Waveshare 5inch HDMI LCD (B) 800×480
- 800x480 high hardware resolution
- Resistive touch control
- Supports popular mini PCs such as Raspberry Pi, BB Black, as well as general desktop computers
- When works with Raspberry Pi, supports Raspbian/Ubuntu/Kali/Retropie/WIN10 IOT, driver free
- When working as a computer monitor, supports Windows 10/8.1/8/7, single touch, and driver free
- The backlight can be turned off to lower power consumption
- 5mm audio jack speaker provided and supports HDMI audio output
- Supports popular game consoles like Microsoft XBOX360 Sony PS4 and Nintendo Switch etc.
- Multi languages OSD menu for power management brightness/contrast adjustment etc.
- Also supports VGA input(specific cable is required and should be purchased separately)
- Dimensions:18 x 10 x 9 cm
- Weight: 200 Grams
Waveshare 10.1inch HDMI LCD (B) (with case) 1280×800 IPS
- IPS screen,1280×800 high resolution
- Capacitive touch control supports up to ten-points touch
- When works with Raspberry Pi, supports Raspbian, Ubuntu, single touch, and driver free
- When working as a computer monitor, supports Windows 10/8.1/8/7, ten-points touch, and driver free
- Supports Banana Pi, Banana Pro, comes with Lubuntu, Raspbian images
- Supports BB Black, comes with Angstrom image
- HDMI interface for displaying, USB interface for touch control
- Supports 5-level backlight adjustment.
- Case Material: high-quality black Acrylic
- Comes with a back holder, 45degree tilt angle
- Dimensions: 18 x 10 x 9 cm
- Weight: 800gm
WS2812 LED BREAKOUT BOARD
- Input Voltage: -0.5～VDD+0.5V
- Supply voltage: 5v
- Operating voltage: 4v -7v
- Integrating control circuit and RGB chip
- Built-in signal reshaping circuit
- Built-in electric reset circuit and power lost reset circuit
- 256 brightness and 16777216 colour display
- Viewing angle: 120 degree
- Cascading port transmission signal
- Red Vf: 1.8~2.2V
- Green Vf: 3.0~3.2v
- Blue Vf: 3.2~3.4V
- Red Wavelength: 620~630 nm
- Green Wavelength: 515~530 nm
- Blue Wavelength: 465~475 nm
- Red luminous intensity(20mA): 550~700mcd
- Green luminous intensity(20mA): 1100~1400mcd
- Blue luminous intensity(20mA): 200~400mcd
- Dimension: 1.8*1.3*0.8mm
USBASP PROGRAMMER
- No special USB controller required
- Programming speed is up to 5Kbytes/sec
- Working platform: Linux, Windows, Mac OS X
- Allows to read or write the microcontroller EEPROM, firmware, fuse bits, and lock bits
- No special controllers or SMD components are needed.
- Target is supported by the SCK option with a low clock speed (<1.5MHz)
- Programming status and Bus status are easily identified
- The easy interface is achieved by Header pins for various ISP header pins
- Dimension: 63.3*20.5*10.5mm
- Weight: 15gm
PL2303 USB TO TTL CONVERTER
- USB specification 2.0 compliant with full-speed 12Mbps.
- Operation Level-Digital 5V
- Power Supply-External 5V
- Standard USB type A male and TTL 6pin connector.
- 6 pins for 3.3V, RST, TXD, RXD, GND & 5V.
- All handshaking and modem interface signals.
- Baud rates: 300 bps to 1.5 Mbps.
- Byte receives buffer; 640 bytes transmit buffer.
- Hardware or X-On/X-Off handshaking supported.
- Event character support Line break transmission.
- USB suspend states supported via SUSPEND pins.
- Supports Windows 98SE, 2000, XP, Vista, Window7, Mac OS 9, Mac OS X & Linux 2.40.
- Simple serial communication.
- Router or ADSL firmware upgrade.
- Easy to use, RX to the MCU's TX; TX to the MCU's RX. and then connected to the GND. Without having to use the MAX232 conversion.
SI4432 WIRELESS MODULE
- Power supply: 1.8-3.6 V
- Maximum output power: 20dBm
- Data transfer rate:0.123-256kbps
- Frequency range: 433.92MHz
- Sensitivity up to 20dBm
- FSK, GFSK, and OOK modulation
- Ultra-low-consumption shutdown mode
- Digital received signal strength indication (RSSI)
- Waketime
- Automatic matching and two-way antenna switch control
- Configurable packet structure
- Preamble detection
- 64-byte send and receive data register (FIFO)
- Low power detection
- 8-bit ADC and temperature sensor
- Integrated voltage regulator
- Frequency hopping
- Operating Temperature:-20 degree +60 degrees Celsius
- Transmission Distance (Maximum):1000 meters
- Power-on reset function
- Built-in lens adjustment
- Dimension :19*19*1 mm
- Weight :0.9 g
8 CHANNEL TTP226 CAPACITIVE TOUCH SENSOR
- On-board TTP226 capacitive touch induction IC
- On-board 8-way level indicator
- Working voltage: 2 V to 5.5 V DC
- Adjustable output mode, key output mode
- Low power consumption
- Can replace the traditional touch of a button
- Fixture screw-holes for easy positioning & installation
- Typical high Voh = 0.8VCC
- Typical Vol = 0.3VCC
- Output Sink Current: 8mA
- Output pin pull-up current: 4mA
- Response time (Low Power mode): 220mS
- Response time: 60mS
- Onboard 8-level status indicator
- Dimension: 47*46mm
TEC1-12705 MODULE
- Model number: TEC1-12705
- Operating Voltage: 12V
- Maximum Voltage- Vmax (V) : 15V
- Maximum Current- Imax (A) : 5.2A
- Maximum Power: 54 W
- Power Cord: 350mm
- Internal resistance: 1.98 Ohm +/- 10%
- Life expectancy: 200,000 hours
- Failure rate based on long-time testing: 0.2%.
- Easy transition between the hot side to the cool side and vice-versa just by reversing the polarity of the supply.
- Quality tested cooling cells.
- Solid-state, vibration-free, noise-free.
- Simple to install and operate.
- Should use with a heat sink
- Temperature: 138°C
- Wire Insulation Material: Teflon
- Dimension: 40x40x4.0mm
- Weight: 29g
SPEED MEASUREMENT SENSOR
- Using imported groove optical coupling sensor, width 5mm.
- Good signal and waveform
- The strong driving ability for more than 15mA.
- Use the LM393 wide voltage comparer.
- It has the output state light, if the output is high level, the lights are off. If the output is low level, it is on.
- If it is covered, it will output a high level; otherwise, its output low level.
- Equipped with a fixed bolt hole, easy install.
- The DO output interface can be directly connected to a micro-controller IO port if there is a block detection sensor, such as the speed of the motor encoder can detect.
- DO modules can be connected to the relay, limit switch, and other functions, it can also with the active buzzer module, compose alarm.
RDA9851 CPR9851S Bluetooth MP3 FM Module
- Supply voltage 3.2V ~ 4.2V
- Current consumption when the normal operating current 45mA, 32mA Play Pause
- Separation 50dB SNR 70dB
- supports MP3/WMA/WAV/SBC
- Wireless stereo transmission, Bluetooth phone
- BT card reader as it supports USB host so can read data from SD or MMC
- Stereo audio Line-in input
- IR remote control
- Bluetooth version Bluetooth V2.1 + EDR
- UART port for serial communication, and can customize AT communication protocol
- Integrated power management circuit
- High-speed UART interfaces, for debugging or updating software
- Support 3X3 matrix key
- Two controllable LED, support external amplifier mute function
- the internal integration 2x1W amplifier supports dual-channel amplifier output directly ( 2x6 recommended European speakers, power is about 2x0.75W)
- Modulation PSK 3Mbps, 4-DQPSK and 8DPSK
- Supports HFP / HSP, OPP, A2DP/AVRCP, PBAP profiles
- Sensitivity (0.1% BER)-82dBm
- Class2 and class3 transmit power to meet the requirements of the transmit power can provide +7 dBm maximum transmit power
- Operating temperature -20 ~ +50 degree
- Dimension: 26mm x 19mm x 2.05mm
PN532 NFC MODULE
- Operating Voltage : 3.3V ~ 5v
- Support I2C, SPI, and HSU (High-Speed UART)
- I2C / UART: 3.3V ~ 24V TTL
- SPI: 3.3V TTL with 100-ohm resistors in series
- Plug and play, Arduino compatible
- Built-in PCB Antenna
- Communication distance: 5cm-7cm
- Easy to change mode: with a small SMD Toggle Switch
- Longer distance: the reading distance becomes 5~7cm,
- On-board level shifter, Standard 5V TTL for I2C and UART 3.3V TTL SPI
- Work as an RFID reader/writer
- Work as a 1443-A card or a virtual card
- Support NFC with Android phone
- Small size
- Dimensions: 42.7*40.4*4mm
PCF8591 ADC-DAC
- Operating voltage range: 2.5V-6V
- Low standby current
- I2C bus serial input/output
- PCF8591 by 3 hardware address pins addressing
- PCF8591 I2C bus speed sampling rate decided 4 analogue inputs programmable single-ended or differential input
- Automatic incremental channel selection
- PCF8591 analogue voltage range from VSS to VDD
- On-chip track-and-hold circuit
- 8-bit successive approximation A / D converter
- 1 analogue output DAC gain
- Single power supply
- Module power supply indicator lights
- DA output indicator
- Dimension: 3.6*2.3cm