Contact Switching
- For Direct PC-Board or Dual-In-Line Socket Mounting
- Fast Switching Speed
- Colour: Black
- Dimension: 22 x 22 x 6mm
- Weight: 8gm
LM35 SENSOR
- Calibrated Directly in Celsius (Centigrade)
- Operates from 4 V to 30 V
- Linear + 10-mV/°C Scale Factor
- ±0.5°C Ensured Accuracy (at 25°C)
- Can measure temperature ranging from -55°C to 150°C
- Less than 60-µA Current Drain
- Low Self-Heating, 0.08°C in Still Air
- Non-Linearity Only ±¼°C Typical
- Low-Impedance Output, 0.1 Ω for 1-mA Load.
- Drain current is less than 60uA
- The output voltage is directly proportional (Linear) to temperature (i.e.) there will be a rise of 10mV (0.01V) for every 1°C rise in temperature
- Suitable for Remote Applications
- Low-cost temperature sensor
- Available in TO-92, TO-220, TO-CAN, and SOIC package
IR Receiver 3 Leg Black Small
- Sensing distance: 45m
- P.F frequency: 38.0 kHz
- Supply voltage: 2.5V- 5.5V
- Mounting type: through hole
- Operating temperature: -25°C ~ 85°C (TA)
- Directivity: 45°
- Supply Current: 350µA
- High-Level Pulse Width: 0.8 ms
- Low-Level Pulse Width: 0.8 ms
- Power Dissipation: 10 mW
- Proper Shielding Against EMI
- High Immunity against Ambient Light
- Photo Detector and Preamplifier in single Package
- Low Supply Current
- Insensitive to Noise and Supply Voltage Ripple
USB PC Intelligent Control Module 2 Channel 5V Relay Module (No Need Driver)
- Contact type: NC / COM / NO
- Input current: ≥300mA
- Input voltage: DC 5V
- Support Win7, XP 32-bit systems
- Onboard square USB interface, stable connection.
- Use an imported high-performance USB control chip.
- Application code: Green indicates that the relay is closed, the red disconnect
- Military-grade PCB board production
1/4 CMOS 640*480 USB Camera with Collapsible cable for Raspberry Pi
• Interface: USB 2.0
• Sensor: 1/4 Cmos
• Operating Current: <120 mA
• Picture Format: VGA
• Resolution: 640X480
• Supports 300k pixels, a maximum resolution of 640×480, and VGA/ YUY2 packed formats
• Dimension: 40mm × 15mm × 30mm; designed for Raspberry Pi and PC
• With a retractable USB cable, convenient to store
• Applies USB 2.0 High-speed Sensor, plug-and-play, no driver installation
• High definition and true colour images.
• max pixels: 12m pixels
NODEMCU ESP8266-12 USB CH340
- 11 b/g/n Wi-Fi Direct (P2P), soft-AP
- Power input: 4.5V to 9V (10VMAX), USB-powered
- Transfer rate: 110-460800bps
- Support UART / GPIO data communication interface
- Support Smart Link Smart Networking
- Working temperature: -40°C ~ + 125°C
- Drive Type: Dual high-power H-bridge
- Don’t need to download resetting
- A great set of tools to develop ESP8266
- Flash size: 4MByte
- Integrated TCP/IP protocol stack
- Use CH340G to replace the CP2102.
- Integrated low power 32-bit CPU
- Advanced API for hardware IO, which can dramatically reduce the redundant work for configuring and manipulating hardware.
- Integrated TR switch, balun, LNA, power amplifier, and matching network
- Integrated PLL, regulators, DCXO, and power management units
- On-board USB to serial chip to easily program and upload codes from the Arduino IDE
- Embeds logic level converter circuits
- Has onboard 3.3V regulator to ensure enough power to function as your go-to WiFi chip!
- Easy access to the GPIO pins for easy prototyping